Related Manuals for Acer Veriton X6660G
Summary of Contents for Acer Veriton X6660G
- Page 1 Veriton X6660G (VX6660G) / Veriton X4660G (VX4660G) Veriton X4665G (VX4665G) / Veriton X2665G (VX2665G) Veriton X2660G (VX2660G) Recycling Guide...
-
Page 2: Table Of Contents
Disassembly Procedure ………………………………………………………………………………………………….……3 Troubleshooting …………………………….………………………………………….………………………………….……16 Exploded diagrams ….………………………………………………………………………………………………….…..…19 FRU (Field Replaceable Unit) List…………………………………………………………………………………………20 To update your software ….………………………………………………………………………………………….…….21 To remove your personal data ……………………………………………………………………………….……….….21... -
Page 3: Disassembly Procedure
Disassembly Procedure Safety Guidelines This chapter contains step by step procedures on how to remove and de-install components from the computer. Use the following safety guidelines to ensure your personal safety. Each procedure included in this chapter assumes that you are preparing your computer for recycling and disposal. By performing any of these procedures you acknowledge that any remaining warranty applicable to your computer will be voided. - Page 4 WEEE Annex VII Component These components are classified as requiring selective treatment. Pre-disassembly Instructions Do the following prior to starting any maintenance procedures: 1. Place the system on a stable work surface. 2. Remove AC power cord from the system and peripherals 3.
- Page 5 Chassis Door Removal Remove the two (2) screws from the chassis door Remove the 2 screws Remove the left side cover...
- Page 6 ODD and card reader Module Removal 2. Remove the ODD Disconnect the ODD SATA cables and ODD power-cables from the rear of ODD Press the tail of ODD to pushing it out of chassis Remove the ODD...
- Page 7 HDD Removal 3. Remove HDD Disassemble front bezel Disconnect the SATA cables and SATA power-cables from HDD Remove two screws fastening HDD cage...
- Page 8 3.4 Press the HDD cage down and pull it out Pull green rack out from HDD cage 3.6 Remove HDD from green rack...
- Page 9 ODD tray and Card reader Removal 4. Disassemble ODD tray 4.1 Remove seven screws fastening ODD tray 4.2 Lifting up the ODD tray to remove it 4.3 Disconnect card reader cable from MB...
- Page 10 4.4 Remove two screws fastening FIO bracket then remove FIO bracket from chassis 4.5 Remove two screw and pull SD card reader out...
- Page 11 VGA card Removal Remove VGA Card Remove a screw and open the PCI bracket Press the PCI slot latch down and lift up the VGA card...
- Page 12 PSU Removal Remove internal PSU 6.1 Cut the cable ties to release cables and disconnect ATX_12V and ATX_power cable on MB 6.2 Remove four screw fastening PSU and pull it out 6.3 Remove a screw to disassemble PSU bracket...
- Page 13 MotherBoard, MEM, CPU, Cooler, WLAN, SSD, RTC Battery Removal 7. Remove the Main Board 7.1 Disconnect LPT and COM cable from M/B 7.2 Disconnect intrusion alarm and panel cables from MB 7.3 Disconnect SATA and SATA-power cables from MB...
- Page 14 7.4 Release the four latch show bellow then remove the Memory 7.5 Remove eight screws and remove the MB NOTE: Circuit boards >10 cm² has been highlighted with the yellow rectangle as above image shows. WEEE Annex VII component 7.6 Remove a screw and pull M.2 SSD card out then remove thermal pad.
- Page 15 7.7 Remove the four captive screws fastening CPU cooler and disconnect fan power cable from MB then remove CPU cooler 7.8 Unlock CPU socket latch and remove CPU 7.9 Remove the battery NOTE: RTC battery has been highlighted with the yellow circle as above image shows.
-
Page 16: Troubleshooting
Troubleshooting This chapter provides troubleshooting information for the Veriton X series Service Guide Power-On Self-Test (POST) POST Error Messages List Power-On Self-Test (POST) Each time you turn on the system, the Power-on Self Test (POST) is initiated. Several items are tested during POST, but for the most part transparent to the user. - Page 17 POST Error Messages List If you cannot run the diagnostics program tests but did receive a POST error message, use “POST Error Messages List "to diagnose system problems. If you did not receive any error message, look for a description of your error symptoms in “Error Symptoms List”.
- Page 18 Memory test fail If POST detects an error during memory testing, additional information appears giving specifics about the type and location of the memory error. Override enabled - If the system cannot boot using the current CMOS configuration, the BIOS can override the Defaults loaded current configuration with a set of BIOS defaults designed for the most stable, minimal- performance system operations.
-
Page 19: Exploded Diagrams
Exploded Diagrams Figure 1 System Exploded Diagram... -
Page 20: Fru (Field Replaceable Unit) List
FRU (Field Replaceable Unit) List Please contact your local service center to find out how to obtain the part or replace your device... -
Page 21: To Update Your Software
To update your software Please visit http://go.acer.com/?id=17883 To remove your personal data Option 1: Select Start > Settings > Update & Security > Recovery. Under Reset this PC, select Get started. Open Recovery settings. Option 2: Restart your PC to get to the sign-in screen, then press and hold down the ...