Safety Instructions - U.S.SAWS CORE EZ Operating Manual

4.0

SAFETY INSTRUCTIONS

4.1 KNOW THE RULES & YOUR EQUIPMENT.
Most job sites have rules governing equipment use & maintenance.
Before starting at a new work location, check with the supervisor or
safety coordinator. Ask about any rules or regulations you need to
abide.
OSHA enforces federal laws within the United States that apply to the
safe operation, application, & maintenance of equipment on job sites.
It is the employer's responsibility to comply with these laws.
Do not operate this machine unless you have read the operations and
maintenance manual carefully.
4.2 RECEIVE PROPER TRAINING.
Do not operate this machine unless you have received operational and
maintenance training from a U.S. SAWS representative or from an autho-
rized distributor for U.S.SAWS.
4.3 PROTECT YOUR FEET.
Observe all applicable local, state and federal safety regulations. Wear
OSHA approved foot protection.
4.4 PROTECT YOUR EYES.
Observe all applicable local, state and federal safety regulations. Wear
OSHA approved safety glasses.
4.5 PROTECT YOUR HEARING.
Observe all applicable local, state and federal safety regulations. Wear
OSHA approved hearing protection.
4.6 DRESS PROPERLY.
Do not wear loose clothing or jewelry that can be caught in moving parts.
Wear protective hair covering to contain long hair. Keep hair away from
motor air vent. Rubber gloves and non-skid footwear are recommended
when working outdoors.
4.7 AVOID A DANGEROUS ENVIRONMENT.
Do not expose machine to rain. Do not use machine in wet conditions.
Water entering a power tool will increase the risk of electric shock. Keep
work area well lit. When working at an elevated location, pay attention to
articles and persons below. If operating the power tool in damp locations
is unavoidable, use a Ground Fault Circuit Interrupter (GFCI) protected
supply. Use of an GFCI reduce the risk of electric shock.
4.8 AVOID ANY AREAS OR ACTIONS THAT EXPOSE YOU TO CAR-
BON MONOXIDE.
Exhaust gas from gasoline engines contains dangerous carbon monox-
ide. Breathing it can cause unconsciousness and even kill you. Always
operate gasoline engine machines in a well-ventilated area. Do not
operate in areas where exhaust fumes could accumulate without wear-
ing appropriate respiratory protection. Consult your employer and OSHA
regarding use of appropriate respirator for dangerous carbon monoxide
gases.
4.9 KEEP WORK AREA CLEAN. DO NOT RUN OVER ANYTHING.
Loose objects could be thrown from crack. Make sure area to be cut is
clear from people and any loose objects, nuts, bolts, etc. Never run over
any loose objects.
S A F E T Y I N S T R U C T I O N S
Waterworks
Division
4.10 KEEP CHILDREN AND VISITORS AWAY.
Do not allow anyone to stand in line with the blade path. Do not let children
or visitors contact machine or extension cord. Keep children and visitors
away from the work area.
4.11 KEEP FIRM GRIP ON MACHINE.
During normal operation as instructed in Section 6.0, keep a firm hold
on the handle grips and maintain control of the machine until the blade
completely stops.
4.12 SHUT OFF MACHINE.
When not in use, before servicing and when changing accessories shut off
engine. Release the lever switch and move the on/off switch to the OFF
position. Move the fuel valve lever to the OFF position.
4.13 STORE IDLE EQUIPMENT.
The machine and tools should be stored in a dry and secure location when
not in use. Keep equipment out of reach of children.
4.14 DO NOT OVERREACH.
Keep proper footing and balance at all times.
4.15 OBTAIN MATERIAL SAFETY DATA SHEET (MSDS) FOR
ALL WORK SURFACE MATERIALS.
This includes primers, all coatings, adhesives, tile and crack filling materi-
als, etc. Do not attempt to cut, clean out or remove material without MSDS
information. Consult MSDS sheet for hazards information. Be aware that
some materials are explosive as a dust.
4.16 MAINTAIN MACHINE WITH CARE.
Keep machine clean and follow maintenance procedures for better and
safer performance. Keep handles dry, clean, and free from oil and grease.
Follow instructions for lubricating and changing accessories.
4.17 REMOVE ADJUSTING TOOLS.
Form a habit of checking to see that tools such as adjusting wrenches are
removed from the machine and properly stored before starting the engine.
4.18 STAY ALERT.
Watch what you are doing. Use common sense. Do not operate machine
when you are tired or fatigued.
4.19 DO NOT USE DRUGS, ALCOHOL, MEDICATION.
Do not operate machine while under the influence of drugs, alcohol,
or any medication.
4.20 KEEP THE RIGHT PARTS IN THE RIGHT POSITIONS.
Do not operate machine with parts missing or improperly mounted.
4.21 CHECK DAMAGED PARTS.
Verify all machine guards are in good condition and will function properly
before using the machine. Check for alignment of moving parts, binding of
moving parts, breakage of parts, mounting, and any other conditions that
may affect machine operation. A guard, power switch or other part that is
damaged should be properly repaired or replaced by an authorized service
center unless indicated elsewhere in this instruction manual. Do not oper-
ate machine if lever or engine on/off switch does not function properly.
P: 866 987-7297 F: 813-621-7125
Visit us at www.ussaws.com
sales@ussaws.com
4