1. Manuals
  2. Brands
  3. Bull Manuals
  4. Server
  5. ESCALA Power7 5886
  6. Installation manual

Bull ESCALA Power7 5886 Installation Manual

Disk drive enclosure
Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
Installing the 5886 disk drive enclosure
REFERENCE
86 A1 24FF 05

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the ESCALA Power7 5886 and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for Bull ESCALA Power7 5886

Summary of Contents for Bull ESCALA Power7 5886

  • Page 1 Installing the 5886 disk drive enclosure REFERENCE 86 A1 24FF 05...
  • Page 3 - Bull Escala E1-700 (Power 710 / 8231-E2B) - Bull Escala E1-705 (Power 710 / 8231-E1C) - Bull Escala E2-700 / E2-700T (Power 720 / 8202-E4B) - Bull Escala E2-705 / E2-705T (Power 720 / 8202-E4C) - Bull Escala E3-700 (Power 730 / 8231-E2B)
  • Page 4 We acknowledge the right of proprietors of trademarks mentioned in this book. The information in this document is subject to change without notice. Bull will not be liable for errors contained herein, or r incidental or consequential damages in connection with the use of this material.

  • Page 5: Table Of Contents

    Contents Safety notices ....... . . v Installing the 58/86 disk drive enclosure ..... . 1 Installing the 58/86 disk drive enclosure: Details .
  • Page 6 Power Systems: Installing the 58/86 disk drive enclosure...

  • Page 7: Safety Notices

    Safety notices Safety notices may be printed throughout this guide. v DANGER notices call attention to a situation that is potentially lethal or extremely hazardous to people. v CAUTION notices call attention to a situation that is potentially hazardous to people because of some existing condition.
  • Page 8 DANGER When working on or around the system, observe the following precautions: Electrical voltage and current from power, telephone, and communication cables are hazardous. To avoid a shock hazard: v Connect power to this unit only with the provided power cord. Do not use the provided power cord for any other product.
  • Page 9 Observe the following precautions when working on or around your IT rack system: v Heavy equipment–personal injury or equipment damage might result if mishandled. v Always lower the leveling pads on the rack cabinet. v Always install stabilizer brackets on the rack cabinet. v To avoid hazardous conditions due to uneven mechanical loading, always install the heaviest devices in the bottom of the rack cabinet.
  • Page 10 CAUTION: Removing components from the upper positions in the rack cabinet improves rack stability during relocation. Follow these general guidelines whenever you relocate a populated rack cabinet within a room or building: v Reduce the weight of the rack cabinet by removing equipment starting at the top of the rack cabinet.
  • Page 11 (L003) All lasers are certified in the U.S. to conform to the requirements of DHHS 21 CFR Subchapter J for class 1 laser products. Outside the U.S., they are certified to be in compliance with IEC 60825 as a class 1 laser product.
  • Page 12 CAUTION: Data processing environments can contain equipment transmitting on system links with laser modules that operate at greater than Class 1 power levels. For this reason, never look into the end of an optical fiber cable or open receptacle. (C027) CAUTION: This product contains a Class 1M laser.

  • Page 13: Installing The 58/86 Disk Drive Enclosure

    Installing the 58/86 disk drive enclosure Use this overview as a guide to the tasks required for installing the 58/86 disk drive enclosure (EXP12S Expansion Drawer) into a rack and cabling it to a server. Procedure You can use the following table to read about and complete the high-level tasks for installing the 58/86 disk drive enclosure.
  • Page 14 Table 1. Tasks to install the disk drive enclosure into a rack (continued) Task Where to find associated information Install the disk drive enclosure on the rail assembly. To install the disk drive enclosure on the rail assembly, see step 4 on page 6. Review information about connecting the disk drive To learn about cabling the disk drive enclosure, see step enclosure, and cable it to the server.

