Related Manuals for Viper 460XV
Summary of Contents for Viper 460XV
- Page 1 4 4 6 6 0 0 X X V V M M o o d d e e l l ➤ O O w w n n e e r r ’ ’ s s G G u u i i d d e e...
- Page 2 l l i i m m i i t t e e d d l l i i f f e e t t i i m m e e c c o o n n s s u u m m e e r r w w a a r r r r a a n n t t y y Directed Electronics, Inc.
- Page 3 CONSEQUENTIAL DAMAGES OF ANY KIND. IN THE EVENT OF A CLAIM OR A DISPUTE INVOLVING DIRECTED OR ITS SUBSIDIARY, THE PROPER VENUE SHALL BE SAN DIEGO COUNTY IN THE STATE OF CALIFORNIA. CALIFORNIA STATE LAWS AND APPLICABLE FEDERAL LAWS SHALL APPLY AND GOVERN THE DISPUTE.
-
Page 4: Table Of Contents
t t a a b b l l e e o o f f c c o o n n t t e e n n t t s s l l i i m m i i t t e e d d l l i i f f e e t t i i m m e e c c o o n n s s u u m m e e r r w w a a r r r r a a n n t t y y ................3 3 s s t t a a n n d d a a r r d d t t r r a a n n s s m m i i t t t t e e r r c c o o n n f f i i g g u u r r a a t t i i o o n n . - Page 5 © 2005 directed electronics, inc.
- Page 6 s s t t a a n n d d a a r r d d t t r r a a n n s s m m i i t t t t e e r r c c o o n n f f i i g g u u r r a a t t i i o o n n controls the L L o o c c k k –...
- Page 7 : : Your system MUST be installed by an Authorised dealer in accor- dance with the instructions we supply them. The Viper 460XV system is designed to be installed in any petrol or common rail diesel vehicle with a 12-volt battery.
-
Page 8: System Maintenance
n n o o t t e e : : The Installation Certificate must be completed by your installer at the authorised dealer. Other than the remote controls, this system has no user-serviceable parts. Your authorised dealer can correct any system wiring problems and, if needed, can return any malfunctioning compo- nent to Directed Electronics for repair/replacement under the terms of the Limited Lifetime Warranty printed at the beginning of this guide. -
Page 9: Standard Configuration
➜ standard configuration Button The arming function is controlled by pressing this button for one second. Button The disarming function is controlled by pressing this button for one second. Button Silent Mode™ and an optional auxiliary function are controlled by pressing this button. (Silent Mode works by pressing this button for less than one second before arming or disarming. -
Page 10: Active Arming
Buttons An optional auxiliary convenience or expansion function that you have added to your system can be activated by pressing these buttons simultaneously. This output controls_________________________. Buttons An optional auxiliary convenience or expansion function that you have added to your system can be activated by pressing these buttons simultaneously. -
Page 11: Passive Arming
While the system is armed, the status LED will flash approxi- mately once per second, indicating that the system is actively protecting your vehicle. If you hear a second chirp after arming, and see the status LED flashing in groups, refer to the Diagnostics section of this guide. -
Page 12: One-Time Bypass
When armed, your vehicle is protected as follows: ➤ Movement inside the passenger compartment will trigger the system. The triggered sequence is 30 seconds of constant siren and indicator light flashing. ➤ If a door is opened, the system will immediately trigger. ➤... -
Page 13: Transmitter Sensor Disable
To activate one-time bypass: 1. After parking turn the ignition off. 2. Turn the ignition On for more than 1-second and less than 3-seconds. 3. The siren will chirp once to indicate one-time bypass has been activated. To cancel one-time bypass perform one of the following: Arm then disarm the alarm. -
Page 14: High Security Disarm
➜ disarming To disarm the system, press the indicators will flash twice. If the vehicle's central locking is connected to the system, the doors will unlock. If the siren chirps either four or five times when disarming, refer to the Diagnostics section of this guide. -
Page 15: Disarming Without A Transmitter
➜ disarming without a transmitter This feature allows you to disarm the system without the trans- mitter should it be lost, damaged, or disabled. In order to disarm without a transmitter, you must have the vehicle’s ignition key, know where the Valet switch is located, and have the PIN code. Check with the installer for the location of the Valet switch. -
Page 16: Interior Light Control
5. Enter the second number in your PIN (press the Valet switch three times). 6. Turn the ignition key OFF. 7. Turn the ignition key to the ON position 8. Enter the third number in your PIN (press the Valet switch four times). -
Page 17: Silent Mode
full The interior light activates for 30-seconds after seeing door closure, ignition, or security disarm. (This is the factory setting.) ➜ silent mode To arm or disarm the system without siren chirps, use Silent Mode™. Simply press arming or disarming, and the confirmation chirp(s) will be elim- inated for that one operation only. - Page 18 To enter Valet Mode: 1. Turn the ignition on. 2. Turn the ignition off. 3. Press and release the Valet button within 10 seconds. The status LED will light solidly to indicate the system has entered Valet Mode. To exit Valet Mode: 1.
