Table of Contents
Advertisement
en Troubleshooting
Fault
The operation does not start or is
interrupted.
Appliance does not heat up and
"Demo mode is switched on" ap-
pears in the display.
The appliance does not start and
"Cooking compartment too hot"
appears in the display.
The time is not displayed when
the appliance is switched off.
The interior lighting does not
work.
Maximum operating time
reached.
A message with "D" or "E" ap-
pears in the display, e.g. D0111
or E0111.
The cooking result is not satis-
factory.
19.2 Replacing the oven light bulb
If the light in the cooking compartment fails, change
the oven light bulb.
Note: Heat-resistant, 25-watt, 230 V halogen bulbs are
available from the after-sales service or specialist retail-
ers. Only use these bulbs. Hold the new halogen bulbs
only with a clean, dry towel. This increases the service
life of the bulb.
WARNING ‒ Risk of burns!
The appliance and its parts that can be touched be-
come hot during use.
Caution should be exercised here in order to avoid
▶
touching heating elements.
Young children under 8 years of age must be kept
▶
away from the appliance.
22
Cause and troubleshooting
Different causes are possible.
Check any notifications that appear in the display.
▶
→ "Displaying information", Page 11
Device is in demo mode.
Briefly disconnect the appliance from the power supply by switching the cir-
1.
cuit breaker in the fuse box off and back on again.
Switch off demo mode within three minutes in the
2.
→ "Basic settings", Page 15.
There has been a power cut.
Open and close the appliance door once after a power failure.
▶
a The appliance is checked and is ready to use.
The cooking compartment is too hot for the selected dish or type of heating.
Allow the cooking compartment to cool down and start again.
▶
Basic setting has been changed.
Change the basic setting for the time display.
▶
→ "Basic settings", Page 15
The halogen lamp is defective.
Change the oven light bulb.
▶
→ "Replacing the oven light bulb", Page 22
To prevent an unwanted permanent operation, the appliance automatically stops
heating after several hours if the settings are unchanged. A message appears in
the display.
The point at which the maximum operating time is reached is determined by the
corresponding settings for an operating mode.
To continue operation, switch off the appliance with
1.
Then use
to switch on the appliance and set the required operation.
2.
Tip: To prevent the appliance from switching off when you do not want it to, set
a cooking time.
The electronics have detected a fault.
Switch the appliance off and on again.
1.
a If the fault was a one-off, the message disappears.
If the message appears again, call the after-sales service. Please specify the
2.
exact error message when calling.
→ "Customer Service", Page 23
Settings were unsuitable.
Setting values, e.g. temperature or cooking time, depend on the recipe, quantity
and food.
Next time, set lower or higher values.
▶
Tip: A lot of information about the food preparation and corresponding set-
ting values can be found on our website www.siemens-home.bsh-group.com .
WARNING ‒ Risk of electric shock!
When changing the bulb, the bulb socket contacts are
live.
Before replacing the bulb, ensure that the appliance
▶
is switched off in order to prevent a potential electric
shock.
Also unplug the appliance from the mains or switch
▶
off the circuit breaker in the fuse box.
Requirements
¡ The appliance is disconnected from the power sup-
ply.
¡ The cooking compartment has cooled down.
¡ You have a new halogen bulb to replace the old one.
Place a tea towel in the cooking compartment to
1.
prevent damage.
Turn the glass cover anti-clockwise to remove it .
2.
first.
Advertisement
Table of Contents
