Page 1
PROTECTIVE GLASSES OR FULL FACE PROTECTION Notice of Copyright Protection Copyright 2020, by U.S.SAWS . All rights reserved. This work may not be reproduced or disseminated in whole or in part by any means without the prior written permission of U.S.SAWS...
50 Part Number US28000 pounds. The Core EZ drills holes from 3 into 10 in with ease. The entire unit Capacity 3”-10” Core Bits is mounted on a central guide shaft rigidly anchored to the wall that...
You must clearly understand the written instructions supplied measures. by U.S.SAWS, be trained - including actual operation - & know the safety rules & regulations for the job site. It is a safety practice to point out & ex- plain safety signs &...
U.S. SAWS representative or from an autho- The machine and tools should be stored in a dry and secure location when rized distributor for U.S.SAWS. not in use. Keep equipment out of reach of children. PROTECT YOUR FEET.
Page 5
REFER TO METABO MANUAL defects or other reproductive harm. Refer to 36v Battery Operated Metabo 36LTX Grinder Owner’s Manual included with your Core EZ kit for operations,maintenance and safety gudelines. This tool creates an enormous amount of force. Beware of crushing your fingers or other body parts.
P R E-O P E R AT I O N U.S.SAWS Core EZ ) is a battery-operated, por- table, and powerful core drilling machine and the most versatile and complete unit available to-date. Core EZ in Storage Case Water Feed Tube...
O P E R AT I O N Remove nuts from anchor bolt. WARNING: Always insure that the switch is in the “OFF” position before plugging the unit into electrical power. CAUTION: Never leave the drill running unattended. Turn power off when not in use.
Page 8
O P E R AT I O N 6.10 To mount water feed tube, slide it over the guide post and thread the feed nut while aligning the mounting plate bolts on the back of the gearbox. WARNING: Do not over reach, maintain control. Keep proper footing and balance at all times.
Page 9
O P E R AT I O N Vertical Drilling Floors WARNING: Do not over reach, maintain control. Keep proper footing and balance at all times. Maintain a firm grip. Use extra care using the tool on ladders, roofs, scaffolds, etc. 6.10 DISASSEMBLY STEPS 6.10.1...
Page 10
PA R T S Core Mate Number Description Part Number Water Feed Tube US28172 Grinder Coupler US28591-8 Guide Post US28152 Spring Locking Pin US28191-8 Spindle Nut 5/8-”11 US28191-6 Core Mate Gear Box US28581 Hex Core Bit Adapter US28161 P: 866 987-7297 F: 813-621-7125 Waterworks Visit us at www.ussaws.com Division...
Page 11
PA R T S Gearbox Number Description Part Number Gearbox Top Housing US28581-1 Reverse Idler Pulley (29 mm) US28141-16 Polychain Belt 425-25 US28111-11 Input Shaft US28111 Intermediate Shaft US28121 Polychain Belt 425-15 US28131-16 Reverse Idler Pulley (20 mm) US28141-15 Hex Output Shaft US28131 Gearbox Bottom Housing US28581-2...
R E L AT E D P R O D U C T S & A C C E S S O R I E S Water Tank Catch Flanges Part No Varies by size Part No US27810-1 Description Flange set for use in vertical drilling Description 3.5 gallon manual water pump applications to hold machine.
Warranty This document is to be used as a guide in determining warranty policies and procedures for U.S.SAWS and its U.S.SAWS products. It is to be used in determining whether a warranty is justified and as a procedural guide in completing a U.S.SAWS warranty claim form.
Page 14
FILL OUT THE ATTACHED CARD COMPLETELY AND ACCURATELY. WARRANTY REGISTRATION CARD IMPORTANT! To ensure that your U.S.SAWS machine is covered under warranty, please fill in the following information and mail or fax it to U.S.SAWS, 8004B E. Broadway Ave. Tampa, FL 33619, Fax No. (813) 621-7125...