Related Manuals for Siemens SIMATIC NET RUGGEDCOM RMC
Summary of Contents for Siemens SIMATIC NET RUGGEDCOM RMC
- Page 1 Installation Manual SIMATIC NET Rugged Ethernet Switches RUGGEDCOM RMC Edition 04/2021 https://www.siemens.com...
- Page 2 Preface Introduction Installing the Device SIMATIC NET Communication Ports Rugged Ethernet Switches RUGGEDCOM RMC Technical Specifications Certification Installation Manual 04/2021 C79000-G8976-1006-10...
- Page 3 Note the following: WARNING Siemens products may only be used for the applications described in the catalog and in the relevant technical documentation. If products and components from other manufacturers are used, these must be recommended or approved by Siemens. Proper transport, storage, installation, assembly, commissioning, operation and maintenance are required to ensure that the products operate safely and without any problems.
-
Page 4: Table Of Contents
Accessing Documentation ....................... v Registered Trademarks ......................v Warranty ..........................v Training ..........................vi Customer Support ........................vi Contacting Siemens ........................ vi Introduction ........................... 1 Feature Highlights ....................1 Description ......................2 Required Tools and Materials ................. 3 Decommissioning and Disposal ................3 Supported Fiber Optic Cables ................ - Page 5 Table of Contents Dimension Drawings ................... 21 Certification ......................... 23 Approvals ......................23 5.1.1 CSA ........................23 5.1.2 European Union (EU) ..................23 5.1.3 FCC ........................24 5.1.4 FDA/CDRH ......................24 5.1.5 ISED ........................24 5.1.6 ISO ........................24 5.1.7 RoHS ........................
-
Page 6: Preface
Warranty Siemens warrants this product for a period of five (5) years from the date of purchase, conditional upon the return to factory for maintenance during the warranty term. This product contains no user-serviceable parts. Attempted service by unauthorized personnel shall render all warranties null and void. -
Page 7: Training
Siemens Sales representative. Customer Support Customer support is available 24 hours, 7 days a week for all Siemens customers. For technical support or general information, contact Siemens Customer Support through any of the following methods: Online Visit http://www.siemens.com/automation/support-request... - Page 8 Preface Contacting Siemens 300 Applewood Crescent Concord, Ontario Canada, L4K 5C7 Telephone Toll-free: 1 888 264 0006 Tel: +1 905 856 5288 Fax: +1 905 856 1995 E-Mail ruggedcom.info.i-ia@siemens.com https://www.siemens.com RUGGEDCOM RMC Installation Manual, 04/2021, C79000-G8976-1006-10...
- Page 9 Preface Contacting Siemens viii RUGGEDCOM RMC Installation Manual, 04/2021, C79000-G8976-1006-10...
-
Page 10: Introduction
Introduction The RUGGEDCOM RMC is an industrially hardened fiber optical media converter specifically designed to operate in harsh environments such as those found in electric utility substations and factory floors. The RUGGEDCOM RMC provides industrial strength Ethernet copper-to-fiber media conversion allowing for 10Base-T to 10Base- FL and 100Base-TX to 100Base-FX over SingleMode or MultiMode fiber optics. -
Page 11: Description
Introduction 1.2 Description • Transmit and receive data LED indicators for quick and easy troubleshooting • Fully integrated power supply connects directly to power source permanently for reliable maintenance-free operation Universal Power Supply Options • 24VDC, 48VDC or HI (88-300VDC / 85 - 264VAC) options for worldwide operability •... -
Page 12: Required Tools And Materials
Introduction 1.3 Required Tools and Materials State Description Green Power is on Power is off LINK/ACT LEDs Indicate the connection status of the fiber optic Ethernet ports. State Description LINK Green (Solid) Link is established Green Port activity (Blinking) Power Supply Terminal A pluggable terminal. -
Page 13: Supported Fiber Optic Cables
Introduction 1.5 Supported Fiber Optic Cables Recycling and Disposal For environmentally friendly recycling and disposal of this device and related accessories, contact a facility certified to dispose of waste electrical and electronic equipment. Recycling and disposal must be done in accordance with local regulations. -
Page 14: Installing The Device
