Lifetime PUMP ADJUST 90602 Assembly Instructions Manual
  1. Manuals
  2. Brands
  3. Lifetime Manuals
  4. Sports & Outdoors
  5. PUMP ADJUST 90602
  6. Assembly instructions manual

Lifetime PUMP ADJUST 90602 Assembly Instructions Manual

Basketball system
Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
PUMP ADJUST
BASKETBALL SYSTEM
MODEL 90602
BEFORE ASSEMBLY:
• Before you start, decide how you would like to fi ll
your base (sand is recommended).
• Assembly should take 3 people about 3-4
hours to complete.
Save this instruction in the event that the manufacturer has
to be contacted for replacement parts.
TOOLS REQUIRED
1/2" (13 mm)
9/16" (14 mm)
(x2)
(x2)
1/2" (13 mm)
(x1)
(x1)
30" Rebar
Level
QUESTIONS?
CONTACT LIFETIME CUSTOMER SERVICE:
Call: 1-800-225-3865
7:00 am-5:00 pm (Monday-Friday) MST
and 9:00 am-1:00 pm Saturday MST
®
11/16" (18 mm)
(x2)
(x1)
Cement Mix
(x1)
Live Chat:
www.lifetime.com
ASSEMBLY INSTRUCTIONS
3/4" (19 mm)
1/2" (13 mm)
(x2)
(x1)
(x1)
(x1)
(x3)
For Customer Service in Mainland
Europe and the United Kingdom,
E-mail: cs@lifetimeproducts.eu

TABLE OF CONTENTS

Icon Legend................................2
Notices....................................3
Ground Preparation.....................4
(x2)
Pole Assembly.............................8
(x1)
Handle Assembly......................23
Final Assembly..........................32
Maintenance Instructions..........36
Warning Sticker........................37
Registration........................38
Warranty................................39
Model Number: 90602
Product ID:

Advertisement

Table of Contents
loading

Related Manuals for Lifetime PUMP ADJUST 90602

Summary of Contents for Lifetime PUMP ADJUST 90602

  • Page 1: Table Of Contents

    Registration......38 (x1) Level Warranty........39 (x1) (x1) (x3) Model Number: 90602 QUESTIONS? CONTACT LIFETIME CUSTOMER SERVICE: Product ID: Call: 1-800-225-3865 Live Chat: For Customer Service in Mainland Europe and the United Kingdom, www.lifetime.com 7:00 am–5:00 pm (Monday–Friday) MST E-mail: cs@lifetimeproducts.eu and 9:00 am–1:00 pm Saturday MST...

  • Page 2: Icon Legend

    ICON LEGEND • Indicates special heed should be taken when reading. • Indicates the parts to be used for a section. • Indicates no parts required for a specifi c section. • Indicates the hardware to be used for a section. •...

  • Page 3: Notices

    WARNINGS & NOTICES SAFETY INSTRUCTIONS FAILURE TO FOLLOW THESE WARNINGS MAY RESULT IN SERIOUS INJURY OR PROPERTY DAMAGE AND WILL VOID WARRANTY. Owner must ensure that all players know and follow these rules for safe operation of the system. To ensure safety, do not attempt to assemble this product without following the instructions carefully. Check entire box and inside all packing material for parts and/or additional instruction material.

  • Page 4: Ground Preparation

    GROUND PREPARATION HARDWARE REQUIRED PARTS REQUIRED Metal Parts ALE (x1) Paper Parts BGW (x1) TOOLS REQUIRED 30" Rebar Level 640 lb / 291 kg...
  • Page 5 SECTION 1 (CONTINUED) TOOLS AND HARDWARE REQUIRED 640 lb / 291 kg • Dig a round hole 24" deep and 21" in diameter. If you live in an area where frost heaves may pose a problem, consult your local building inspector to determine the proper hole depth.
  • Page 6 SECTION 1 (CONTINUED) TOOLS AND HARDWARE REQUIRED 30" Rebar • Slide the dimpled end of the Bottom Pole (ALE) into the cement up to the 16-inch mark. Position the pole next to the playing surface. For regulation courts, the Alignment Frame (BGW) should cross the playing surface at the middle of the scored measurements.
  • Page 7 SECTION 1 (CONTINUED) TOOLS AND HARDWARE REQUIRED • Mix the remaining 1/2 bag of concrete. Fill the Bottom Pole (ALE) with concrete until it reaches the top of the rebar (about 15" from the top of the pole). Tamp the concrete down in the Bottom Pole with a broom handle to remove air pockets.

