Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Woodley Clinispin HORIZON 12 Flex
Summary of Contents for Woodley Clinispin HORIZON 12 Flex
- Page 1 Clinispin HORIZON 12 Flex, 24 Flex Operator’s Manual...
-
Page 3: Table Of Contents
ABLE OF ONTENTS Model Description............................... 1 Features ..................................1 Intended Use ................................1 Warranty ..................................1 Initial Setup ................................. 2 Quick Start................................3 Quick Programme a Cycle without Saving ......................... 4 Cycle Lock ................................5 Single Cycle Lock ................................ 5 Preset Lock ................................. -
Page 4: Model Description
[Refer to the clinical laboratory method specified by the specimen receptacle manufacturer or established by the medical technology for the products applications.] ARRANTY Woodley Equipment Company warranties that this centrifuge is free from defects in workmanship and parts for 2 years. Woodley Equipment Company – + 44 (0) 1204 669033 – sales@woodleyequipment.com| Page 1... -
Page 5: Initial Setup
Plug the line cord into an approved electrical outlet. E SURE THE ELECTRICAL OUTLET IS ALWAYS ACCESSIBLE AS THE LINE CORD IS THE MEANS OF EMERGENCY ISCONNECTION Woodley Equipment Company – + 44 (0) 1204 669033 – sales@woodleyequipment.com| Page 2... -
Page 6: Quick Start
Pressing the UNLOCK button during operation will terminate the Stop run and unlock the lid after the rotor has come to a stop. Cycle Selection Press the CYCLE button to select the desired saved cycle. Woodley Equipment Company – + 44 (0) 1204 669033 – sales@woodleyequipment.com| Page 3... -
Page 7: Quick Programme A Cycle Without Saving
“Beeper” shows on the upper screen. Switch ON or OFF with the On or Off keys next to the lower screen. This setting will apply to all cycles. Press the GEAR button again to save. Woodley Equipment Company – + 44 (0) 1204 669033 – sales@woodleyequipment.com| Page 4... -
Page 8: Cycle Lock
With lid open and while not in Settings mode, press and hold the Cancel Preset Lock UNLOCK button for 5 seconds until two beeps are heard. Saved cycles can again be edited or programmed. Woodley Equipment Company – + 44 (0) 1204 669033 – sales@woodleyequipment.com| Page 5... -
Page 9: Setting Or Modifying A Saved Cycle
ELETING A YCLE To delete a selected cycle, press the GEAR button and simply set either TIME or SPEED to zero and save by pressing the CYCLE button. Woodley Equipment Company – + 44 (0) 1204 669033 – sales@woodleyequipment.com| Page 6... -
Page 10: Reset To Factory Settings
60 seconds have elapsed, press the UNLOCK button. The lid will unlock for another 15 seconds. o Turn the lid knob counterclockwise and open the lid. The lid light will turn off. o You may now safely remove the samples. Woodley Equipment Company – + 44 (0) 1204 669033 – sales@woodleyequipment.com| Page 7... -
Page 11: Balancing Loads
When loading only 3 tubes, they must be of equal weight. Buckets can be placed around the rotor in any of the rotor loading configurations shown. Each bucket must be loaded symmetrically with tubes as above. Woodley Equipment Company – + 44 (0) 1204 669033 – sales@woodleyequipment.com| Page 8... -
Page 12: Care And Preventative Maintenance
Woodley Equipment Company – + 44 (0) 1204 669033 – sales@woodleyequipment.com| Page 9... -
Page 13: Troubleshooting
Check the setting by following the instructions in the section on the desired value Setting or Modifying a Saved Cycle. If the preset is not the desired Woodley Equipment Company – + 44 (0) 1204 669033 – sales@woodleyequipment.com| Page 10... - Page 14 Make sure that the screw in the centre of the rotor is tight. Clicking noise during braking gets loud o Tighten the centre screw on the lid hinge. Lid does not stay up Woodley Equipment Company – + 44 (0) 1204 669033 – sales@woodleyequipment.com| Page 11...
-
Page 15: General Specifications
RCF or G-force = 0.0000284 x Rotor Radius (cm) x (RPM) Rotor Radius (in) x (RPM) HORIZON 12 Flex HORIZON 24 Flex Radius 13.3 cm (5.25 in) 15.3 cm (6 in) Woodley Equipment Company – + 44 (0) 1204 669033 – sales@woodleyequipment.com| Page 12... - Page 16 Product Family: Clinispin HORIZON Series (HORIZON 12 Flex, 24 Flex) Complies with UL61010-1/CSA C22.2 No. 61010-1 and IEC61010-2-020 Protected by U.S. Patents #6,811,531, # 7,422,554, #D718,463, & #D734,489. Other Patents Pending RoHS FDA LISTED Compliant INSTRUCTIONS FOR DISPOSAL OF WEEE BY USERS IN THE EUROPEAN UNION This product must not be disposed of with other waste.
Need help?
Do you have a question about the Clinispin HORIZON 12 Flex and is the answer not in the manual?
Questions and answers