Page 1
U.S.SAWS CORE EZ OPERATING MANUAL Notice of Copyright Protection Copyright 2020, by U.S.SAWS . All rights reserved. This work may not be reproduced or disseminated in whole or in part by any means without the prior written permission of U.S.SAWS 08-29-2023...
The U.S.SAWS Core EZ Core® makes core drilling easy by utilizing standard 110 V power. U.S.SAWS Core EZ offers a new way of core drilling. The entire unit and a selection of bits fit into a wheeled case that weighs under 50...
You must clearly understand the written instructions supplied measures. by U.S.SAWS, be trained - including actual operation - & know the safety rules & regulations for the job site. It is a safety practice to point out & ex- plain safety signs &...
Do not operate this machine unless you have received operational and 4.13 STORE IDLE EQUIPMENT. maintenance training from a U.S.SAWS representative or from an autho- The machine and tools should be stored in a dry and secure location when rized distributor for U.S.SAWS.
Page 5
S A F E T Y I N S T R U C T I O N S 4.22 SECURELY MOUNT ACCESSORIES TO THE MACHINE. Extra care must be taken an elevated location to prevent injury to some- one on a lower level in the event the tool or accessory should drop. Do not operate without fall protection for operator and debris protection for public.
P R E-O P E R AT I O N U.S.SAWS Core EZ is a battery-operated, portable, and powerful core drilling machine and the most versatile and complete unit available to-date. Core EZ in Storage Case Water Feed Tube Carry Case...
O P E R AT I O N Remove nuts from anchor bolt. WARNING: Always insure that the switch is in the “OFF” position before plugging the unit into electrical power. CAUTION: Never leave the drill running unattended. Turn power off when not in use.
Page 8
O P E R AT I O N 6.10 To mount water feed tube, slide it over the guide post and thread the feed nut while aligning the mounting plate bolts on the back of the gearbox. WARNING: Do not over reach, maintain control. Keep proper footing and balance at all times.
Page 9
O P E R AT I O N Vertical Drilling Floors WARNING: Do not over reach, maintain control. Keep proper footing and balance at all times. Maintain a firm grip. Use extra care using the tool on ladders, roofs, scaffolds, etc. 6.10 DISASSEMBLY STEPS 6.10.1...
Page 10
PA R T S Core EZ Number Description Part Number Water Feed Tube US28172 Grinder Coupler US28591-8 Guide Post US28152 Spring Locking Pin US28191-8 Spindle Nut 5/8-”11 US28191-6 Core Mate Gear Box US28181 Hex Core Bit Adapter US28561 Metabo Grinder with Adapter Assy for CoreEZ US28181 Core EZ 3-tab Feed Tube Adapter with Clear Anodize US28171-23...
Page 11
PA R T S Gearbox Number Description Part Number Gearbox Top Housing US28581-1 Reverse Idler Pulley (29 mm) US28141-16 Polychain Belt 425-25 US28131-16 Input Shaft US28111 Intermediate Shaft US28121 Polychain Belt 425-15 US28111-11 Reverse Idler Pulley (20 mm) US28141-15 Hex Output Shaft US28131 Gearbox Bottom Housing US28581-2...
Page 12
PA R T S Gearbox Number Description Part Number Feed tube insert US28171-22 Feed screw 16.375” US28172-1 Al feed tube US28172-3 Feed tube adapter US28571-8 (2) Hose clamp SX27607 3/8 blue hose - 12” US27610 Barbed hose fitting male US27611 Brass barbed hose fitting female US27612 3/4”...
Warranty This document is to be used as a guide in determining warranty policies and procedures for U.S.SAWS and its U.S.SAWS products. It is to be used in determining whether a warranty is justified and as a procedural guide in completing a U.S.SAWS warranty claim form.
Page 15
FILL OUT THE ATTACHED CARD COMPLETELY AND ACCURATELY. WARRANTY REGISTRATION CARD IMPORTANT! To ensure that your U.S.SAWS machine is covered under warranty, please fill in the following information and mail or fax it to U.S.SAWS, 8004B E. Broadway Ave. Tampa, FL 33619, Fax No. (813) 621-7125...