Care & Maintenance; Troubleshooting Guide; Replacement Parts - Ninja BL450 Series Owner's Manual

Care & Maintenance
HOW TO CLEAN
CAUTION: Make sure that the motor base is
unplugged from the power source before inserting
or removing any attachment and before cleaning.
CAUTION: DO NOT immerse the motor base into
water or any other liquid.
CAUTION: Use caution when handling the blade
assemblies as the blades are very sharp.
1
Separate/remove all parts from each other.
2 Clean the motor base with a damp cloth and wipe dry.
3 Place cups in the dishwasher. Place the lids, and
attachments on the top rack.
OR
4 Carefully hand wash the lids, Nutri Ninja cups, and blade
®
assemblies in warm, soapy water with a soft cloth.
If the appliance needs servicing, please call customer
service at 1-877-646-5288.
12 1-877-646-5288
HOW TO STORE
1 Store the Nutri Ninja Pro Blender upright. Secure the
power cord underneath the base by wrapping the cord
around the cord wrap. Do not place anything on top.
Store the cups and the rest of the attachments along
side the appliance where they will not be damaged and
won't cause a hazard.
RESETTING THE MOTOR THERMOSTAT
The Nutri Ninja Pro Blender features a unique safety
system which prevents damage to the unit's motor
and drive system should you inadvertently overload
your appliance. If the appliance is being overloaded,
the motor will stop. To reset the appliance, follow the
resetting procedure below:
1 Unplug the appliance from the electrical outlet.
2 Remove and empty the cup and ensure that no food is
jamming the cutting blades.
3 Allow the appliance to cool for approximately 30 minutes.
4
Re-install the cup onto the base and re-plug the
appliance into the electrical outlet.
5
Proceed to use the appliance as before while making sure
not to exceed the recommended maximum capacities.

Troubleshooting Guide

PROBLEMS
Motor doesn't start or
• For the cups, make sure that the tabs are seated in the slots and
attachment doesn't rotate. turned clockwise.
•
Either you are chopping too much food at once, or you are not pulsing
Food is unevenly chopped.
properly. Reduce the amount of food in the cup.
Food is too finely chopped or
•
The food has been over processed. Use short pulses for best results.
too watery. Press down on the cup in short intervals.
•
For best results use ice straight from the freezer. Try using short pulses
You cannot achieve snow
instead of one long one.
from ice cubes.
•
Make sure the cup is completely dry before adding ice.
• Make sure that your lid or blade assembly is properly assembled to the
Cup is leaking.
cup. Leaking may occur if it is misaligned when twisted onto the cup.
Turn the lid tightly clockwise.
• Make sure the unit is plugged in.
•
Rotate and press down on the cup to turn the unit on.
Unit doesn't turn on.
• Make sure the blade assembly is properly assembled to the cup and that
it is not misaligned.
•
Unplug the power cord from the electrical outlet and call customer
Unit doesn't turn off.
service for support.
•
Pulse ingredients for best results. Press down on the cup in short
Doesn't mix well.
intervals for even blending and chopping. For frozen ingredients, pulse in
short intervals of 2-5 seconds and repeat.
• Set the cup on a level surface. Place the lid or blade assembly on top of
Lid/blade assembly will not
the cup and align the threads so that the lid/blades sit flat on the cup.
properly align to the cup. Twist clockwise so that the lid/blades evenly align to the cup until you
have a tight seal.

Replacement Parts

ORDERING REPLACEMENT PARTS
To order additional parts and attachments, please visit our website: www.sharkninjamanuals.com or feel free to
contact customer service: 1-877-646-5288.
POSSIBLE REASONS & SOLUTIONS
www.sharkninjamanuals.com 13