Security Tronix ST-IP-TD1.4-B/W Quick Start Manual

ST-IP-TD1.4-B/W
QUICKSTART GUIDE
Please refer to the complete User
manual for more information
4 Access to the IP Camera via IE
1. Be sure to power the camera with the correct power supply
2. Make sure the device IP address is in the same LAN with the
router, the default IP address of the IPC is 192.168.1.168
3.Go to CD->IPCSearch.exe and copy it to your computer
4.Open IPC Search, click "Search", you will find the device IP,
and you also can modify the IP infor-
mation, see the picture on the left:
5.Factory default IP setting:
IP Address : 192.168.1.168
Subnet Mask : 255.255.255.0
Gateway : 192.168.1.1
User name : admin
Password : admin
6.After modifying IP, click "Search"
again, you will find the new IP of the your
device. Double-click the new IP, you can access to the IPC via
IE, or enter the IP Address in the address bar of IE, then click
"Enter", the download_OCX controls interface please see below
picture:
7.Please click here to download the OCX controls, as
is shown in the following picture:
Click run, the system will automati-
cally download the OCX, click "yes"
in the following picture:
1 Important Safety Information
Please be sure to read the following important safety infor-
mation before installing and use the product.
CAUTION:
RISK OF ELECTRIC SHOCK.
DO NOT OPEN
CAUTION:
TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT
REMOVE COVER OR BACK. NO USER SERVICEABLE
PARTS INSIDE. REFER TO OUALIFIED SERVICE PERSON-
CAUTION:
TO PREVENT ELECTRIC SHOCKS AND RISK OF FIRE
HAZARDS, DO NOT USE OTHER THAN SPECIFIED POWER
SOURCE.
Notes：
●The power supply must match the camera's requirement.
●A voltage surge protector is recomennded to protect the
camera from dangerous over-voltage enviorment such as
a lightning storm. (ST-VSP-4)
●In order to capture high quality pictures, the power sup-
ply's cable and video output cable should not be too long.
Then it will install the OCX，
when complete ,the window
below will pop up:
Click "OK" and refresh the page.
You will enter the login interface,
as is shown in the left picture:
Enter your username and pass-
word, you can start to access and
control your IP Camera.
5 Access to the IP Camera via Multi_window
Go to CD->find Multi_window.exe. Copy Multi_window.exe to
your computer and install it, then run it. See below:
1.Config:Group.See below:
Here you can add your IP Camer-
as and set the Capture Path. If you
forget the IP Address, you
can click "Search" to search
your IP Cameras. You can
select "List all ipcam" or
"List only unselect", then
2 Brief Introduction of the products
Specifications
Model ST-IP-TD1.4-PRO-B/W
1/3" Sony Low Illumination 1.3 Megapixel
Image Sensor
CMOS Sensor
Resolution 960P@25fps,720P@25fps
Minimum
1Lux
Illumination
S/N Ratio >50db
Focus Mode Manual
Day/Night IR cut filter with auto switch
Weatherproof IP65
Network 1 RJ45 Ethernet interface, 10/100M
Delay Within The LAN 0.3S
Frame Rate 25 FPS ( Adjustable)
Video
H.264 /JPEG
Compression
Protocols: TCP/UDP/RTSP/FTP/PPPOE/
Protocol
DHCP/DDNS/NTP/UPnP/SMTP
Onvif Support Onvif 2.0
User
Multi-user Classification Management
Permission
Power DC 12V/ DC 48V (PoE)
Consumption 3.0W
Lens 3.6mm / F.20 (2M)
IR Status IR LED: ¢5X24PCS IR range: 20M
Dimension (mm) 94(W) x69(H) x69(D)mm
Weight (g) 450G
Temperature
-4°～122°F
Humidity 0%-90%RH,Without Condensation
double click the IP info to add the camera.
You also can enter the IP Info manually in the "IPcam Infor-
mation area"
Then you can view the images and set the parameters of IP
Camera, such as Alarm, Video, Net, Camuser, Date, etc.
Please refer to Multi_window Customer Manual for detail.
2.View the images
After adding the devices, you can see the devices in "List" of
the main interface, you can double click the device to control it
to play or stop. See below picture:
You also can control
the devices in "Camera",
see the picture on the right:
6 Access to the IP Camera via Android mobile
Search and download the surveillance software "MEyepro" to
your mobile from electronic markets or the Mobile Assistant,
then install it. Then you can see the icon of the software
,click it to run.
1.The following picture shows the main
interface:
2.Live view
See the picture on the
right.
Features:
Advanced H.264 High profile compression
Internet Explorer browser enabled
Support several servers, IP address, DDNS, FTP,SMTP
Support single, dual, and triple stream
Support iPhone, iPad, Android remote monitor
Support ONVIF2.0
Reliability and compatibility
Low streams and high resolution image
3 Connection
DC12V
RJ45
switch/router/FOT
IPC PC1
ST-IP-TD1.4-B/W
Network Structure
Click the button "PTZ" , and you will see the PTZ function but-
tons, see below picture:
Button function:
Button Name Button Name
Play Switch channels
Snapshot PTZ Control
Local Record Zoom
Configure Focal
PTZ Iris
About
3.Device list
:Add device, Input Device name,
IP address or domain name, port,
username, password, Max Channel,
then click "OK" to finish and save.
:Edit device. Modify Device name,
IP address or domain name, port,
username, password, Max Channel,
then click "OK" to finish.
PC2