Use and Care Guide Liquid Propane Gas Grill Sears Item No. 415.16646900 This Grill is for Outdoor Use Only Safety • WARNING Parts • Use and Care • Read and follow all Safety, Assembly, • Assembly • and Use and Care Instructions in this...
DANGER WARNING CALIFORNIA PROPOSITION 65 If you smell gas: 1. Combustion by-products produced when using 1. Shut off gas to the appliance. this product contain chemicals known to the State of 2. Extinguish any open flame. California to cause cancer, birth defects, and other 3.
LP Tank USE AND CARE • The LP Tank used with your grill must meet the following requirements: • Use LP Tanks only with these required measurements: 12" DANGER (30.5cm) (diameter) x 18" (45.7 cm) (tall) with 20 lb. (9 kg.) capacity maximum.
LP Tank Exchange Connecting Regulator To The LP Tank 1. LP tank must be properly secured onto grill. (Refer to • Many retailers that sell grills offer you the option of replacing your empty LP tank through an exchange service. Use only assembly section.) those reputable exchange companies that inspect, precision fill, 2.
Leak Testing Valves, Hose and Regulator 1. Turn all grill control knobs to OFF. 2. Be sure regulator is tightly connected to LP tank. 3. Completely open LP tank valve by turning OPD hand wheel counterclockwise. If you hear a rushing sound, turn gas off immediately.
Safety Tips WARNING Before opening LP tank valve, check the coupling nut for tightness. For Safe Use Of Your Grill And To Avoid Serious When grill is not in use, turn off all control knobs and LP tank Injury: valve. •...
Ignitor Lighting CAUTION Do not lean over grill while lighting. 1. Open lid during lighting. • Putting out grease fires by closing the lid is not 2. Turn on gas Tank valve. possible. Grills are well ventilated for safety reasons. 3.
Before Your First Cookout • Plated wire grates: Wash grates with concentrated grill cleaner or use soap and water solution. Dry thoroughly and • Light burners, check to make sure they are lit, close the lid and store indoors between cookouts. warm up grill on HIGH for 15 minutes.
Storing Your Grill Cleaning the Burner Assembly • Clean cooking grates. Follow these instructions to clean and/or replace parts of burner • Store in dry location. assembly or if you have trouble igniting grill. • When LP tank is connected to grill, store outdoors in well- 1.
Indirect Cooking Indirect Cooking Instructions • Always cook with the lid closed. Poultry and large cuts of meat cook slowly to perfection on • Due to weather conditions, cooking times may vary. During the grill by indirect heat. The heat from selected burners cold and windy conditions the temperature setting may need circulates gently throughout the grill, cooking meat or poultry to be increased to insure sufficient cooking temperatures...
Grill Halogen Light LIGHT OPERATION INSTRUCTIONS 1. Make sure light switch on the control panel is in the “OFF” position. 2. Connect light plug to an extension cord, then put the extension cord plug into the outlet on the wall. 3.
Cleaning the Lens 1. Prior to cleaning, make sure the light switch is in the “OFF” position and the light plug is disconnected from the power supply. 2. Do not clean the glass lens when warm. Allow to cool before cleaning. Sudden change in temperature may cause cracking of the glass lens.
1 INNER INSERT, F/ TOP LID 80018532 2 RUBBER BUMPER, RECTANGULAR, 80006983 F/ LID 4 RUBBER BUMPER, ROUND, F/ LID 80006625 1 LOGO PLATE, KENMORE 80010544 1 BEZEL, F/ TEMPERATURE GAUGE 80004295 1 TEMPERATURE GAUGE 80007690 1 HARDWARE F/ TOP LID ASSEMBLY...
ASSEMBLY Attach the two locking casters at the rear of the bottom shelf and the two fixed casters at the front using the supplied wrench. Fixed caster Locking caster Bottom shelf Attach side panels to bottom shelf using three 1/4-20x1/2” screws, 7mm lock washers per panel. 7mm lock washer 1/4-20x1/2”...
