Arcan BLACKLINE XL35B Manual

3.5 ton professional low lift service jack

Advertisement

WARNING INFORMATION
This is the safety alert symbol. It is used to alert you
to potential personal injury hazards. Obey all safety
messages that follow this symbol to avoid possible
injury or death.
IMPORTANT: READ THESE INSTRUCTIONS BEFORE OPERATING
BEFORE USING THIS DEVICE, READ THIS MANUAL COMPLETELY AND THOROUGHLY, UNDERSTAND ITS OPERATING
PROCEDURES, SAFETY WARNINGS AND MAINTENANCE REQUIREMENTS.
It is the responsibility of the owner to make sure all personnel read this manual prior to using the device. It is also the responsiblity of
the device owner to keep this manual intact and in a convenient location for all to see and read. Contact Arcan Customer Service for a
replacement label if your jack's label is not readable. If the operator is not fluent in English, the product and safety instructions shall be
read to and discussed with the operator in the operator's native language by the purchaser/owner or his designee, making sure that the
operator comprehends its contents.
THE NATURE OF HAZARDOUS SITUATIONS
WARNING
The use of Portable Automotive Lifting Devices are subject to certain hazards that cannot be prevented by mechanical means, but only
by the exercise of intelligence, care, and common sense. It is essential to have personnel involved in the use and operation of the device
who are careful, competent, trained, and qualified in the safe operation of the device and its proper use when servicing motor vehicles
and their components. Examples of hazards are dropping, tipping or slipping of loads caused primarily by improperly securing loads,
overloading, off-centered loads, use on other than hard level surfaces, and using equipment for a purpose for which it was not intended.
METHODS TO AVOID HAZARDOUS SITUATIONS
WARNING
Read, study, understand and follow all instructions before operating this device.
Inspect the jack before each use. Do not use jack if damaged, altered, modified, in poor condition, leaking hydraulic fluid, or
unstable due to loose or missing components. Make corrections before using.
Lift only on areas of the vehicle as specified by the vehicle manufacturer.
User and bystander must wear eye protection that meets ANSI Z87.1 and OSHA standards.
Do not use jack beyond its rated capacity. Do not shock load.
THIS IS A LIFTING DEVICE. Immediately after lifting, support the vehicle with jack stands capable of sustaining the load before
working on the vehicle.
Use only on a hard level surface free from obstructions so the jack is free to reposition itself during lifting and lowering
operations.
Center load on saddle. Be sure setup is stable before working on vehicle.
Do not move or dolly the vehicle while on the jack.
Do not use any materials that may serve as risers, spacers or extenders between the stock lifting saddle and the load.
Do not use any adaptors that replace the stock lifting saddle unless approved or supplied by the jack manufacturer.
Do not use (or modify) this product for any other purpose than that for which it was designed without consulting the
manufacturer's authorized representative.
Always lower the jack slowly and carefully.
Failure to heed these warnings may result in fatal personal injury and/or property damage.
WARNING: This product can expose you to chemicals including nickel, which is known to the State of California to cause
cancer and birth defects or other reproductive harm. For more information go to www.P65Warnings.ca.gov
CONSEQUENCES OF NOT AVOIDING HAZARDOUS SITUATIONS
WARNING
Failure to read this manual completely and thoroughly, failure to understand its OPERATING INSTRUCTIONS, SAFETY WARNINGS,
MAINTENANCE INSTRUCTIONS and comply with them, and failure to comply with the METHODS TO AVOID HAZARDOUS SITUATIONS
could cause accidents resulting in serious or fatal personal injury and/or property damage.
3.5 Ton Professional Low Lift Service Jack
For Technical Questions, Call: 1-800-879-7316
WARNING
1
Model XL35B
WARNING: Indicates a hazardous situation
which, if not avoided, could result in death
or serious injury.
.
REV: 12/03/19

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the BLACKLINE XL35B and is the answer not in the manual?

Questions and answers

Summary of Contents for Arcan BLACKLINE XL35B

  • Page 1 It is the responsibility of the owner to make sure all personnel read this manual prior to using the device. It is also the responsiblity of the device owner to keep this manual intact and in a convenient location for all to see and read. Contact Arcan Customer Service for a replacement label if your jack's label is not readable.
  • Page 2 INSPECTION Visual inspection should be made before each use of the jack, checking for leaking hydraulic fluid and damaged, loose or missing parts. Any jack which appears to be damaged in any way, is found to be badly worn, or operates abnormally MUST BE REMOVED FROM SERVICE until necessary repairs are made.
  • Page 3: Operation

    OPERATING INSTRUCTIONS This is the safety alert symbol used for the OPERATING INSTRUCTIONS section of this manual to alert you to potential personal injury hazards. Obey all instructions to avoid possible injury or death. IMPORTANT: Before attempting to raise any vehicle, check vehicle service manual for recommended lifting surfaces.
  • Page 4: Regular Maintenance

    HYDRAULIC MAINTENANCE GUIDE IMPORTANT: Service jacks are designed for lifting purposes only; always support raised load with jack stands. REGULAR MAINTENANCE MONTHLY or as necessary (depending on usage) #1 Using a grease gun, add grease to grease fitting in the lift arm pivot shaft. (Use a multi-purpose NLGI type grease only.) #2 Lubricate all linkages and pivot points.
  • Page 5: Parts List And Diagram

    PARTS LIST AND DIAGRAM Item No. Part No. Description Item No. Part No. Description RS35T01 Star Clip RS35T11BK Handle Yoke Assembly RS35T02 Washer M20 RS35T12 Grease Fitting RS35T03BK Front Wheel RS35T13 Handle Set Screw RS35T04 Retaining Ring M16 RS35T14 Yoke Pivot Bolt and Washer RS35T05ABK Saddle...
  • Page 6: Specifications

    TOOLS BRANDED PRODUCTS ARE FREE FROM DEFECTS IN WORKMANSHIP AND MATERIALS. Arcan® Professional Tools will repair or replace its Arcan® Professional Tools branded products which fail to give satisfactory service due to defective workmanship or materials, based upon the terms and conditions of the following described warranty plans attributed to that specific product.

Table of Contents

Save PDF