This product contains no user-serviceable parts. Attempted service by unauthorized personnel shall render all warranties null and void. Changes or modifications not expressly approved by Siemens AG could invalidate specifications, test results, and agency approvals, and void the user's authority to operate the equipment. -
Page 15: General Procedure
Visually inspect each item in the package for any physical damage. Verify all items are included. Note If any item is missing or damaged, contact Siemens for assistance. Mounting the Device The RUGGEDCOM RMC is designed for maximum mounting and display flexibility. It can be equipped with adapters that allow it to be attached to a DIN rail or panel. -
Page 16: Mounting The Device On A Din Rail
Installing the Device 2.3.1 Mounting the Device on a DIN Rail Forced airflow is not required. However, any increase in airflow will result in a reduction of ambient temperature and improve the long-term reliability of all equipment mounted in the rack space. Note For detailed dimensions of the device with either DIN rail or panel hardware installed, refer to... - Page 17 Installing the Device 2.3.1 Mounting the Device on a DIN Rail Removing the Device To remove the device from a DIN rail, do the following: Insert a flathead screwdriver into the slot of the sliding release and move it down. DIN Rail DIN Rail Adapter Figure 2.2 Removing the Device from a DIN Rail...
-
Page 18: 2.3.2 Mounting The Device To A Panel
Installing the Device 2.3.2 Mounting the Device to a Panel 2.3.2 Mounting the Device to a Panel To mount the device to a panel, do the following: Disassemble the device and panel adapter. Remove the screw at the bottom of the adapter. Pull the device out of the adapter. - Page 19 Installing the Device 2.4 Setting the Operating Mode operate at various duplex modes and speeds. Choose the appropriate operating mode according to the fiber link partner. MODE Switch Figure 2.4 MODE Switch Configuration MODE Switch Position Description Transparent Mode 10/100 Auto- negotiating transparent mode HDX Mode Half-Duplex...
-
Page 20: Connecting Power
Note Siemens requires the use of external surge protection in VDSL applications where the line may be subject to surges greater than that for which the device is rated. Use the following specifications as a guide for VDSL external surge protection: •... - Page 21 Installing the Device 2.5.1 Connecting AC Power Connect the positive wire from the power source to the positive/live (+/L) terminal on the terminal block. Positive/Live (+/L) Terminal Negative/Neutral (-/N) Terminal Surge Ground Terminal Braided Ground Cable Figure 2.5 Terminal Block Wiring Connect the negative wire from the power source to the negative/neutral (-/N) terminal on the terminal block.
-
Page 22: 2.5.2 Connecting Dc Power
Installing the Device 2.5.2 Connecting DC Power 2.5.2 Connecting DC Power To connect a high or low DC power supply to the device, do the following: NOTICE Electrical hazard – risk of damage to equipment Before testing the dielectric strength (HIPOT) in the field, remove the braided ground cable connected to the surge ground terminal and chassis ground. - Page 23 Installing the Device 2.5.2 Connecting DC Power RUGGEDCOM RMC Installation Manual, 04/2021, C79000-G8976-1006-10...
-
Page 24: Communication Ports
Communication Ports The RUGGEDCOM RMC can be equipped with various types of communication ports to enhance its abilities and performance. Port 1 Port 2 Figure 3.1 Port Assignment Port Type Copper Ethernet Port Copper Ethernet Port Copper Ethernet Port The RUGGEDCOM RMC supports a single 10/100Base-TX Ethernet port that allows connection to a standard Category 5 (CAT-5) unshielded twisted-pair (UTP) cable with an RJ45 male connector. -
Page 25: Fiber Optic Ethernet Ports
Communication Ports 3.2 Fiber Optic Ethernet Ports excessive noise and interference, but more importantly, create a potential shock hazard that can result in serious injury. NOTICE For substation applications, do not use the copper Ethernet port to interface with field devices across distances that could produce high levels of ground potential rise (i.e. - Page 26 Communication Ports 3.2 Fiber Optic Ethernet Ports Available Ports Tx Connector Tx Connector Rx Connector Rx Connector Figure 3.4 LC Port Figure 3.3 MTRJ Port Tx Connector Rx Connector Figure 3.5 ST Port Specifications For specifications on the available fiber optic Ethernet ports, refer to "Fiber Optic Ethernet Port Specifications (Page 19)".
