Table of Contents
Advertisement
Quick Links
Printed Matter No. 9839 0484 01
Publication Date 2020-06-30
Valid from Serial No. C9810001
G2412-1
(20000 r/min)
(20000 rpm)
Read all safety warnings and instructions
Failure to follow the safety warnings and instructions may result in
electric shock, fire and/or serious injury.
Save all warnings and instructions for future reference
8423031221
WARNING
G2412-1
Product Instructions
Die grinder
Advertisement
Table of Contents
Related Manuals for Atlas Copco G2412-1
Summary of Contents for Atlas Copco G2412-1
- Page 1 G2412-1 Printed Matter No. 9839 0484 01 Die grinder Publication Date 2020-06-30 Valid from Serial No. C9810001 Product Instructions G2412-1 8423031221 (20000 r/min) (20000 rpm) WARNING Read all safety warnings and instructions Failure to follow the safety warnings and instructions may result in electric shock, fire and/or serious injury.
- Page 2 G2412-1 © Atlas Copco Industrial Technique AB - 9839 0484 01...
-
Page 3: Table Of Contents
Replacement of vanes................. 13 Lubrication instructions ................... 13 Rust protection and cleaning ............... 13 Lubrication ................... 13 Lubricating guide ................. 14 Dismantling/Assembling instructions .............. 14 Instructions for complete tool............... 14 Instructions for vane motor .............. 15 Testing ...................... 17 © Atlas Copco Industrial Technique AB - 9839 0484 01... - Page 4 Recycling ....................... 18 Recycling instruction.................. 18 © Atlas Copco Industrial Technique AB - 9839 0484 01...
-
Page 5: Product Information
■ Damage to parts that occurs as a result of inadequate maintenance or performed by parties other than Atlas Copco or their Certified Service Partners during the warranty period is not covered by the warranty. ■ To avoid damage or destruction of tool parts, service the tool according to the recommended mainte- nance schedules and follow the correct instructions. -
Page 6: Website
You can find information concerning our products, accessories, spare parts and published matters on our website. Safety Data Sheets MSDS/SDS The safety data sheets describes chemical products sold by Atlas Copco. For more information, consult the website: www.atlascopco.com/sds Country of origin Please refer to the information on the product label. -
Page 7: Service Overview
If the product is not working properly, take it out of service and inspect it. If no detailed information about preventive maintenance is included, follow these general guidelines: ■ Clean appropriate parts accurately ■ Replace any defective or worn parts © Atlas Copco Industrial Technique AB - 9839 0484 01... -
Page 8: Installation
Air quality ■ For optimum performance and maximum product life we recommend the use of compressed air with a maximum dew point of +10°C (50°F). We also recommend to install an Atlas Copco refrigeration type air dryer. ■ Use a separate air filter which removes solid particles larger than 30 microns and more than 90% of liquid water. -
Page 9: Installation Of Vibrating Tools
Look for any damages or oil leakage that can compromise the safety of the tool. Installation of vibrating tools We recommend using a minimum length of 300 mm (12") of flexible hose for compressed air between a vi- brating tool and the quick-action coupling. © Atlas Copco Industrial Technique AB - 9839 0484 01... -
Page 10: Operation
■ Use a pressure regulator to prevent a too high air pressure which can cause overspeed. ■ Make sure that connections and the air hose are in good condition. © Atlas Copco Industrial Technique AB - 9839 0484 01... -
Page 11: Operating Instructions
Always shut off the air supply, drain hose of air pressure and disconnect the tool from air supply; ► when not in use, before making any adjustments to the product - for example changing acces- sories, or when making repairs. © Atlas Copco Industrial Technique AB - 9839 0484 01... - Page 12 Do a test run of every new mounted wheel in a safe position for 30 seconds. Use a barrier such as under a heavy work table to stop any possible broken wheel parts. Stop immediately if the vibration is excessive. © Atlas Copco Industrial Technique AB - 9839 0484 01...
-
Page 13: Service
For flexible spindle extension – When fitting the extended spindle – apply 0.5 cm (0.03 cu in) of grease type “Lubricating Engineers LE3752” (or EP grease) at the bottom of the hole in the collet holder. © Atlas Copco Industrial Technique AB - 9839 0484 01... -
Page 14: Lubricating Guide
Castrol Spheerol EP L2 Esso Beacon EP2 Rembrandt EP2 Mobil Mobilegrease XHP 222 Shell Alvania EP2 Texaco Multifak EP2 Molycote BR2 Plus Dismantling/Assembling instructions Instructions for complete tool Dismantling Inspection © Atlas Copco Industrial Technique AB - 9839 0484 01... -
Page 15: Instructions For Vane Motor
PTFE-particles must not come in contact with open fire, glow or heat ► Motor components must be washed with cleaning fluid and not blown clear with an air line ► Wash your hands before starting any other activity ► © Atlas Copco Industrial Technique AB - 9839 0484 01... - Page 16 4080 0182 09 17.5 4080 0182 10 20.5 4080 0182 11 25.5 4080 0182 12 30.5 4080 0182 13 35.5 4080 0182 14 40.5 Dismantling tool Mandrel A Inspection of motor parts © Atlas Copco Industrial Technique AB - 9839 0484 01...
-
Page 17: Testing
4080 0567 03 21.5 4080 0567 07 25.5 10.5 4080 0567 08 27.5 12.5 4080 0567 09 31.5 15.5 4080 0567 10 34.5 18.5 Dismantling tool Mandrel B E: Ball bearing Testing © Atlas Copco Industrial Technique AB - 9839 0484 01... - Page 18 When a product has served its purpose it has to be recycled properly. Dismantle the product and recycle the components in accordance with local legislation. Batteries shall be taken care of by your national battery recovery organization. © Atlas Copco Industrial Technique AB - 9839 0484 01...
- Page 20 Original instructions © Copyright 2020, Atlas Copco Industrial Technique AB. All rights reserved. Any unauthorized use or copying of the contents or part thereof is prohibited. Atlas Copco Industrial This applies in particular to trademarks, model denominations, part numbers Technique AB and drawings.
Need help?
Do you have a question about the G2412-1 and is the answer not in the manual?
Questions and answers