  • Page 8: Pole Assembly

    POLE ASSEMBLY HARDWARE REQUIRED Hardware Bag 5” ANF (x2) AAA (x2) AAF (x2) CMV (x2)* ANE (x2) • Only one Self-Drilling Screw (CMV) will be used in Section 2. Save the second Screw for use in Section 5. PARTS REQUIRED Metal Parts ALH (x1) ALL (x1)
  • Page 9 Son mécanisme a été conçu uniquement pour soutenir le poids du panneau et de l’anneau. N’accrochez rien au manche, à l’anneau, au panneau ni aux leviers sous peine d’endommager l’équipement et d’annuler la garantie. Lifetime Products, Inc., Clearfield, UT 84016 www.lifetime.com 1-800-225-3865 7/12/2016...
  • Page 10 SECTION 2 (CONTINUED) TOOLS AND HARDWARE REQUIRED CMV (x1) • THIS STEP CANNOT BE REVERSED! Strike the end of the Pole Assembly on a piece of scrap wood or cardboard fi ve to six times. • Do not hit your feet with the Pole sections, as serious injury could occur.

  • Page 11: Backboard To Rim Assembly

    BACKBOARD TO RIM ASSEMBLY HARDWARE REQUIRED Hardware Bag 5 9/16” ANM (x2) ANL (x1) ANN (x2) ANJ (x4) ADX (x2) BGZ (x1) ANK (x4) ABB (x2) ABK (x4) AAX (x1) ANO (x1) ABD (x4) PARTS REQUIRED Metal Parts BPZ (x1) AJI (x1) BQA (x1) BGY (x1)
  • Page 12 SECTION 3 (CONTINUED) TOOLS AND HARDWARE REQUIRED 9/16" (14 mm) (x2) ANJ (x2) ABK (x2) ABD (x2) • Lay the Backboard (AJI) face up with the Rim holes exposed over the edge of a table. Place the Rim Impact Spacer (BGY) in the Backboard.
  • Page 13 SECTION 3 (CONTINUED) TOOLS AND HARDWARE REQUIRED 5 9/16” 1/2" (13 mm) (x2) 3/4" (19 mm) ANJ (x2) ANL (x1) ABD (x2) AAX (x1) (x2) ABK (x2) ANK (x2) • Secure the Rim Adapter Plate (ALY) to the Backboard (AJI) by using the hardware as shown. •...
  • Page 14 SECTION 3 (CONTINUED) TOOLS AND HARDWARE REQUIRED 9/16" (14 mm) (x2) ANM (x2) ABB (x2) ANK (x2) • Slide the Spring Holder Clevis (AMK) onto the Eye Bolt (BQA) and secure with the hardware shown.
  • Page 15 SECTION 3 (CONTINUED) TOOLS AND HARDWARE REQUIRED 9/16" (14 mm) (x2) ADX (x2) BGZ (x1) ANN (x2) (x1) ANO (x1) • Slide the Compression Spring (BGZ) onto the Eye Bolt (BQA), and secure with the hardware shown. Tighten the 3/8” Zinc Nuts (ANN) to adjust Rim tension.

  • Page 16: Backboard To Pole Assembly

    BACKBOARD TO POLE ASSEMBLY HARDWARE REQUIRED Hardware Bag 7 1/16” (18 cm) AQB (x2) ANU (x2) AAD (x1) 5” ANQ (x2) AQD (x1) ANS (x8) ANP (x1) AAX (x4) ABN (x4) AOR (x6) AAN (x2) ABP (x2) ANK (x4) ANZ (x2) PARTS REQUIRED Metal Parts Plastic Parts...
  • Page 17 SECTION 4 (CONTINUED) TOOLS AND HARDWARE REQUIRED 1/2” (13mm) (x1) AQB (x2) AAN (x2) 1/2” (13 mm) (x1) • Insert one end of the Tie Plate (BLC) into the slot on the Lower Extension Arm (BGP), then iInsert the opposite end of the Tie Plate (BLC) into the slot on the other Lower Extension Arm (BGP) as shown.
  • Page 18 SECTION 4 (CONTINUED) SECTION 4 (CONTINUED) TOOLS AND HARDWARE REQUIRED TOOLS AND HARDWARE REQUIRED / HERRAMIENTAS Y ACCESORIOS REQUERIDOS / OUTILS ET ACCESSOIRES REQUIS 7 1/16” (18 cm) 3/4" (19 mm) (x2) AAD (x1) ANZ (x2) AAX (x1) AOR (x2) •...
  • Page 19 SECTION 4 (CONTINUED) TOOLS AND HARDWARE REQUIRED 5” 3/4" (19 mm) (x2) AQD (x1) (x1) ABN (x2) AAX (x1) ANK (x2) • Insert the Pole Cap (ALM) into the Top Pole as shown. Line up the Pole Cap stirrups with the holes in the top of the Pole. •...
  • Page 20 SECTION 4 (CONTINUED) TOOLS AND HARDWARE REQUIRED 3/4" (19 mm) (x2) ANQ (x2) 11/16" (18 mm) ABP (x2) (x1) AOR (x2) ANP (x1) (x1) • Rest the Rim on cardboard to prevent scratching, then secure the Lower Extension Arms (BGP) to the Backboard (AJI) with the hardware shown.

