Subscribe to Our Youtube Channel
Related Manuals for RKI Instruments 65-2336RK
Summary of Contents for RKI Instruments 65-2336RK
- Page 1 Part Number: 71-0178RK Revision: B Released: 7/6/20 1.800.544.2843 www.calcert.com sales@calcert.com...
- Page 2 WARNING 1.800.544.2843 www.calcert.com sales@calcert.com...
- Page 3 OBLIGATIONS OR LIABILITIES ON THE PART OF RKI INSTRUMENTS, INC. INCLUDING BUT NOT LIMITED TO, THE WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. IN NO EVENT SHALL RKI INSTRUMENTS, INC., BE LIABLE FOR INDIRECT, INCIDENTAL, OR CONSEQUENTIAL LOSS OR DAMAGE OF ANY KIND CONNECTED WITH THE USE OF ITS PRODUCTS OR FAILURE OF ITS PRODUCTS TO FUNCTION OR OPERATE PROPERLY.
- Page 4 Overview ..............5 Specifications.
- Page 5 WARNING: Do not use this product in a manner not specified in this instruction manual. WARNING: When using the 65-2336RK, you must follow the instructions and warnings in this manual to assure proper and safe operation of the 65-2336RK and to minimize the risk of personal injury.
- Page 6 Controller Terminal Strip Factory Adjust Pot Span Pot Zero Pot Amplifier + Test Point (Red) Detector Terminal Strip - Test Point (Black) J-Box CO Detector 1.800.544.2843 www.calcert.com sales@calcert.com...
- Page 7 Detector Housing Body Cap Gasket Plug-In CO Sensor Rubber Boot With Charcoal Filter Detector Housing Cap Flame Arrestor Guard Detector Housing Body Housing Cap & Cap Gasket Plug-In CO Sensor 1.800.544.2843 www.calcert.com sales@calcert.com...
- Page 8 Charcoal Filter Controller Terminal Strip Detector Terminal Strip Zero Pot Span Pot CAUTION: The amplifier includes an additional pot. It is factory-set. Do not adjust it. Test Points 1.800.544.2843 www.calcert.com sales@calcert.com...
- Page 9 1.800.544.2843 www.calcert.com sales@calcert.com...
- Page 10 3.10 3/4 NPT Female 3.65 Rubber Spacers 8.45 Max J-Box CO Detector 1 1/2-20 Thread for Calibration Cup 1.800.544.2843 www.calcert.com sales@calcert.com...
- Page 11 WARNING: If the controller’s construction is not explosion-proof, the controller must be installed in an ordinary location. Do non install a non-explosion-proof controller in a classified location. WARNING: To maintain the explosion proof classification of the CO detector/junction box combination, a conduit seal must be used within 2 inches of the junction box conduit hub used for wiring to the controller.
- Page 12 Install conduit seal Controller Detec tor/T ransmitter within 2 inches Terminals, T ypic al D esignations Cable Shield Controller Housing (installed in ordinary location if device is non-explosion-proof) J-Box Black CO Detector 1.800.544.2843 www.calcert.com sales@calcert.com...
- Page 13 CAUTION: Allow the transmitter to warm up for 5 minutes before you continue with the next section, “Setting the Zero Signal”. WARNING: Do not remove the detector housing cap or junction box cover while the circuits are energized unless the area is determined to be non-hazardous. Keep the detector housing cap and junction box cover tightly closed during operation.
- Page 14 Daily Quarterly 1.800.544.2843 www.calcert.com sales@calcert.com...
- Page 15 Note: Under “normal” circumstances, the transmitter requires calibration once every 3 months. Some applications may require a more frequent calibration schedule. 1.800.544.2843 www.calcert.com sales@calcert.com...
- Page 16 Replacing the Plug-In CO sensor CAUTION: The sensor contains electrolyte which is a dilute acid. Do not disassemble the sensor when replacing it with a new one. If sensor electrolyte comes in contact with your skin, wash affected area thoroughly with soap and water. WARNING: The CO sensor will not operate properly if the wire jumper is not removed.
- Page 17 Replacing the Charcoal Filter Replacing the CO Detector 1.800.544.2843 www.calcert.com sales@calcert.com...
- Page 18 CAUTION: Allow the replacement detector to warm up for 5 minutes before you continue with the next step. Replacing the Amplifier 1.800.544.2843 www.calcert.com sales@calcert.com...
- Page 19 WARNING: Do not remove the detector housing cap or junction box cover while the circuits are energized unless the area is determined to be non-hazardous. Keep the detector housing cap and junction box cover tightly closed during operation. Output (mV) = (calibrating sample/fullscale) X 400 + 100 167 (mV) = (50/300) X 400 +100 1.800.544.2843 www.calcert.com...
- Page 20 1.800.544.2843 www.calcert.com sales@calcert.com...
- Page 21 1.800.544.2843 www.calcert.com sales@calcert.com...
Need help?
Do you have a question about the 65-2336RK and is the answer not in the manual?
Questions and answers