Techly I-TOOL-SD-091TY User Manual

User's Manual
EN
Manuale d'istruzione
IT

FEATURES:

EN
This soldering station is an ideal entry level soldering station
for hobbyists.
Heater: Mica, 150°C-480°C (48W)
Temp. Control: Rotary setting by knob

ATTENTION:

On first time use the soldering iron may produce smoke,
this is just grease used in manufacturing burning off.
It is normal and should only last for approx. 10 minutes.
It is not harmful to the product or user.

CARE OF THE TIP:

• Always keep tips coated with tin to ensure a long service life.
• Do not keep the iron at high temperature for a long time.
• Never clean the tip with coarse materials.
• Never cool it in water.
• Remove the tip and clean every twenty hours of use, or at least
once a week, and remove any loose build up in the barrel.
• Do not use fluxes containing chloride or acid.
Use only rosin or activated resin fluxes.
• Do not use any compound or anti-seize materials.
• Handle the heated soldering iron with extreme care, as the high
temperature of the iron can cause fires or painful burns.
• Never file the specially-plated tip.

MAINTENANCE:

• This tool must be placed on its stand when not in use.
• If the supply cord is damaged, it must be replaced
by the manufacturer or its service agent or a similarly qualified
person in order to avoid hazard.

OPERATION:

• Unpack the soldering station and check all parts.
Damaged parts must not be put into operation.
• Put the holding rack for the soldering iron sideways
in the soldering station, wet the cleaning sponge
in the sponge rack with water.
• Put the soldering iron in the holding rack
• Place the soldering station on a solid and dry surface.
• Connect the mains plug to a socket and turn on the soldering
station by using the power switch (I=ON/0=OFF).
When turned on, the power switch is lit.
• Always put the soldering iron on the holding rack when
it is heating up or during breaks from soldering.
• Make sure the workbench for soldering is clean.
• Only use solder for electronics. Acidic solder can damage
the soldering tip or the work piece.
• Regulate the desired temperature of the soldering iron
with the adjusting knob.
• The color-coded areas are equal to following temperatures:
Yellow >= 160°C
Light Orange 180°C to 350°C
Deep Orange 350°C to 450°C
Red <=550°C
TEMPERATURE CONTROLLED
STAZIONE DI SALDATURA CON
• Lower the temperature during breaks, this saves energy
and extends the durability of the soldering tip.
• Wait for about 10 minutes until the soldering tip reaches
the setting temperature, test the temperature by touching
the soldering tip with solder. If the solder melts away easily,
you can start soldering.
• Tin the hot soldering tip with solder; wipe off excessive solder
on the wet cleaning sponge.
• Heat up the to-be-soldered part with the soldering tip
and add solder.
• Wait for the hot solder to cool down.
• Clean the soldering tip on the wet sponge after each soldering.
• After the soldering is done, put back the soldering iron
in the rack and turn off the soldering Station at the main switch.
• Do not file off the soldering tip, or it will be damaged.
• Never touch the hot soldering tip.
• Let the soldering iron cool down after use.
• The soldering iron should not be dunked into water.
• During breaks, the soldering iron has to be placed
in the holding rack.

TIP REPLACEMENT

Note: Tip replacement or cleaning should be done only when
the iron is at room temperature or below. The tip can be changed
or replaced simply by unscrewing the knurled nut barrel assembly.
The station must be switched off and allowed to cool before
and during this operation, as damage may result if the system
is left on without the tip inserted, after removing tip, remove
any oxide dust that may have formed in the tip retaining area
of the barrel. Be careful to avoid getting dust in your eyes.
Care should be taken not to over tighten as this would damage
the element.

GENERAL CLEANING

The outer case of the iron or station may be cleaned with a damp
cloth using small amounts of liquid detergent Never submerse
the unit in liquid or allow any liquid to enter the housing.
Never use solvent to clean the case.

WARNING INSTRUCTIONS:

• The appliance is not a toy, and must be kept out of children's reach.
• Before cleaning the appliance or changing the filter,
always unplug it. Unscrewing the housing is not permitted.
• This appliance is not intended for use by persons (including
children) with reduced physical, sensory or mental capabilities,
or lack of experience and knowledge, unless they have been
given supervision or instruction concerning use of the appliance
by a person responsible for their safety.
• Children should be supervised to ensure that they
do not play with the appliance.
• If the supply cord is damaged, it must be replaced
by the manufacturer, its service agent or similarly qualified
persons in order to avoid a hazard.
CARATTERISTICHE:
IT
Questa stazione di stagnatura è uno strumento ideale
per principianti e hobbisti.
Riscaldamento: Mica, 150°C-480°C (48W)
Controllo della temperatura: regolazione rotatoria tramite
manopola.
ATTENZIONE:
Al primo utilizzo la stazione di stagnatura potrebbe produrre
del fumo, altro non è che il materiale lubrificante usato
in produzione che sta bruciando. Questo è normale e dovrebbe
durare approsimativamente solo per 10 minuti.
Non è pericoloso nè per il prodotto nè per l'utilizzatore.
MANUTENZIONE DELLA PUNTA:
• Mantenere sempre le punte coperte con della stagnola
per assicurarne una lunga durata.
• Non tenere il ferro ad elevate temperature per troppo tempo.
• Mai pulire la punta con materiali ruvidi.
• Mai raffreddare in acqua.
WWW.TECHLY.COM
SOLDERING STATION
CONTROLLO TEMPERATURA