  • Page 21: Parts Identifier

    PARTS IDENTIFIER This page intentionally left blank...
  • Page 22 PARTS IDENTIFIER Metal Parts ALE (x1) ALL (x1) ALH (x1) ALX (x1) ALF (x1) • Warning Sticker applied to side not shown CMR (x2) BGO (x2) CKJ (x1) BGP (x2) 31” CKM (x2) ALS (x2) Metal Parts found in Rim Kit BPZ (x1) AMK (x1) AMA (x1)
  • Page 23 PARTS IDENTIFIER Plastic Parts AKF (x1) AKG (x1) AKP (x1) AJI (x1) CKH (x1) ALM (x1) CKI (x1) BGW (x1) AQC (x2) AKZ (x1) CKG (x2) HARDWARE REQUIRED...
  • Page 24 PARTS IDENTIFIER This page intentionally left blank...
  • Page 25 SECTION 4 (CONTINUED) TOOLS AND HARDWARE REQUIRED 3/4" (19 mm) (x2) ANU (x2) (x1) AAX (x2) ABN (x2) AOR (x2) ANK (x2) • Attach the Upper Extension Arms (BGO) to the Backboard (AJI) with the hardware as shown. • Tighten the Nuts until they are fl...
  • Page 26 SECTION 4 (CONTINUED) TOOLS AND HARDWARE REQUIRED ANS (x8) • Insert Nylon Plugs (ANS) into the locations indicated on the frame of the Backboard.

  • Page 27: Handle Assembly

    HANDLE ASSEMBLY HARDWARE REQUIRED Hardware Bag 6” ACX (x1) CKW (x1) ANK (x2) 7 1/16” (18 cm) FHM (x1) AAD (x1) BFI (x1) ABB (x1) 6 1/2” (18.5 cm) AAX (x3) AAW (x2) ANZ (x3) ABN (x4) CKX (x2) CKV (x2) ADT (x7) AOR (x2) AAO (x1)
  • Page 28 HANDLE ASSEMBLY PARTS REQUIRED Metal Part / Pieza de metal Pièce en métal 31” ALS (x2) CKM (x2) CMR (x2) CKJ (x1) Plastic Parts/ Piezas de plástico Pièces en plastique AKF (x1) AKG (x1) CKG (x2) CKI (x1) CKH (x1) TOOLS REQUIRED 7/16"...
  • Page 29 SECTION 5 (CONTINUED) TOOLS AND HARDWARE REQUIRED 1/2" (13 mm) ACX (x1) AAO (x1) 7/16" (11 mm) AEB (x2) AAB (x2) 1/4” 1/4” CKZ (x1) • Slide the Gas Spring Cover (AKG) onto the Gas Spring (AKF) as shown. • Align the holes in the Gas Spring Cover (AKG) and the Gas Spring (AKF) with the holes in the Pole Bracket (ALL), and attach the Gas Spring assembly to the Pole Bracket with the hardware shown.
  • Page 30 SECTION 5 (CONTINUED) TOOLS AND HARDWARE REQUIRED 9/16" (14 mm) 6” CKW (x1) BFI (x1) • Slide the Link Cap (CKG) onto the Pump Adjust Link (CKM). Repeat this for the second Link, with the Link Cap fl ipped over. •...
  • Page 31 SECTION 5 (CONTINUED) TOOLS AND HARDWARE REQUIRED 9/16” (14 mm) ADT (x7) FHM (x1) ABB (x1) CKV (x2) • Position the Handle Frame (CKJ) inside of the Top Handle (CKH) and Bottom Handle (CKI) as shown, and secure with the hardware shown.
  • Page 32 SECTION 5 (CONTINUED) TOOLS AND HARDWARE REQUIRED 6 1/2” (18.5 cm) 3/4" (19 mm) AAW (x1) AAX (x1) ANZ (x1) ABN (x2) CKX (x2) • Line up the hardware and spacers shown with the hole nearest to the pole on the Pump Adjust Links (CKM) and the Pump Adjust Actuators (CMR).
  • Page 33 SECTION 5 (CONTINUED) TOOLS AND HARDWARE REQUIRED 7 1/16” (18 cm) 3/4" (19 mm) AAD (x1) ANZ (x2) AAX (x1) AOR (x2) CKT (x1) • Connect the Rear Lifter Arms (ALS) to the inside of the Long Extension Arms (AKB) with the hardware shown. Place a Spacer (CKT) between the Rear Lifter Arms as shown, with a Spacer (ANZ) between the Rear Lifter Arms and the Long Extension Arms on each side.
  • Page 34 SECTION 5 (CONTINUED) TOOLS AND HARDWARE REQUIRED 6 1/2” (18.5 cm) 3/4" (19 mm) AAW (x1) AAX (x1) ANK (x2) ABN (x2) CKU (x2) CKY (x2) 5.10 • Finish connecting the Handle Assembly to the Gas Spring (AKF) with the hardware shown. Make sure to place a Nylon Washer (ANK) between the Gas Spring and the Handle Assembly on each side of the Handle Assembly as shown.
  • Page 35 SECTION 5 (CONTINUED) TOOLS AND HARDWARE REQUIRED AKH (x1) 5.11 • Apply grease from the Grease Packet (AKH) on to the Gas Shock Rod (CKZ).

