Download Print this page

Barrette 73045676 Quick Start Manual

Advertisement

Available languages

Available languages

Quick Links

2x4' DECORATIVE SCREEN PANEL CORNER EXTENSION 
FRAME KIT ASSEMBLY INSTRUCTIONS 
Warning 
• Read all instructions before installing the product. 
• When using tools, refer to the manufacturer's safety instructions. 
• Make sure the posts will be held in place by a sturdy structure and 
reinforce the surface it stands on as necessary. 
• Improper product installation can cause injury. Always wear safety 
glasses when cutting, drilling and assembling the product.  
• Improper installation may cause product damage or injury to the 
person performing the installation. 
• Check the local building code to determine if the product meets the 
pool fencing requirements. 
NOTE 
• DO NOT assemble the product if there are missing or damaged parts. 
• DO NOT return the product to the store.  For help or replacement 
parts, call 1‐800‐336‐2383.  
 
 
Before You Begin:   This product is intended for decorative 
use only.  It is the responsibility of the installer to meet 
and/or exceed all code and safety requirements and to obtain 
required building code permits as necessary. 
Kit contains:  
‐ (1) Aluminum Corner Post 
‐ (2) Mid H‐Channels (Rails) 
‐ (2) Top/Bottom U‐Channels (Rails) 
‐ Surface Mount Kit 
‐ Post Cap 
‐ Hardware (Screw kit) 
‐ #2 square drive drill bit 
‐ #3 Phillips drive drill bit 
‐ 1/8" Drill Bit 
Required, Sold Separately: 
‐ (3) 2x4 Decorative Screen Panels 
‐ 3/8" Bolts/Screws for mounting base plates to a structure 
Optional to Connect Frame Kits, Sold Separately: 
‐ Additional 2x4 Frame kit 2x4 #73040779 
‐ Line Post Extension Kit #73045675 
This is not a complete set, but only an extension. In order to have a 
complete structure, you must first buy the 2x4' panels Frame kit  
# 73040779. Then, you can add the desired number of extensions kits.
  
Tools Needed:
‐ Drill 
‐ Pencil 
‐ Tape Measure 
‐ Rubber Mallet 
‐ 3" Spacer Blocks 
‐ 1/8" Metal Drill Bit
Step 1
Install base plates to bottom of posts. Locate bottom post with 
pre‐tapped holes and attach the bottom plate to that end.  
Using only the #3 Phillips drive drill bit provided in surface 
mount kit, screw base plate to bottom of post through the 4 
screw bosses. Drill should be set to low speed when securing 
plates to post. 
Step 2
Place two 3" spacer blocks to support bottom rail. Take bottom 
rail and insert into the groove of first post, resting on the 3" 
spacer blocks. Note: This step is to set distance in between posts. 
Step 3
Take post and insert opposite side of bottom rail into the 
channel of this post. Be sure rail is fully inserted into the post. 
Set post in desired location. Ensure mounting surface has 
proper structure to hold post before fastening in place.  Use 
the post assembly to mark the holes for the surface mounting 
plate. Mark and drill holes for appropriate 3/8" fasteners 
(fasteners will vary depending on mounting surface). 

Advertisement

loading
Need help?

Need help?

Do you have a question about the 73045676 and is the answer not in the manual?

