Kenwood TK-3217 Service Manual page 11

TK-3217
■ Flow Chart (Source transceiver)
[<B]+Power ON
Is Data
password
set?
No
Clone mode
Start the clone function
5. Self Programming Mode
Write mode for frequency data and signaling, etc. To be
used ONLY by the authorized service person maintaining the
user's equipment. After programming, reset the FPU to the
"Self- Programming" disabled mode. Transceivers CANNOT be
delivered to the end-user in the self-programming mode.
5-1. Enter to the Self Programming Mode
Press and hold the [S] key for 2 seconds while turning the
transceiver power on.
When the transceiver enters in the self programming mode,
"1- 1" is displayed 2 seconds after "SELF " is displayed.
Note :
This mode (self programming mode) cannot be set when it
has been disabled with the FPU.
5-2. Adding the Data Password
If the Data password is set to the transceiver, you must
enter the password to activate a self programming mode. The
maximum length of the password is 6 digits.
The following describes how to enter the password.
1. Press and hold the [S] key for 2 seconds while turning the
transceiver power on.
2. "SLF.LOCK.R"(When the Read authorization password is
set to the transceiver.) / "SLF.LOCK.W" (When the
Overwrite password is set to the transceiver.) is displayed
on the LCD.
3. If the [selector] knob is rotated while "SLF.LOCK.R"/
"SLF.LOCK.W" is displayed, the number (0 to 9) flashes on
the LCD.
When you press the [C>] key, the currently selected
number is determined.
10
REALIGNMENT /
Yes
"CLN.LOCK.R"/"CLN.LOCK.W"
is displayed.
Enter the password and
then press the [S] key.
No
Is password
correct?
Yes
[S]
模式组合
■ 流程图(主对讲机)
[<B]＋电源ON
是否设置 是
了数据密码?
否 "CLN.LOCK.R"/"CLN.LOCK.W"
复制模式
[S]
开始复制功能
5. 自台编程模式
频率数据和信令等的写入模式。 只可以由负责维护用户设备
的授权服务人员使用。编程之后，复位自台编程模式为禁用状
态。对讲机不能以自台编程模式开启的状态交付给最终用户。
5-1. 进入自台编程模式
打开对讲机电源的同时，持续按[S]键 2 秒。
当对讲机进入了自台编程模式，显示"SELF"2 秒钟，然后
显示"1-1" 。
注∶
当自台编程模式被 FPU 禁用时，此模式不能被设定。
5-2. 增加数据密码
如果数据密码被设定到对讲机， 则您必须输入密码来激活自
台编程模式。密码的最大长度为 6 位数字。
输入密码的方法说明如下。
1. 打开对讲机电源的同时，持续按[S]键 2 秒。
2."S L F . L O C K . R " ( 当读取授权密码被设定到对讲机时) ／
"SLF.LOCK.W" (重写密码被设定到对讲机时)被显示在 LCD。
3. 在"SLF.LOCK.R"／"SLF.LOCK.W"被显示时，如果[选择
器]旋钮被转动，在 LCD 上会闪烁出数字(0~9)。
当您按了[C>]键，通常被选择的数字将被确定。
被显示。
输入密码然后按[S]键。
否
密码是否正确?
是