Attach light adapter to back panel using four #8-32x3/8” screws, 4mm lock washers, 4mm flat washers and #8 nuts, shown A. Place lower back panel between side panels at rear of bottom shelf. Secure lower back panel to side panels using two 1/4-20x1/2”...
Insert front brace under control panel and between cart side panels. Secure using two 1/4-20x1½” screws, 7mm lock washers on each side. NOTE: MAKE SURE THAT THE FRONT BRACE IS MOUNTED AS ILLUSTRATED BELOW. 7mm Lock washer Qty.4 1/4-20x1½” screw Qty.4 7mm Lock 1/4-20x1½”...
Attach left side lower fascia to left side upper fascia using three #10x3/8” screws, 5mm lock washers and 5mm flat washers, shown A. Remove the three screws and washers which were attached on left side of firebox front, shown B. Insert flange on left side shelf into side shelf brackets on side of firebox, shown C.
On back of grill, place upper back panel between side panels and above lower back panel. Secure upper back panel, in lower holes, using one 1/4-20x1½” screw and 7mm lock washer on each side. In upper holes, using one 1/4-20x1½” screw and 7mm lock washer on each side, shown A.
Insert sideburner burner into left shelf. The stud on bottom of burner fits into rear small hole in sideburner drip pan on shelf, shown A. Secure burner to sideburner drip pan with one Wing nut, shown B. Make sure burner tube engages sideburner valve, shown C.
Inside of cart, insert rear shield tabs into slots next to grease tray opening on upper back panel, shown A. Attach front shield tabs(with holes) under front brace with two #8x3/8” self-tapping screws, shown B. self-tapping screw #8x3/8” Qty.2 front tab rear tab (w/hole) Note: some parts omitted...
Insert hinge pin on bottom of doors into hole in bottom shelf. Press upper hinge pin in front brace, align hinge hole on top of door, and release hinge pin into door. PRESS Top of door Right door Hinge pin on bottom of door Left door...
Install heat diffusers by sliding one end of each heat diffuser into slots at front of firebox and resting opposite end on pins in back of firebox. Note: Some parts omitted for clarity of illustration Front of firebox Heat diffuser Back of firebox Place cooking grates onto the firebox as shown.
LP CYLINDER IS SOLD SEPARATELY. Fill and leak check the cylinder before attaching to grill and regulator (see Use & Care section). Once cylinder has been filled and leak checked, place cylinder into hole in bottom shelf. Make sure cylinder valve is facing front of grill.
EMERGENCIES: If a gas leak cannot be stopped, or a fire occurs due to gas leakage, call the fire department. Emergencies Possible Cause Prevention/Solution Gas leaking from •Damaged hose. •Turn off gas at LP cylinder or at source on natural gas systems. If cracked/cut/burned anything but burned, replace valve/hose/regulator.
Troubleshooting (continued) Problem Possible Cause Prevention/Solution ELECTRONIC IGNITION: Burner(s) will not light using ignitor. •No spark, no ignition noise. • See Section I of Electronic Ignition System. (See Electronic Ignition Troubleshooting also) •No spark, some ignition noise. • See Section II of Electronic Ignition System. •Sparks, but not at electrode or at full •...
Troubleshooting - Electronic Ignition Problem (Ignition) Possible Cause Check Procedure Prevention/Solution SECTION I No sparks appear at •Battery not installed •Check battery orientation. •Install battery (make sure that “+” and “–” any electrodes when properly. connectors are oriented correctly, with “+” end up and “–”...
Get it fixed, at your home or ours! Your Home For expert troubleshooting and home solutions advice: www.managemyhome.com For repair – in your home – of all major brand appliances, lawn and garden equipment, or heating and cooling systems, no matter who made it, no matter who sold it! For the replacement parts, accessories and owner’s manuals that you need to do-it-yourself.