Questions and answers

Summary of Contents for Barrette 73045676

  • Page 1 Required, Sold Separately:  Step 2 ‐ (3) 2x4 Decorative Screen Panels  Place two 3" spacer blocks to support bottom rail. Take bottom  ‐ 3/8” Bolts/Screws for mounting base plates to a structure  rail and insert into the groove of first post, resting on the 3"  Optional to Connect Frame Kits, Sold Separately:  spacer blocks. Note: This step is to set distance in between posts.  ‐ Additional 2x4 Frame kit 2x4 #73040779  ‐ Line Post Extension Kit #73045675  This is not a complete set, but only an extension. In order to have a  complete structure, you must first buy the 2x4’ panels Frame kit   # 73040779. Then, you can add the desired number of extensions kits.    2x4’ DECORATIVE SCREEN PANEL CORNER EXTENSION  FRAME KIT ASSEMBLY INSTRUCTIONS  Warning  • Read all instructions before installing the product.  Tools Needed: • When using tools, refer to the manufacturer’s safety instructions.  ‐ Drill  • Make sure the posts will be held in place by a sturdy structure and  Step 3 ‐ Pencil  Take post and insert opposite side of bottom rail into the  reinforce the surface it stands on as necessary.  ‐ Tape Measure  channel of this post. Be sure rail is fully inserted into the post.  • Improper product installation can cause injury. Always wear safety  ‐ Rubber Mallet  Set post in desired location. Ensure mounting surface has  glasses when cutting, drilling and assembling the product.   ‐ 3" Spacer Blocks  proper structure to hold post before fastening in place.  Use  • Improper installation may cause product damage or injury to the  ‐ 1/8” Metal Drill Bit the post assembly to mark the holes for the surface mounting ...
  • Page 2   Step 4   Step 5   Locate where to pre‐drill  Once screws are secure in both  a hole through post and  posts, slide decorative screen      rail as shown below.  panel in‐between posts in  Pilot holes for screws  grooves from top until it rests in  should be located  the bottom U‐Channel.   directly on the  intersection of small  Step 6 groove of the post and  Slide H‐Channel in the groove  channel. Be sure not to  from the top, resting it on the top  drill all the way through  of the Decorative Screen Panel.     the back side of the post. Lift H‐Channel up 1/8" (to allow  for expansion and contraction),  then pre‐drill a hole following  same process in step 4. Screw  should be installed directly on the  small groove of the post,  connecting with the H‐Channel.  Step 7 Repeat steps 5 & 6 for middle and top panel. Note: Always use  a tape measure to verify rails are equal space from each other  and that they are level. Step 4 continued  Using the 1/8” drill bit provided, pre‐drill pilot hole as  indicated above. ...
  • Page 3 Requis, vendu séparément :   Étape 2 :  ‐ 3 Panneaux décoratifs Barrette 2x4  Placer les deux blocs d'espacement de 3 po afin de supporter la  ‐ Vis/boulons de 3/8 po pour plaque de montage sur une structure  traverse inférieure. Prendre la traverse inférieure, la glisser dans  Optionnel, pour ajouter des ensembles de cadres vendus séparément :  la rainure du premier poteau et la déposer sur les blocs  ‐ Jeu de structure pour panneaux 2x4’ #73040779 additionnel  d'espacements. Remarque : cette étape sert à définir la distance  ‐ Jeu d’extension de structure pour installation en ligne #73045675  entre les poteaux.  Ceci n’est pas un ensemble complet, mais uniquement une extension.  Afin d’avoir une structure complète, il faut en tout premier lieu acheter  le jeu de structure pour panneaux 2x4’ #73040779. Par la suite, vous  pouvez ajouter le nombre de jeux d’extension désiré. INSTRUCTIONS D’ASSEMBLAGE POUR JEU D’EXTENSION EN  COIN POUR PANNEAUX 2x4’  Avertissement  • Lire toutes les instructions avant l’installation du produit.  • Lors d’utilisation d’outils, se référer aux instructions de sécurité du  manufacturier.  • S’assurer d’avoir une prise solide et si nécessaire, solidifier la structure  au sol.     Outils nécessaires :  Étape 3 :  ‐ Perceuse  • Une mauvaise installation du produit peut causer des blessures.  Prendre le poteau et y insérer le bout opposé de la traverse  ‐ Crayon  Toujours porter des lunettes de sécurité lors de la coupe, du perçage et de  inférieure. S'assurer que la traverse est complètement insérée  ‐ Foret à métal de 1/8 po (3mm)  l’assemblage du produit.  ...
  • Page 4   Étape 5 : Une fois que les vis sont bien fixées dans    Étape 4 :   les deux poteaux, faire glisser le panneau  Vérifier l’emplacement pour le  décoratif entre les poteaux dans les    pré‐perçage du trou au travers du  rainures du haut jusqu'à ce qu'il repose  poteau et de la traverse tel que  dans la moulure inférieure en U.   montré ci‐dessous.  Les trous  Conseil: S'assurer que les panneaux sont  pilotes devraient être localisés  placés dans la direction désirée avant le  directement sur l’intersection de  montage. la petite rainure du poteau et celle  de la traverse en prenant soin de  Étape 6 : ne pas transpercer la face  Glisser la moulure en H dans la rainure à  opposée du poteau.   partir du haut, la déposant sur le dessus  du panneau décoratif. Soulever la  moulure en H de 1/8 po pour permettre  l'expansion et la contraction, puis pré‐ percer un trou en suivant le même  procédé qu’à l’étape 4.  La vis doit être  installée directement sur la petite  rainure du poteau, en raccord avec la  moulure en H. Étape 7 : Répéter les étapes 5 et 6 pour le panneau du milieu et du haut.   Remarque : Toujours utiliser un ruban à mesurer pour vérifier que  les traverses sont à égale distance l'une de l'autre et qu'elles soient ...