- Page 27 Communication Ports 3.2 Fiber Optic Ethernet Ports RUGGEDCOM RMC Installation Manual, 04/2021, C79000-G8976-1006-10...
-
Page 28: Technical Specifications
Technical Specifications This section provides important technical specifications related to the device and available modules. Power Supply Specifications Power Minimum Input Maximum Input Internal Max. Power Supply Type Fuse Rating Consumption 24 VDC 18 VDC 36 VDC 3.15A (T) 48 VDC 36 VDC 59 VDC 88 VDC... -
Page 29: Supported Networking Standards
3 dBm. To convert from peak to average, subtract 3 dBm. • Maximum segment length is greatly dependent on factors such as fiber quality, and the number of patches and splices. Consult a Siemens Sales associate when determining maximum segment distances. Data... -
Page 30: Mechanical Specifications
Technical Specifications 4.6 Mechanical Specifications Parameter Range Comments Ambient Storage Temperature -40 to 85 °C (-40 to 185 °F) Typical. May change based on which fiber optic transceivers are installed. For more information, refer to "Fiber Optic Ethernet Port Specifications (Page 19)". - Page 31 Technical Specifications 4.7 Dimension Drawings 67.3 62.2 92.5 58.4 82.2 35.6 11.4 Figure 4.2 Panel Mount Dimensions RUGGEDCOM RMC Installation Manual, 04/2021, C79000-G8976-1006-10...
-
Page 32: Certification
UL 62368-1 Information Technology Equipment – Safety – Part 1: General Requirements) 5.1.2 European Union (EU) This device is declared by Siemens AG to comply with essential requirements and other relevant provisions of the following EU directives: • EN 62368-1 Information Technology Equipment –... -
Page 33: 5.1.3 Fcc
Certification 5.1.3 FCC The device is marked with a CE marking and can be used throughout the European community. A copy of the CE Declaration of Conformity is available from Siemens AG. For contact information, refer to "Contacting Siemens (Page vi)". -
Page 34: Rohs
Certification 5.1.7 RoHS 5.1.7 RoHS This device is declared by Siemens AG to meet the requirements of the following RoHS (Restriction of Hazardous Substances) directives for the restricted use of certain hazardous substances in electrical and electronic equipment: • China RoHS 2... - Page 35 Ports AC Power 5 kV Ports Siemens specified severity level. IEEE 1613 EMC Immunity Type Tests Note The RUGGEDCOM RMC meets Class 2 requirements for an all-fiber configuration and Class 1 requirements for copper ports. Description Test Levels Enclosure Contact ±...
- Page 36 Certification 5.2 EMC and Environmental Type Tests Description Test Levels Fast Transient Signal Ports ± 4 kV @ 2.5 kHz DC Power Ports ± 4 kV AC Power Ports ± 4 kV Earth Ground Ports ± 4 kV Oscillatory Signal Ports 2.5 kV common mode @ 1MHz DC Power Ports 2.5 kV common, 1 kV...
- Page 37 Certification 5.2 EMC and Environmental Type Tests RUGGEDCOM RMC Installation Manual, 04/2021, C79000-G8976-1006-10...
- Page 38 Further Information Siemens RUGGEDCOM https://www.siemens.com/ruggedcom Industry Online Support (service and support) https://support.industry.siemens.com Industry Mall https://mall.industry.siemens.com Siemens AG Digital Industry Process Automation Postfach 48 48 90026 NÜRNBERG GERMANY...