Subscribe to Our Youtube Channel
Related Manuals for Vintage Air MINI SLIMLINE 10301-VUX-A
Summary of Contents for Vintage Air MINI SLIMLINE 10301-VUX-A
- Page 1 an ISO 9001:2008 Registered Company MINI SLIMLINE HEAT/COOL 10301-VUX-A 10401-VUX-A 900301 REV D 10/28/14, MINI SLIMLINE HC PG 1 OF 12...
- Page 2 MINI SLIMLINE HEAT/COOL Table of Contents PAGES COVER TABLE OF CONTENTS PACKING LIST INFORMATION PAGE INSTALLATION INSTALLATION CONTINUED HOSE ROUTING O-RING/FITTING INSTRUCTIONS HEATER HOSE INSTALLATION WIRING DIAGRAM THERMOSTAT ADJUSTMENT EVAPORATOR KIT PACKING LIST 900301 REV D 10/28/14, MINI SLIMLINE HC PG 2 OF 12...
- Page 3 INSTALLATION KIT ** BEFORE BEGINNING INSTALLATION, OPEN ALL PACKAGES AND CHECK CONTENTS OF SHIPMENT. PLEASE REPORT ANY SHORTAGES DIRECTLY TO VINTAGE AIR WITHIN 15 DAYS. AFTER 15 DAYS, VINTAGE AIR WILL NOT BE RESPONSIBLE FOR MISSING OR DAMAGED ITEMS. ECONO HEAT NOTE: IMAGES MAY NOT DEPICT ACTUAL PARTS AND QUANTITIES.
- Page 4 WITH A HEAT GUN OR BY RUNNING THE ENGINE WITH THE HEATER ON BEFORE EVACUATING. LEAK CHECK AND CHARGE TO SPECIFICATIONS. VINTAGE AIR SYSTEMS ARE DESIGNED TO OPERATE WITH R134a REFRIGERANT ONLY! USE OF ANY OTHER REFRIGERANTS IS A FIRE HAZARD AND COULD DAMAGE EITHER YOUR AIR CONDITIONING SYSTEM OR YOUR VEHICLE.
-
Page 5: Installation
MINI SLIMLINE HEAT/COOL INSTALLATION 1. ATTACH EVAPORATOR BRACKETS TO EVAPORATOR. 2. DRILL (2) 9/32” HOLES UNDER THE DASH LIP WITH EVAPORATOR BRACKETS ATTACHED TO EVAPORATOR AS SHOWN IN FIGURE 1, BELOW. DASH 1/4” x 1/2” BOLTS WITH FLAT WASHERS EVAPORATOR DRILL (2) FIGURE 1 9/32”... - Page 6 HOSES WILL CONFORM TO THE LOCATION FOR THE BULKHEAD FITTINGS OR OPTIONAL BULKHEAD PLATE (VINTAGE AIR PART #34215-VUQ OR 34217-VUQ). THE 1/2” HOSE IS HARD TO BEND AT A SHARP ANGLE, AND THE FITTINGS TAKE UP A CERTAIN AMOUNT OF SPACE. BEFORE YOU DRILL HOLES IN YOUR FIREWALL, MAKE SURE THAT YOU CAN MAKE THE HOSES FIT WHERE YOU HAVE PLANNED.
- Page 7 900301 REV D 10/28/14, MINI SLIMLINE HC PG 7 OF 12...
-
Page 8: O-Ring/Fitting Instructions
BE CAREFUL TO ENSURE THAT THIS WIRE IS NOT PINCHED OR IN A POSITION TO RUB ON A SHARP EDGE AS IT GOES THROUGH THE FIREWALL. AN OPTIONAL VACUUM RESERVOIR WITH CHECK VALVE WILL HELP SYSTEM WORK UNDER A VARIETY OF CONDITIONS (VINTAGE AIR PART #31200-VUS VACUUM RESERVOIR). 900301 REV D 10/28/14, MINI SLIMLINE HC PG 8 OF 12... -
Page 9: Heater Hose Installation
FOLLOW ANTIFREEZE RECOMMENDATIONS WILL CAUSE HEATER CORE TO CORRODE PREMATURELY AND POSSIBLY BURST IN THE A/C MODE AND/OR FREEZING WEATHER, VOIDING YOUR WARRANTY. CHECK COMPLETE A/C ASSEMBLY FOR PROPER OPERATION. VINTAGE AIR RECOMMENDS THAT ALL A/C SYSTEMS BE SERVICED BY A CERTIFIED AUTOMOTIVE AIR CONDITIONING TECHNICIAN ONLY. SEE INSIDE COVER FOR SERVICE INFORMATION. - Page 10 VALVE ALTERNATOR, OR STARTER SOLENOID. BLACK ENGINE VACUUM TO INTAKE MANIFOLD VACUUM SOURCE OPTIONAL VACUUM RESERVOIR VACUUM VINTAGE AIR PART#31200-VUS RESERVOIR WI RES = BLACK VACUUM LI NES = 900301 REV D 10/28/14, MINI SLIMLINE HC PG 10 OF 12...
- Page 11 MINI SLIMLINE HEAT/COOL COLDER CLOCKWISE ADJUSTABLE KNOB CAPILLARY WARMER COUNTERCLOCKWISE TUBE EVAPORATOR COIL AIR CONDITIONING ADJUSTMENTS: THE AIR CONDITIONER THERMOSTAT CONTROLS COIL TEMPERATURE. THERMOSTATS ARE SHIPPED ADJUSTED • FULLY COLD (CLOCKWISE). IN THE MAJORITY OF CASES, THE A/C WILL OPERATE CORRECTLY AS SHIPPED. TURNING THE KNOB TO THE RIGHT (CLOCKWISE) MAKES THE SYSTEM OPERATE COLDER.
- Page 12 MINI SLIMLINE HEAT/COOL EVAPORATOR KIT 10301-VUX-A EVAPORATOR KIT PACKING LIST 10401-VUX-A No. QTY. PART No. DESCRIPTION 55326-VUE-A EVAPORATOR SUB CASE H/C w/ STD LOUVERS 55426-VUE-A EVAPORATOR SUB CASE H/C w/ BLK LOUVERS 64143-VUE EVAPORATOR MOUNTING BRKT. KIT 49141-VUX CONTROL POD W/ WIRING 63300-VUE INSTALLATION KIT CHECKED BY:...
Need help?
Do you have a question about the MINI SLIMLINE 10301-VUX-A and is the answer not in the manual?
Questions and answers