Download Print this page

TriangleTube PSRKIT65 Manual

Prestige solo 110 and excellence natural to lp conversion

Advertisement

Quick Links

Prestige SOLO 110 and EXCELLENCE
Natural to LP Conversion
Kit Part Numbers: PSRKIT65
Parts List
1. Burner Head - KNIT Style
2. Burner Head Gasket
3. Stainless Steel Phillips Screws. (For attaching the
new burner head to the burner mounting plate.)
4. PS 110 LP Orifice 0.203
5. T-25 Torx Wrench
6. Conversion Label
7. Rating Label
8. Combustion Chamber Insulation
9. Insulation Alignment Tool
Recommended tools:
A. Pipe Wrench.
B. Phillips Screw Driver.
C. 10 mm Socket and/or 10 mm Open Ended
Wrench and/or Adjustable Wrench.
D. Flat Blade Putty Knife.
W RNING
Indicates a potentially hazardous situation
which, if ignored, can result in serious
injury or substantial property damage.
W RNING
For your safety, turn off electrical power
supply at service panel and allow unit to cool
before proceeding. Failure to do so can cause
severe personal injury or death.
NOTI E
Indicates special instructions on installa-
tion, operation or maintenance, which are
important to equipment but not related to
personal injury hazards.
W RNING
Failure to follow instructions below can
result in severe personal injury or damage if
ignored.
Instructions are for a qualified installer/
service technician.
Read all instructions before proceeding.
Follow instructions in proper order.

Advertisement

loading
Need help?

Need help?

Do you have a question about the PSRKIT65 and is the answer not in the manual?

Questions and answers

Summary of Contents for TriangleTube PSRKIT65

  • Page 1 Prestige SOLO 110 and EXCELLENCE Natural to LP Conversion Kit Part Numbers: PSRKIT65 Parts List 1. Burner Head - KNIT Style 2. Burner Head Gasket 3. Stainless Steel Phillips Screws. (For attaching the new burner head to the burner mounting plate.) 4.
  • Page 2 Prestige SOLO 110 and EXCELLENCE Natural to LP Conversion Instructions: 11. Remove the 10 mm nuts and remove the burn- er mounting plate assembly from the heat 1. Turn power to the unit “OFF” and allow unit to exchanger body. cool.
  • Page 3 Prestige SOLO 110 and EXCELLENCE Natural to LP Conversion W RNING Failure to retain the rubber orifice gasket on the gas valve will cause an improper seal between the gas valve and the venturi resulting in a potential gas Burner Mounting Plate leak.
  • Page 4 Prestige SOLO 110 and EXCELLENCE Natural to LP Conversion 24. Re-attach the ignition cable (MCBA) and the ground wire to the ignitor. 25. Reattach the air inlet elbow to the venturi. 26. Reposition the control panel. 27. Replace the front jacket panel and secure with the thumb screw on the upper edge of the unit.
  • Page 5 Prestige SOLO 110 and EXCELLENCE Natural to LP Conversion MCBA Instructions O 2 increases and CO 2 decreases 1. Manually place the boiler into high fire mode Clockwise adjustment of OFFSET SCREW at by pressing the MODE button with “+” button Low Fire: simultaneously on the control panel display O 2 decreases and CO 2 increases...
  • Page 6 Prestige SOLO 110 and EXCELLENCE Natural to LP Conversion 3. Press the RIGHT button to highlight the 7. Once the combustion level is set at high fire, then press the OK Manual Operation icon manually place the boiler into low fire mode by button.
  • Page 7 Prestige SOLO 110 and EXCELLENCE Natural to LP Conversion Handling of Previously Fired Combustion Chamber Insulation 1-800-356-4676 www.cdc.gov/niosh for latest recommendations. W RNING 2. Wear long sleeved, loose fitting clothing, The combustion chamber insulation con- gloves and eyes protection. tains ceramic fibers, which are classified as 3.