ATTENTION: This shelter product is manufactured with quality materials. It is designed to fit the ShelterLogic custom fabric cover included. ® , LLC ShelterLogic Shelters offer storage and protection from damage caused by sun, light rain, tree sap, animal - bird excrement ®...
Page 4
Basic Frame Assembly NOTE: FRAME EXTENSION KIT 22'x20'x10' is the base frame dimension. Your model may have more middle ribs than shown in the illustration on pg.2. You will receive one extra rib for every extra 4 ft. of building length that you purchase. The basic frame assembly will remain the same. The cover will be the correct size for the length of the building.
Page 5
11102 STEP 5: INSTALL SIDE RAILS AND SHELTERLOCK™ STABILIZER BLOCKS Fig. 5 11102 With help move the first end rib into the desired staked area. Place the ShelterLock on the upright as shown in Fig. 5. From the outside of the rib insert the bolt through the upright and then through the ShelterLock.
Page 6
STEP 8: SECURE BASE FEET Fig. 8 Depending on the model you have purchased, your base feet will either fit onto the outside of the leg pole or slide into the bottom of the leg pole. After installing the base feet line up the holes in the leg to the holes in the feet and secure with the hardware indicated in Fig.
Page 7
STEP 11: INSTALLING THE COVER ON THE FRAME: Fig. 11A, 11B, 11C & 11D Lay the cover on the ground next to the frame with the inside of the cover (the side with the pipe pockets) facing down and the webbing on the front and rear of the corner of the building.
Page 8
NOTE: ShelterLogic logo should line up on the left front and right rear corners near the top rail. If it is not legible and positioned as shown above as “incorrect”, the cover has not been put on the frame correctly.
Page 9
Assemblement de la charpente #78431 22'x20'x10' Garage Largeur Double Français Includes: #107133 (Charpente) #117133 (Kit de couverture gris) Part # Qty. Liste des pièces : Tubes de couverture bout normal 45"L 11105 Tubes d’extension 59.5"L 11068 11102 50.5"L Tubes transversal à bout raffiner 48.5"L...
Page 12
Assmenblement de la charpente Remarque : Kit d’extension 22'x20'x10' est la charpente de base. Votre model peut avoir plus d’ossature que montré dans l’illustration sur la page 2. Vous recevrez une ossature de plus pour tout les 4 pieds d’extension. La construction restera la même. La couverture sera de la taille du model complet.
Page 13
11102 Etape 5: INSTALLER LES BARRES DES COTÉS ET LES BLOQUES STABILISATEURS SHELTERLOCK™ Détail 5 11102 Ériger la première ossature de bout dans l’emplacement prévue. Positionner le Shelterlock sur le tube vertical comme montré dans le détail 5. En commençant de l’extérieur, passer le boulon au travers du poteau et du Shelterlock.
Page 14
Etape 8: SÉCURISEZ LES PIEDS Détail 8 Fixez avec boulon & Dépendant du model que vous avez achetez, les pieds irons ou à ecrous l’extérieure la jambe, ou ce glissera au bas de la jambe. Après avoir installé les pieds, aligner les trous des jambes avec ceux des pieds et sécuriser les avec la quincaillerie indiquer dans le détail 8.
Page 15
Etape 11. INSTALLER LA COUVERTURE SUR LA CHARPENTE : Détail 11A, 11B, 11C & 11D Poser la couverture sur le sol a coté de l’abri avec l’intérieur de la couverture (le coté avec les poches) vers le sol, et avec les sangles vers l’avant et l’arrière de la charpente.
Page 16
Remarque : Le logo Shelterlogic devrait être aligné des 2 cotés, à la hauteur de la porte. Si il n’est pas lisible ou bien position- ner comme montré, la couverture n’est pas bien positionnée. Avertissement : de sérieuses blessures peuvent arriver si la couverture est installée alors que l’abri n’est pas ancré.
Need help?
Do you have a question about the 78431 and is the answer not in the manual?
Questions and answers