-
Page 19: Arming Diagnostics
d d i i a a g g n n o o s s t t i i c c s s The microprocessor at the heart of your security system is constantly monitoring all of the switches and sensors that are connected to it. -
Page 20: Disarming Diagnostics
➜ disarming diagnostics Extra disarm chirps are the Tamper Alert. If four chirps are heard when disarming, the system was triggered in your absence. If five chirps are heard, a zone was triggered so many times that Nuisance Prevention Circuitry has bypassed that zone. The status LED will ®... -
Page 21: Table Of Zones
➜ table of zones The zone number is the number of LED flashes used by the system to identify that input. The standard input assignments are listed below, along with spaces to write in any optional sensors or switches you have had installed. Zone - Number of LED Flashes ➜... - Page 22 Example If Zone 3 was active or triggered, the LED will flash three times with a two-second pause. Then it will flash three times again, and repeat until the ignition is turned on. note: Your system stores the last six triggered zones in memory.
- Page 23 h h i i g g h h f f r r e e q q u u e e n n c c y y Your system transmits and receives at 433 MHz. This provides a cleaner spectrum with less interference and a more stable signal. o o w w n n e e r r r r e e c c o o g g n n i i t t i i o o n n Owner Recognition is a feature available exclusively from Directed.
- Page 24 r r a a p p i i d d r r e e s s u u m m e e l l o o g g i i c c This Directed system will store its current state to non-volatile memory.
- Page 25 p p r r o o g g r r a a m m m m i i n n g g Programming options control what your system does during normal operation, and require few or no additional parts. However, some may require additional installation labour. The following is a list of the program settings, with the factory settings in B B o o l l d d : : ➤...
- Page 26 been left open. This feature is useful if a door has been left ajar when leaving the vehicle. Forced passive arming ensures that the security system will be armed in every situation. ➤ Vehicle Recovery System (VRS): Refer to section later in this guide.
-
Page 27: E E H H I I C C L L E E R R E E C C O O V V E E R R Y Y S S Y Y S S T T E E M M ( ( V V R R S
v v e e h h i i c c l l e e r r e e c c o o v v e e r r y y s s y y s s t t e e m m ( ( v v r r s s The optional VRS authorised user of your vehicle (even if using your keys and remote control) will not be able to permanently separate you from your... -
Page 28: Arming The Vrs
➜ arming the vrs ® To arm the VRS , turn the ignition to the ON position and press ® the arm button on the remote transmitter for one second. The indicator lights will flash and the siren will chirp once. This can be done before driving or while driving the vehicle. -
Page 29: Disarming The Vrs
after the constant siren output begins, the flashing Three minutes indicator lights and the siren will stop. The immobiliser will remain active until the system is disarmed. If the door is opened or the ignition is turned off and on in an attempt to restart the car, the siren and light flashing will begin again. - Page 30 1. Turn the ignition on. 2. Begin entering your 4-digit PIN code as noted in the Entering Your PIN section of this guide. p p r r o o g g r r a a m m m m i i n n g g o o p p t t i i o o n n s s See your dealer for further details on the options listed below available with this system.
- Page 31 Retained Accessory Power can be connected to vehicle accessories, such as the vehicle radio. After the ignition has been turned off, it will continue to supply power until a door has been open and closed. u u l l t t r r a a s s o o n n i i c c s s e e n n s s o o r r s s Your security system incorporates two Ultrasonic sensors, which are most commonly mounted at the top of the A-pillars facing the rear of the vehicle.
- Page 32 s s e e c c u u r r i i t t y y & & c c o o n n v v e e n n i i e e n n c c e e e e x x p p a a n n s s i i o o n n s s Here we have listed only some of the many expansion options available.
- Page 33 Automatic electric window control is Electric Window Control: provided with the 529T and 530T systems. For the ultimate in convenience, the Valet Valet Start System: 561T* start system can start your vehicle, monitor engine func- tions, and power your climate control system with a push of a button.
- Page 34 : Noise generating device usually installed in the engine Siren compartment of the vehicle. It is responsible for generating the "chirps" you hear, as well as the tones you hear while the alarm is triggered. : Hand-held, remote control which operates the Transmitter various functions of your system.
- Page 35 © 2005 directed electronics, inc.
-
Page 36: Health Check
health check Directed Electronics recommends you return to your installing Viper dealer to have your system checked for correct operation. The first check is due one year after the installation date and at yearly intervals thereafter. n n o o t t e e : : There may be a small charge incurred for this service. ©... - Page 37 Your factory set 4-digit PIN code is noted below. See this manual for information on using your PIN code. place sticker here The company behind this system is Directed Electronics, Inc. E&OE, specification is subject to change without notice. Some vehicles require optional parts/wiring and a few are incompatible with some features.