Subscribe to Our Youtube Channel
Related Manuals for Daktronics TI-2025
Summary of Contents for Daktronics TI-2025
- Page 1 TI-2025 & TI-2026 SEGMENT TIMERS DISPLAY MANUAL P1192 ED-16738 Rev 4 26 June 2018 201 Daktronics Drive Brookings, SD 57006-5128 www.daktronics.com/support 800.325.8766...
- Page 2 Daktronics trademarks are property of Daktronics, Inc. All other trademarks are property of their respective companies.
-
Page 3: Table Of Contents
Component Locations & Access ......................5 Replacing Digits ............................5 Adjusting the Horn Volume........................6 Replacement Parts ..........................6 Daktronics Exchange and Repair & Return Programs ������������������������������������������������������7 Exchange Program ..........................7 Repair & Return Program ........................8 Daktronics Warranty & Limitation of Liability ..................8 A Reference Drawings �������������������������������������������������������������������������������������������������������������9 Daktronics Warranty &... - Page 4 This page intentionally left blank.
-
Page 5: Introduction
Figure 1: Specifications Label Please have the assembly number, model number, and the date manufactured on hand when calling Daktronics customer service to ensure the request is serviced as quickly as possible. Knowing the facility name and/or job number will also be helpful. -
Page 6: Resources
Reference Drawing: System Riser Diagram ..................DWG-1007804 Daktronics identifies manuals by the DD or ED number located on the cover page. Daktronics Nomenclature Most display components have a white label that lists the part 0P-1127-0024 number (Figure 3). -
Page 7: Mechanical & Electrical Installation
The display will remain blank until it receives signal from a controller. Signal is provided in one of two ways: 1) via a 9-pin serial to 4-pin XLR cable (Daktronics part number 0A-1196-0095) connected between the J31 signal input on the side of the display and the jack on top of the All Sport 100 console, or 2) via radio transmission from the RC-50 controller to the built in antenna. -
Page 8: Troubleshooting
Troubleshooting Disconnect power before doing any repair or maintenance work on the display� Permit only qualified service personnel to access internal display electronics. Disconnect power when not using the display� Troubleshooting Table The table below lists potential problems with the display and indicates possible causes and corrective actions. -
Page 9: Component Locations & Access
Component Locations & Access Reference Drawing: Schematic: TI-2025/26 (120VAC) Segment Timer ........... DWG-274184 Component Location; TI-2025/2026, Segment Timer ........DWG-278310 DWG-278310 shows front, back, and side views of the display along with the location of vital components and the location of the hardware used to attach those components. -
Page 10: Adjusting The Horn Volume
0P-1192-0390 Horn Interface; 5-35V In, 120VAC Out 0P-1192-0399 Radio Antenna; 418 MHz A-2015 Toroid, 115/230V, 3.6 A w/ Bracket T-1132 Refer to Section 4: Daktronics Exchange and Repair & Return Programs (p�7) for information on exchanging or returning parts. Troubleshooting... -
Page 11: Daktronics Exchange And Repair & Return Programs
Fill out and attach the enclosed UPS shipping document. c� Ship the part to Daktronics. 3� The defective or unused parts must be returned to Daktronics within 5 weeks of initial order shipment� If any part is not returned within five (5) weeks, a non-refundable invoice will be presented to the customer for the costs of replenishing the exchange parts inventory with a new part. -
Page 12: Repair & Return Program
Repair & Return Program For items not subject to exchange, Daktronics offers a Repair & Return Program. To send a part for repair, follow these steps: 1� Call or fax Daktronics Customer Service� Refer to the appropriate number in the chart on the previous page. -
Page 13: A Reference Drawings
Refer to Resources (p�2) for information regarding how to read the drawing number. Any contract-specific drawings take precedence over the general drawings. Reference Drawings: Schematic: TI-2025/26 (120VAC) Segment Timer ........... DWG-274184 System Riser: TI-2025/26 Segment Timer ............DWG-274283 Component Location; TI-2025/2026, Segment Timer ........DWG-278310... - Page 14 This page intentionally left blank.