  • Page 36: Final Assembly

    FINAL ASSEMBLY HARDWARE REQUIRED Hardware Bag CMV (x1) • Hardware used in this Section is taken from the remaining Section 2 hardware. PARTS REQUIRED Plastic Parts AKP (x1) AKZ (x1) TOOLS REQUIRED (x1) (x1) (x1) (x1) (x1) (x3) (not included)
  • Page 37 SECTION 6 (CONTINUED) TOOLS AND HARDWARE REQUIRED • Attach the Net (AKZ) to the Rim (ALX). • BEFORE CONTINUING: It is critical that the instructions in the following steps are followed exactly. Failure to properly orient and align the pole sections will render the pole unusable. If the pole sections are assembled incorrectly, you will have to purchase new pole sections from our Customer Service Department.
  • Page 38 SECTION 6 (CONTINUED) TOOLS AND HARDWARE REQUIRED AT LEAST THREE ADULTS ARE REQUIRED. DO NOT ATTEMPT ASSEMBLY WITH FEWER THAN THREE ADULTS AND THREE LADDERS. (x1) (x3) • Make a mark 5 inches from the top of the Bottom Pole (ALE). With the Backboard facing the playing surface, carefully slide the Top/Middle Pole assembly over the Bottom Pole.
  • Page 39 SECTION 6 (CONTINUED) TOOLS AND HARDWARE REQUIRED (x1) (x1) CMV (x1) (x1) • While two people continue to hold the assembly in place, set a block of Scrap Wood on top of the Rigid Arms and strike it 5-6 times with a hammer or mallet. You must have wood on top of the Arms before hitting them with a hammer to prevent scratching the powder coating.
  • Page 40 SECTION 6 (CONTINUED) TOOLS AND HARDWARE REQUIRED (x1) • Raise the Backboard until it would not go futher. Use a pencil to mark where the bottom of the Gas Spring Cover (AKG) meets the Gas Spring (AJR). Squeeze the Gas Spring Cover and apply the Height Adjust Sticker (AKP) to the back of the Gas Spring, lining up the 10' line with the pencil mark.

  • Page 41: Warning Sticker

    Son mécanisme a été conçu uniquement pour soutenir le poids du panneau et de l’anneau. N’accrochez rien au manche, à l’anneau, au panneau ni aux leviers sous peine d’endommager l’équipement et d’annuler la garantie. Lifetime Products, Inc., Clearfield, UT 84016 www.lifetime.com 7/12/2016 # 1176611...

  • Page 42: Registration

    . And you can rest assured that Lifetime ® will not sell or provide your personal data to other third parties, or allow them to use your personal data for their own purposes. We invite you to read our privacy policy at www.lifetime.com REGISTER today!
  • Page 43 2. This warranty is nontransferable and is expressly limited to the repair or replacement of defective product. If the product is defective within the terms of this warranty, Lifetime Products, Inc. will repair or replace defective parts at no cost to the purchaser.
  • Page 44 7:00 am–5:00 pm (M–F) MST and 9:00 am–1:00 pm Saturday MST ® AMÉLIORER L’ACHAT LIFETIME EN AJOUTANT DES ACCESSOIRES OU D’AUTRES PRODUITS ® Pour acheter des accessoires ou des autres produits Lifetime , visiter le : www.lifetime.com (Anglais seulement) Ou composer le 1-800-424-3865 Du lundi au vendredi de 7 h à...

Table of Contents