  • Page 15: Installing The 58/86 Disk Drive Enclosure: Details

    Installing the 58/86 disk drive enclosure: Details The detailed installation procedure includes information from online references that are specified in the overview. You can use the expanded instructions in this procedure to install your disk drive enclosure into a rack and to cable it to a server. Before you begin v This information is provided in printed form as a list of basic tasks for installing the 58/86 disk drive enclosure.
  • Page 16 Figure 1. Removing the filler panels c. If necessary, remove the front and back rack doors. d. Mark the rack location where you will install the disk drive enclosure. Choose one of the following options: 1) If you have a rack-mounting template, use it to mark the location. 2) If you do not have a rack-mounting template, perform the following steps: a) Face the front of the rack and work from the left side.
  • Page 17 Figure 2. Marking the installation locations b) Repeat the last step to place two marks on the corresponding mounting holes on the front-right side of the rack. c) Go to the back of the rack. On the left side, find the EIA unit that corresponds to the lowest EIA unit marked on the front of the rack.
  • Page 18 Figure 4. Setting the spacers in place c. Secure the rail to the front of the rack cabinet with one M5 screw in the top hole of the bracket. For racks with square holes, add one washer between the M5 screw and the rail bracket. Figure 5.
  • Page 19 Figure 6. Installing the enclosure on the rails c. Secure the front of the disk drive enclosure to the rack cabinet with one M5 screw in the open hole in each bracket (no washer is required). Figure 7. Installing the securing screws d.
  • Page 20 Figure 8. Routing the power cords through the cord retention brackets f. Install the left bezel, which contains the service indicators, and the right bezel. Fit the cutout on the top of the bezel over the tab on the chassis flange. Rotate the bezel down until it snaps into place. Make sure that the inside surface of the bezel is flush with the chassis.
  • Page 21 6. Cable the disk drive enclosure to the server as follows: a. Confirm that all adapters that you need to connect to the 58/86 disk drive enclosure have been installed in the system. If the adapters have not been installed, complete the adapter installation procedure for your system before continuing with this task.
  • Page 22 If your SAS configuration requirements are not supported by any of these options, go to step 6i on page 13. e. Perform the connection of one 58/86 disk drive enclosure (A) to a single SAS adapter (C) by using a YO cable (B) as shown in Figure 10. Figure 10.
  • Page 23 Figure 11. Connection of two 58/86 disk drive enclosures to a single SAS adapter by using YO cables, where each enclosure can be attached to an additional 58/86 disk drive enclosure by using two EE cables Go to step 6i on page 13. g.
  • Page 24 Figure 12. Connection of two 58/86 disk drive enclosures to a SAS adapter pair by using X cables, where each enclosure can be attached to an additional 58/86 disk drive enclosure by using two EE cables Go to step 6i on page 13. h.
  • Page 25 Figure 13. Connection of one 58/86 disk drive enclosure by using a YI cable to a system with support for a single SAS drawer Go to step 6i. i. For additional information to plan or complete your SAS cable installation, see Serial-attached SCSI cable planning (http://publib.boulder.ibm.com/infocenter/systems/scope/hw/topic/p7had/ p7hadsascabling.htm).
  • Page 26 Power Systems: Installing the 58/86 disk drive enclosure...

  • Page 27: Reference Information

    Reference information Use information in this section as needed to complete enclosure installation and configuration tasks. Connector locations Learn about 12X and system power control network (SPCN) connector locations. Server connectors Learn about connector locations for servers. Model 02E/4B connector locations Learn about connector locations on rack-mounted and stand-alone models.

  • Page 28: Model 02E/4C Connector Locations

    Figure 15. Model 02E/4B connector locations on a stand-alone model Model 02E/4C connector locations Learn about connector locations on rack-mounted models. Notes: The 02E/4C server supports 12X DDR and PCIe cable connector locations as follows: v The card installed in the C1 slot can contain either two 12X DDR cable ports for I/O expansion unit support or one PCIe cable port for PCIe storage enclosure support.

  • Page 29: Model 05F/6B Connector Locations

    Figure 16. Model 02E/4C connector locations on a rack-mounted model Model 05F/6B connector locations Learn about connector locations on rack-mounted and stand-alone models. Figure 17. Model 05F/6B connector locations on a rack-mounted model Reference information...

  • Page 30: Model 05E/6C Connector Locations

    Figure 18. Model 05F/6B connector locations on a stand-alone model Model 05E/6C connector locations Learn about connector locations on rack-mounted models. Notes: The 05E/6C server supports 12X DDR and PCIe cable connector locations as follows: v The card installed in the C1 slot can contain either two 12X DDR cable ports for I/O expansion unit support or one PCIe cable port for PCIe storage enclosure support.

  • Page 31: Model 31E/1C Or 31E/2C Connector Locations

    Figure 19. Model 05E/6C connector locations on a rack-mounted model Model 31E/1C or 31E/2C connector locations Learn about connector locations. Notes: The 31E/1C and 31E/2C servers support 12X DDR and PCIe cable connector locations as follows: v The card installed in the C1 slot can contain either two 12X DDR cable ports for I/O expansion unit support or one PCIe cable port for PCIe storage enclosure support.

