Table of Contents
Related Manuals for Samsung MWR-WE13
Summary of Contents for Samsung MWR-WE13
- Page 1 Air conditioner Installation manual Wired remote controller MWR-WE13 • Thank you for purchasing this Samsung Product. • Before operating this unit, please read this installation manual carefully and retain it for future reference. DB68-07634A-00...
-
Page 2: Table Of Contents
Contents Safety Information Safety Information Installation Wired Remote Controller Installation Optional accessories External Dimensions Wired Remote Controller Installation Tracking Your Indoor Unit from the Wired Remote Controller Individual Control with Your Wired Remote Controller Group Control with Your Wired Remote Controller Controlling 2-Remote controller Initializing Your Wired Remote Controller Communication Errors Displayed on Your Wired Remote Controller... -
Page 3: Safety Information
Safety Information This installation manual explains how to install a Wired Remote Controller connected to the indoor unit of your Samsung system air conditioner. Please read this manual thoroughly before installing the product. (Please refer to appropriate installation for any optional product installation.) WARNING Hazards or unsafe practices that may result in severe personal injury or death. -
Page 4: Installation
Wired Remote Controller Installation Optional accessories Wired Remote Installation Item Cable Tie Cable Clamp M4X16 Screw User Manual U Terminal Controller Manual Quantity Shape CAUTION • The Wired Remote Controller should be installed by an installation expert. • Check and confirm the power is off before installing your Wired Remote Controller. •... - Page 5 Wired Remote Controller Installation Push the two hooks at the bottom of your Wired Remote Controller at the same time, and then pull up the front cover to separate it from the rear cover. NOTE • Insert a flat head screwdriver into the square groove in the upper area of the hook to disassemble it easily.
-
Page 6: Wired Remote Controller Installation
Wired Remote Controller Installation Using more than two screws, firmly affix the rear cover of the remote controller to the wall, and then connect the power(V1, V2) and communication cables(F3, F4), making sure these cables have reasonable length, to the terminal at the back of the cover. 10 mm(0.4 inch) 10 mm (0.4 inch) or more... -
Page 7: Tracking Your Indoor Unit From The Wired Remote Controller
• The following are the specs of the compression ring terminal connected to your Wired Remote Controller PCB. Stud ØD Rated Size Stud Size Basic Size [mm (inch)] mm² mm² ØD (inch²) (inch²) (inch) 0.25~1.65 10.0 21.2 22~16 1.5 (0.0023) 3 (0.1181) (0.0003 ~ 0.0025) (0.0275) -
Page 8: Individual Control With Your Wired Remote Controller
Wired Remote Controller Installation Individual Control with Your Wired Remote Controller Individual control means that you are using one remote controller to control one indoor unit or ventilator(ERV). When Connected to an Indoor Unit Only Outdoor Unit COM1 (F1, F2) COM1 (F1, F2) Indoor Unit Indoor Unit... -
Page 9: Group Control With Your Wired Remote Controller
Group Control with Your Wired Remote Controller Group control means that you are using one Wired Remote Controller to control two or more indoor units and ventilator(ERV) at the same time. When Connected to an Indoor Unit Only • Using One Wired Remote Controller to control three indoor Units Outdoor Unit COM1 (F1, F2) COM1 (F1, F2) - Page 10 Wired Remote Controller Installation When Connected to an ventilator(ERV) Only • Using One Wired Remote Controller to Control Three ventilator(ERV) Master ventilator(ERV) COM1 (F1, F2) COM1 (F1, F2) COM1 (F1, F2) Ventilator(ERV) Ventilator(ERV) Ventilator(ERV) COM2 (F3, F4) COM2 (F3, F4) Wired Remote Controller NOTE •...
- Page 11 When Connected to an Indoor Unit and an ventilator(ERV) together • Using One Wired Remote Controller to control multiple indoor units and ventilator(ERV) Outdoor Unit COM1 (F1, F2) COM1 (F1, F2) COM1 (F1, F2) Ventilator (ERV) Indoor Unit Indoor Unit Indoor Unit COM2 (F3, F4) COM2 (F3, F4)
-
Page 12: Controlling 2-Remote Controller
Wired Remote Controller Installation Controlling 2-Remote controller 2-Remote controller is controlling one indoor unit, ventilator(ERV) or one group of indoor units and ventilator(ERV) with two remote controllers. When Connected to an Indoor Unit Only Outdoor Unit COM1 (F1, F2) Indoor Unit COM2 (F3, F4) Wired Remote Wired Remote... - Page 13 When Connected to an Indoor Unit and an ventilator(ERV) Together Outdoor Unit COM1 (F1, F2) Indoor Unit COM2 (F3, F4) Ventilator (ERV) COM2 (F3, F4) Wired Remote Wired Remote Controller (Master) Controller (Slave) NOTE • Regardless of the indoor unit group address (RMC address), only the indoor units connected to COM2 are controlled by 2-remote controller.
-
Page 14: Initializing Your Wired Remote Controller Communication
Wired Remote Controller Installation Initializing Your Wired Remote Controller Communication Wired remote controller must be initialized if installation status changes. • Changing number of ventilator (ERV)/indoor unit or their address Press the Delete and ESC buttons at the same time for more than five seconds. •... -
Page 15: Errors Displayed On Your Wired Remote Controller
Errors Displayed on Your Wired Remote Controller Error codes for the Wired Remote Controller and the product connected to your Wired Remote Controller will be displayed in the LCD display. LCD Display When an Error Occurs in Your Indoor/Outdoor Units (Product Group Display: A) The product address for the error will be displayed, followed by the error code. - Page 16 Wired Remote Controller Installation Wired Remote Controller Error Codes Display Description Communication error between wired remote controller and indoor/ERV units after successful communication. No communication between Master(Main) and Slave(Sub) wired remote controllers. No communication between wired remote controller and indoor/ERV units Wired remote controller is connected on F1/F2 channel.
-
Page 17: Service Mode
Wired Remote Controller Installation/Service Mode Additional Functions of Your Wired Remote Controller Data bit Main Menu Sub-menu 1 2 3 4 If you want to use the various additional functions for your Wired Remote Controller, press the Delete and Set buttons at the same time for more than three seconds. -
Page 18: Installation/Service Mode
Wired Remote Controller Installation/Service Mode Installation/Service Mode NOTE • ‘NONE’ will be displayed if the indoor unit does not support the function. In some cases, the setting may not possible or it may be not applied though it is set on the unit. •... - Page 19 Main Data Factory Function Description Unit menu menu setting Software code Software code Software version Software version Indoor unit room temperature 1,2,3 Room temperature °C Indoor unit EVA IN temperature 1,2,3 EVA IN temperature °C Indoor unit EVA OUT temperature 1,2,3 EVA OUT temperature °C...
- Page 20 Wired Remote Controller Installation/Service Mode Main Data Factory Function Description Unit menu menu setting Use of cold air prevention 0-No use, 1-Use Use of humidification when 0-No use, 1-Use heating thermo off ERV Plus setting/checking Use of fan operation in 0-No use, 1-Use Defrost operation Use of humidification when...
- Page 21 1)* The total option codes are 24 digits. You can set six digits at a time and it is distinguished by page number. Press [ ] button to go to the next page. Page number Option Code Option Code SEG1 SEG2 SEG3 SEG4...
-
Page 22: The Example Of Wired Remote Controller Option Setting Method
Wired Remote Controller Installation/Service Mode The example of Wired Remote Controller option setting method Press Delete and Set buttons at the same time for more than 3 seconds. • (Main menu) will be displayed and then press the [ ]/[ ] button to select no.1. - Page 23 MEMO English 23...