Panasonic HG-S Instruction Manual

Contact-Type Digital Displacement Sensor / Sensor Head
Thank you very much for purchasing Panasonic products. Read this Instruction Man-
ual carefully and thoroughly for the correct and optimum use of this product. Kindly
keep this manual in a convenient place for quick reference.
Never use this product as a device for personnel protection.
When using devices for personnel protection, use products that meet the laws
and standards for personnel protection that apply in each region or country, such
as OSHA, ANSI and IEC.
This document provides a brief summary of mounting and other related information.
For detailed information, refer "our web site (https://panasonic.net/id/pidsx/global) ".
1 STANDARDS AND REGULATIONS
This product conforms to the standards and regulations below.
<European Directives>
EMC Directive
2 CONTENTS OF PACKAGE
Sensor head
Mounting nut
Sensor head fastening wrench
Rubber bellows ( only)
Instruction Manual (English / Japanese, Chinese / Korean)
General Information for Safety, Compliance, and Instructions(23 languages)
3 DESCRIPTION OF PARTS
Sensor head connection cable connector
Operation indicator (Orange / Green)
Mounting nut
Rubber bellows
Probe
4 MOUNTING
When tightening the mounting nut, take care not to damage the rubber bellows.
If the rubber bellows is deformed, a load will occur when the spindle operates
and damage may result.
to the thickness of the housing.
1. Open a hole in the housing in which the sen-
sor head will be mounted.
HG-S1010 R HG-S1110 R
HG-S1032
HG-S1050
2. Insert the sensor head into the hole you
opened in the housing, and fasten lightly
with the provided mounting nut.
INSTRUCTION MANUAL
MJE-HGS1010 No.0074-49V
WARNING
Housing thickness
Mounting hole Housing thickness
0.015
ø8H7 mm 6.5 12.5mm
0
6.5 10.5mm
0.018
ø12H7 mm
0
6.5 12.5mm
Mounting nut
(Accessory)
Installation of mounting nut attachment
Housing
HG-S1010 R
HG-S1032
HG-S1050
3. Fasten the sensor head.
When fastening the sensor head, tighten the
mounting nut with a wrench while holding the
sensor head in place with the sensor head
fastening wrench as shown at right.
Tighten to a torque of 12.5N·m or less
(HG-S1032 / HG-S1050: 15N·m or less).
4. Make sure that the rubber bellows has not
become deformed as shown at right.
1 pc.
If the rubber bellows is deformed, restore the
1 pc.
normal shape by rotating the bellows or oth-
1 pc.
erwise.
1 pc.
2 pcs.
1 pc.
Connecting the sensor head connection cable
When attaching the connector, make sure it is firmly tightened. If loose, the
When disconnecting, always make sure that the fastening ring has been com-
pletely loosened before pulling out the cable.
Risk of damage if you pull the cable with excessive force (15N or more) with the
fastening ring tightened.
How to connect
1. Insert the sensor head connection
cable into the connector for the
sensor head connection cable on
the sensor head.
2. Turn the fastening ring on the sen-
sor head connector in the direction
How to remove
1. Turn the fastening ring on the sen-
sor head connector in the direction
shown to loosen the ring.
2. Grasp the connector and pull up to
remove the cable.
5 SPECIFICATIONS
Type
Mounting hole
Model No.
Position detection method
Measurement range
Stroke
Downward
mount
Measur-
ing force
Upward mount
(Note 1)
(Note 2)
Side mount
Resolution
Sampling cycle
Indication
accuracy
(P-P)
Hot swap function
Protective structure
Ambient temperature
Ambient humidity
Mechanical life (Note5)
Tip deviation amount
Grounding method
Material
Weight (main unit only)
2)
3) Typical value near center of measurement.
4) Excludes damage and deterioration to the rubber bellows due to external causes.
5) Typical value in a clean environment in which there is no contact with liquids such as water or oil, and no set-
tling of particulate matter.
Mounting nut with the
thread facing down
A
Thread
HG-S1110 R
1. Insert
1. Loosen
General purpose
Low measuring
Standard type
force type
HG-S1010 HG-S1010R
Optical absolute linear encoder method
1.65N or less 0.35N or less
1.10N (Note 3) 0.30N (Note 3)
1.35N or less
-
0.85N (Note 3)
1.50N or less 0.25N or less
0.95N (Note 3) 0.20N (Note 3)
0.5μm
Full range 2.0μm or less
Limited range 1.0μm or less (any 60μm)
IP67 (IEC) (Note 4) -
-10 to +55°C (No dew condensation or icing allowed), Storage: -20 to +60°C
35 to 85% RH, Storage: 35 to 85% RH
100 million times or more (reference value)
35μm (typical value)
Capacitor grounding
Body: Zinc, Holder: Stainless steel, Spindle: Tool steel, Probe: Ceramic, Rubber
bellows: NBR (black)
is standard state without the rubber bellows.
Mounting nut with the
thread facing up
B
Housing
Thread
Housing thickness
A B
6.5 10mm 10 12.5mm
8.5 10.5mm
6.5 8.5mm
8.5 12.5mm
Sensor head
fastening wrench
(Accessory)
Wrench
2. Tighten
fastening ring
2. Pull out
10mm type
High precision
Low measuring
Standard type
force type
HG-S1110 HG-S1110R
10mm
10.5mm or more
1.65N or less 0.35N or less
1.10N (Note 3) 0.30N (Note 3)
1.35N or less
-
0.85N (Note 3)
1.50N or less 0.25N or less
0.95N (Note 3) 0.20N (Note 3)
0.1μm
1ms
1.0μm or less
0.5μm or less (any 60μm)
Incorporated
IP67 (IEC) (Note 4) -
Approx. 80g