  • Page 32: Model 31E/2B Connector Locations

    Figure 21. Model 31E/1C or 31E/2C showing all PCIe connector locations Model 31E/2B connector locations Learn about connector locations on rack-mounted models. Figure 22. Model 31E/2B connector locations on a rack-mounted model Model 33E/8B connector locations Learn about connector locations on rack-mounted models. Figure 23.

  • Page 33: Model 17M/Mb Or 79M/Hb Connector Locations

    Model 17M/MB or 79M/HB connector locations Learn about connector locations. Figure 24. Model 17M/MB or 79M/HB connector locations Model 17M/MC or 79M/HC connector locations Learn about connector locations. Figure 25. Model 17M/MC or 79M/HC connector locations Enclosure connectors Learn about connector locations for I/O enclosures. Reference information...

  • Page 34: Model 58/86 Connector Locations

    Model 58/86 connector locations Learn about connector locations. Figure 26. Model 58/86 connector locations Power Systems: Installing the 58/86 disk drive enclosure...

  • Page 35: Notices

    Notices This information was developed for products and services offered in the U.S.A. The manufacturer may not offer the products, services, or features discussed in this document in other countries. Consult the manufacturer's representative for information on the products and services currently available in your area.

  • Page 36: Trademarks

    This information is for planning purposes only. The information herein is subject to change before the products described become available. This information contains examples of data and reports used in daily business operations. To illustrate them as completely as possible, the examples include the names of individuals, companies, brands, and products.
  • Page 37 the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference, in which case the user will be required to correct the interference at his own expense. Properly shielded and grounded cables and connectors must be used in order to meet FCC emission limits.
  • Page 38 This is a Class A product based on the standard of the VCCI Council. If this equipment is used in a domestic environment, radio interference may occur, in which case, the user may be required to take corrective actions. Japanese Electronics and Information Technology Industries Association (JEITA) Confirmed Harmonics Guideline (products less than or equal to 20 A per phase) Japanese Electronics and Information Technology Industries Association (JEITA) Confirmed Harmonics Guideline with Modifications (products greater than 20 A per...
  • Page 39 Electromagnetic Interference (EMI) Statement - Korea Germany Compliance Statement Deutschsprachiger EU Hinweis: Hinweis für Geräte der Klasse A EU-Richtlinie zur Elektromagnetischen Verträglichkeit Dieses Produkt entspricht den Schutzanforderungen der EU-Richtlinie 2004/108/EG zur Angleichung der Rechtsvorschriften über die elektromagnetische Verträglichkeit in den EU-Mitgliedsstaaten und hält die Grenzwerte der EN 55022 Klasse A ein.

  • Page 40: Class B Notices

    Generelle Informationen: Das Gerät erfüllt die Schutzanforderungen nach EN 55024 und EN 55022 Klasse A. Electromagnetic Interference (EMI) Statement - Russia Class B Notices The following Class B statements apply to features designated as electromagnetic compatibility (EMC) Class B in the feature installation information. Federal Communications Commission (FCC) statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.
  • Page 41 European Community Compliance Statement This product is in conformity with the protection requirements of EU Council Directive 2004/108/EC on the approximation of the laws of the Member States relating to electromagnetic compatibility. IBM cannot accept responsibility for any failure to satisfy the protection requirements resulting from a non-recommended modification of the product, including the fitting of non-IBM option cards.

  • Page 42: Terms And Conditions

    Germany Compliance Statement Deutschsprachiger EU Hinweis: Hinweis für Geräte der Klasse B EU-Richtlinie zur Elektromagnetischen Verträglichkeit Dieses Produkt entspricht den Schutzanforderungen der EU-Richtlinie 2004/108/EG zur Angleichung der Rechtsvorschriften über die elektromagnetische Verträglichkeit in den EU-Mitgliedsstaaten und hält die Grenzwerte der EN 55022 Klasse B ein. Um dieses sicherzustellen, sind die Geräte wie in den Handbüchern beschrieben zu installieren und zu betreiben.
  • Page 43 these publications, or reproduce, distribute or display these publications or any portion thereof outside your enterprise, without the express consent of the manufacturer. Rights: Except as expressly granted in this permission, no other permissions, licenses or rights are granted, either express or implied, to the Publications or any information, data, software or other intellectual property contained therein.
  • Page 44 Power Systems: Installing the 58/86 disk drive enclosure...

Table of Contents