CytoTherm CT-4T Owner's Manual
  1. Manuals
  2. Brands
  3. CytoTherm Manuals
  4. Laboratory Equipment
  5. CT-4T
  6. Owner's manual

CytoTherm CT-4T Owner's Manual

Hide thumbs

Advertisement

Table of Contents

Tel 800 747-9699 or 609 396-1456 Fax 609 396-9395
Email serve@cytotherm.com Web www.cytotherm.com
CytoTherm-4T
PLASMA THAWING
ROCKING WATER BATH
with TURBO ACTION
CT-4T
Model
Owners Manual
Version 409 and higher.
Corral mounts on shelf.
Each CytoTherm product is produced under rigid quality control standards. This unit is fully warranted for a period of two
years from the date of purchase. Call 609 396-1456 or 800 747-9699 for help. If necessary send unit to:
CytoTherm
110 Sewell Ave. Trenton, NJ USA Tel 609 396-1456 Fax 609 396-9395
Please mail in your warranty card.
Please record the following:

TABLE OF CONTENTS

1
Specifications
2
2
4
4
5
SPECIFICATIONS
Thawing temperature adjustable 25
o
C safety thermostat. Accuracy 0.1
Watt, Available in 120 Volt or 230 Volts, 50 or 60 Hz. (must be grounded). Will thaw 300 ml. & 450 ml. plasma
bags.
CytoTherm
110 Sewell Ave.
W A R R A N T Y
Serial No. ___________ Date of Purchase _________
o
o
C to 40
C. Preset to 37.0
Trenton NJ 08610 USA
Draw\Instruct CT Products \CT4TinsN.docx 27 Jun 16
6
Troubleshooting
7
Maintenance
8
Parts List
8
Technician Functions
9
Safety Features
9
Accessories
10
Wiring Diagram
o
C. Overtemp Alarm 1.0
o
C. Easy to do, digital temperature calibration. Power 770
o
C over thawing

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the CT-4T and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for CytoTherm CT-4T

Summary of Contents for CytoTherm CT-4T

  • Page 1: Table Of Contents

    W A R R A N T Y Each CytoTherm product is produced under rigid quality control standards. This unit is fully warranted for a period of two years from the date of purchase. Call 609 396-1456 or 800 747-9699 for help. If necessary send unit to: CytoTherm 110 Sewell Ave.

  • Page 2: Description

    The CT-4T comes with one CORRAL that will thaw 1 to 6 plasma bags at a time. A second CORRAL will let you thaw 6 more plasma bags for a total of up to 12 plasma bags at a time. The operator never comes in contact with the water in the bath when handling the plasma bags.
  • Page 3 Make sure that the DRAIN Valve is closed (horizontal). Fill the BATH with tap water to the bottom of the SHELF if you have one CORRAL mounted and to the screw of the shelf if you have 2 CORRALs mounted. If your tap water contains a lot of lime, use distilled or de-ionized water, add a pinch (0.01gr.) of salt to make the water conductive so that the level sensors will work.

  • Page 4: Operation

    OPERATION Wait for the water to heat up to 37.0 For your protection, use gloves when working with any blood products. Flat-frozen plasma units can be thawed without an overwrap bag. Hold a bag of flat-frozen plasma (bare or overwrapped) with the ports up and the label on the plasma unit away from the center of the CORRAL.

  • Page 5: Modes

    ENTER, the heater will heat continuously and the pumps will turn on. When the temperature reaches 1.0C above the target temperature the alarm will sound. Turn Off the unit. If alarm does not sound, contact CytoTherm. Alarm test should be performed every 3 months as part of unit maintenance.
  • Page 6 TOO HOT is an audible and displayed alarm condition that indicates that the bath temperature is 1.0C higher than the set temperature. If the operator pours hot water into the bath he/she will trigger this alarm. This should never happen in normal operation. If it does, contact CytoTherm.
  • Page 7 Turn Off the unit. If alarm does not sound, contact alarm does not sound, contact CytoTherm. Alarm test should be performed every 3 months as part of unit maintenance. CytoTherm. Alarm test should be performed every 3 months as part of unit maintenance.
  • Page 8 PARTS LIST CT-4T 14-MP Pump, Magnetic DP-SW Switch, 2-pole 14-77 Heater (2 needed) C-TH Safety Thermostat CT4-PC Printed Circuit Board C4-DISP Display C4T-BTH Bath Section C4-UMB Wiring Harness C-RM Rocking Motor C4T-PM Program Module C4-TS Temperature Sensor C4T-CLM Clamp ( bag to cor.)
  • Page 9 SAFETY FEATURES WATER LEVEL SENSOR The unit will display LOW WATER and beep if there is not enough water to cover the level sensor inside the bath, a screw located 3/4" above the temperature sensor. The heat will also turn off. The water must be conductive in order for the level sensor to work.

  • Page 10: Temperature

    Strain Relief mounted on connector = 240V MOV 100V uses dual transformer. see Dwg# 361 Male Housing Female Pins Wiring CT-DR / CT-4T D 351B.kcw File \Draw#\D#351.kcw Home 30 Nov 2000 120/100V wired as shown 1 Jul 02. 8A Fuses for 120/100...

Table of Contents