Table of Contents
Advertisement
Quick Links
Prestige SOLO 399
Burner Mounting Plate Kit
Kit Part Numbers: PSRKIT39
Parts List
1. Burner Plate
2. Burner Plate Gasket
3. Sight Glass Assembly
4. Igniter (MCBA)
5. Igniter (TriMax)
6. Burner Head Gasket
7. Blower Gasket
8. Combustion Chamber Insulation
9. Insulation Alignment Tool
10. Gas Pipe Gasket
Recommended tools:
A. Pipe Wrench.
B. Phillips Screw Driver.
C. 10 mm Socket and/or 10 mm Open Ended
Wrench and/or Adjustable Wrench.
D. Flat Blade Putty Knife.
W RNING
Indicates a potentially hazardous situation
which, if ignored, can result in serious
injury or substantial property damage.
W RNING
For your safety, turn off electrical power
supply at service panel and allow unit to cool
before proceeding. Failure to do so can cause
severe personal injury or death.
NOTI E
Indicates special instructions on installa-
tion, operation or maintenance, which are
important to equipment but not related to
personal injury hazards.
W RNING
Failure to follow instructions below can
result in severe personal injury or damage if
ignored.
•
Instructions are for a qualified installer/
service technician.
•
Read all instructions before proceeding.
•
Follow instructions in proper order.
Advertisement
Table of Contents
Related Manuals for TriangleTube PSRKIT39
Summary of Contents for TriangleTube PSRKIT39
- Page 1 Prestige SOLO 399 Burner Mounting Plate Kit Kit Part Numbers: PSRKIT39 Parts List 1. Burner Plate 2. Burner Plate Gasket 3. Sight Glass Assembly 4. Igniter (MCBA) 5. Igniter (TriMax) 6. Burner Head Gasket 7. Blower Gasket 8. Combustion Chamber Insulation 9.
- Page 2 Prestige SOLO 399 Burner Mounting Plate Kit Instructions: 12. Remove the combustion chamber insulation from the heat exchanger. See WARNING on 1. Turn power to the unit “OFF” and allow unit to page 7. cool. 2. Shut off gas supply to the inlet of the unit at the main manual shutoff valve to the unit.
- Page 3 Prestige SOLO 399 Burner Mounting Plate Kit 17. Install new burner plate gasket onto heat exchanger. Burner Mounting Plate Fig. 4: Combustion Chamber Insulation Installation 19. Check combustion chamber insulation alignment with the burner mounting plate. The combustion Burner chamber insulation igniter cutout should align Head Burner Head Gasket...
- Page 4 Prestige SOLO 399 Burner Mounting Plate Kit 30. Turn power to the unit “ON”. The unit is now ready to be placed back into service. W RNING Do not check for gas leaks with an open flame. COMBUSTION TEST/ADJUSTMENT Use a bubble test. Failure to check for gas leaks can cause severe personal injury, death The installer must perform a complete combustion or substantial property damage.
- Page 5 Prestige SOLO 399 Burner Mounting Plate Kit 5. Press the “+” and “-” buttons simultaneously to NOTI E shutdown the burner. The control panel will display a H followed by the current boiler temperature when TriMax Instructions placed into high fire test mode. 1.
- Page 6 Prestige SOLO 399 Burner Mounting Plate Kit 5. Press the RIGHT button to adjust the firing rate Counter-clockwise adjustment of OFFSET to 100% (high fire). Hold down the RIGHT SCREW at Low Fire (1% firing rate): button to rapidly increase the firing rate. O 2 increases and CO 2 decreases 6.
- Page 7 Prestige SOLO 399 Burner Mounting Plate Kit Handling of Previously Fired Combustion Chamber Insulation 1-800-356-4676 W RNING www.cdc.gov/niosh for latest recommendations. 2. Wear long sleeved, loose fitting clothing, The combustion chamber insulation con- gloves and eyes protection. tains ceramic fibers, which are classified as 3.
Need help?
Do you have a question about the PSRKIT39 and is the answer not in the manual?
Questions and answers