- Page 18 This page intentionally left blank.
-
Page 19: B Daktronics Warranty & Limitation Of Liability
Daktronics Warranty & Limitation of Liability This section includes the Daktronics Warranty & Limitation of Liability statement (SL-02374)� Daktronics Exchange and Repair & Return Programs... - Page 20 This page intentionally left blank.
- Page 21 EXCEPT AS OTHERWISE EXPRESSLY SET FORTH IN THIS WARRANTY, TO THE MAXIMUM EXTENT PERMITTED BY APPLICABLE LAW, DAKTRONICS DISCLAIMS ANY AND ALL OTHER PROMISES, REPRESENTATIONS AND WARRANTIES APPLICABLE TO THE EQUIPMENT AND REPLACES ALL OTHER WARRANTIES OR CONDITIONS, EXPRESS OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, ANY IMPLIED WARRANTIES OR CONDITIONS OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, OR ACCURACY OR QUALITY OF DATA. OTHER ORAL OR WRITTEN INFORMATION OR ADVICE GIVEN BY DAKTRONICS, ITS AGENTS OR EMPLOYEES, SHALL NOT CREATE A WARRANTY OR IN ANY WAY INCREASE THE SCOPE OF THIS LIMITED WARRANTY. THIS LIMITED WARRANTY IS NOT TRANSFERABLE. 2. Exclusion from Warranty Coverage This Warranty does not impose any duty or liability upon Daktronics for any: A. damage occurring at any time, during shipment of Equipment unless otherwise provided for in the Agreement. When returning Equipment to Daktronics for repair or replacement, End User assumes all risk of loss or damage, agrees to use any shipping containers that might be provided by Daktronics, and to ship the Equipment in the manner prescribed by Daktronics; B. damage caused by: (i)the improper handling, installation, adjustment, use, repair, or service of the Equipment,or (ii) any physical damage which includes, but is not limited to, missing, broken, or cracked components resulting from non‐electrical causes; altered, scratched, or fractured electronic traces; missing or gauged solder pads; cuts or clipped wires; crushed, cracked, punctured, or bent circuit boards; or tampering with any electronic connections, provided that such damage is not caused by personnel of Daktronics or its authorized repair agents; C. damage caused by the failure to provide a continuously suitable environment, including, but not limited to: (i) neglect or misuse; (ii) improper power including, without limitation, a failure or sudden surge of electrical power; (iii) improper air conditioning, humidity control, or other environmental conditions outside of the Equipment’s technical specifications such as extreme temperatures, corrosives and metallic pollutants; or (iv) any other cause other than ordinary use; Copyright © Daktronics, Inc. SL-02374 Rev 12 19Nov15 Page 1 of 2...
- Page 22 Limitation of Liability Daktronics shall be under no obligation to furnish continued service under this Warranty if alterations are made to the Equipment without the prior written approval of Daktronics. It is specifically agreed that the price of the Equipment is based upon the following limitation of liability. In no event shall Daktronics (including its subsidiaries, affiliates, officers, directors, employees, or agents) be liable for any claims asserting or based on (a) loss of use of the facility or equipment; lost business, revenues, or profits; loss of goodwill; failure or increased cost of operations; loss, damage or corruption of data; loss resulting from system or service failure, malfunction, incompatibility, or breaches in system security; or (b) any special, consequential, incidental or exemplary damages arising out of or in any way connected with the Equipment or otherwise, including but not limited to damages for lost profits, cost of substitute or replacement equipment, down time, injury to property or any damages or sums paid to third parties, even if Daktronics has been advised of the possibility of such damages. The foregoing limitation of liability shall apply whether any claim is based upon principles of contract, tort or statutory duty, principles of ...
Need help?
Do you have a question about the TI-2025 and is the answer not in the manual?
Questions and answers