Related Manuals for DHP 10125-M
Summary of Contents for DHP 10125-M
- Page 1 DOREL HOME PRODUCTS DOREL HOME PRODUCTS DOREL HOME PRODUCTS DOREL HOME PRODUCTS IM STATUS: APPROVED December-23-11 Issued by: fouad.koudsi@dhpfurniture.com...
- Page 2 · Recommended # of people needed for assembly 2 (however it is always better to have an extra hand.) Estimated assembly time is 2 hour. · THIS INSTRUCTION BOOKLET CONTAINS IMPORTANT SAFETY INFORMATION. PLEASE READ AND KEEP FOR FUTURE REFERENCE B34541709603-10125-M...
- Page 4 PARTS LEG POST 1 T912080 QTY: 1 LEG POST 3 LEG POST 2 T912100 REAR GUARD RAIL T912090 FRONT GUARD RAIL QTY: 1 T912110 QTY: 2 T912120 QTY: 1 QTY: 1 1 HOLE 1 AGUJERO 4 HOLES 4 AGUJEROS UPPER SIDE RAIL T912130 LADDER SIDE RAIL QTY: 1...
- Page 5 PARTS POST LINKS SLATS T912190 T912170 QTY: 4 QTY: 44 LADDER T912180 QTY: 1 SLATS SPACERS T391650 POST RAILS QTY: 42 T912200 QTY: 2 PLASTIC PLUG T391660 QTY: 88 NOTE: PART HAS PROTECTIVE END CAPS PRE-INSTALLED 4 /15 B34541709603...
- Page 6 PARTS HEX KEY T290110 SCREW QTY: 1 BOLT ST 4.2 x 10 mm BOLT 1/4"-20 x 5/8" T114640 5/16" x 3/4" T127270 QTY: 16 T128190 QTY: 22 QTY: 16 BOLT 1/4"-20 x 2 3/8" T126600 QTY: 3 BOLT HARDWARE NOTE: 1/4"-20 x 1 5/8"...
- Page 7 ALWAYS USE THE RECOMMENDED SIZE MATTRESS OR MATTRESS SUPPORT, OR BOTH, TO HELP PREVENT THE LIKELIHOOD OF ENTRAPMENT OR FALLS. TO PREVENT INJURY, DHP RECOMMENDS ONE TWIN SIZE MATTRESS AND ONE FULL SIZE MATTRESS TO BE USED. USE ONLY A TWIN MATTRESS WHICH IS 74"-75" LONG AND 37 1/2"-38 1/2" WIDE ON UPPER BUNK AND A TWIN MATTRESS WHICH IS 74"-75" LONG AND 37 1/2"-38 1/2" WIDE ON LOWER BUNK.
- Page 8 Attach the POST LINKS (M) to the POST RAILS (O) with the SCREWS (4). Attach the POST RAILS (O) to the LEG POSTS (A and B) with the SCREWS (4) as shown. Attach the END GUARD RAILS (I) to the LEG POSTS (A and B) with the BOLTS (2) as shown.
- Page 9 Attach the SIDE RAILS (G, H & J) to the LEG POSTS (A, B & C) with the BOLTS (3) as shown below. Hardware Required 8 /15 B34541709603...
- Page 10 Attach the GUARD RAILS (E & F) to the LEG POSTS (A & B) with the BOLTS (2) as shown in detail (1). Attach the GUARD RAILS (E & F) to the SIDE RAILS (G & H) with the BOLTS (1) as shown in detail (2). DETAIL (1) Hardware Required DETAIL (2)
- Page 11 Carefully attach the SLATS (K) to the UPPER SIDE RAILS (G & H). Lock the SLATS (K) into place with 44 PLASTIC PLUGS (R), as shown in detail (1). Repeat this procedure for the lower bed as shown in detail (2). DETAIL 1 DETAIL 2 10 /15...
- Page 12 For the upper bed, attach 19 SLAT SPACERS (R) between SLATS (K) as shown in DETAIL (1). Repeat the same procedure for the lower bed. Attach the LADDER (L) to the LADDER SIDE RAIL (H) with the BOLTS (6) as shown in DETAIL (2). DETAIL 1 DETAIL 2 Hardware Required...
- Page 13 5417096 Limites Del Peso: 225 lbs\ 102 kgs NO REGRESE ESTE PRODUCTO A LA TIENDA ALTO ALTO Las tiendas no tienen partes. Si faltan partes o las partes están dañadas llame gratis al servicio al cliente. Con gusto mandamos las partes. Sin cargo alguno. Necesitas partes o Asistencia? o visitar la página de internet www.dhpfurniture.com Para servicio más rápido y confiable por favor tenga este manual listo.
- Page 14 PROBABILIDAD DE QUEDAR ATRAPADO O DE CAÍDAS. * PARA PREVENIR LESIÓN, DHP RECOMIENDA QUE SE UTILICE UN COLCHÓN DE TAMAÑO INDIVIDUAL Y UN COLCHÓN DE TAMAÑO MATRIMONIAL. * UTILICE SOLAMENTE UN COLCHÓN INDIVIDUAL QUE SEA 74"-75"DE LARGO Y 37 ½"-38 1/2" DE ANCHO EN LA CAMA SUPERIOR Y UN COLCHÓN INDIVIDUALQUE SEA 74"-75"...
- Page 15 PÁGINA 07 Una los ACOPLAMIENTOS del POSTE (M) a los CARRILES del POSTE (O) con los TORNILLOS (4). Ate los CARRILES del POSTE (O) a los POSTES de la PIERNA (A Y B) con los TORNILLOS (4) como se muestra. Una los CARRILES de PROTECTOR del EXTREMO (I) a los POSTES de la PIERNA (A Y B) con los PERNOS (2) como se muestra.