Subscribe to Our Youtube Channel
Related Manuals for Hameg HO730
Summary of Contents for Hameg HO730
- Page 1 E T H E R N E T / U S B - I N T E R F A C E H O 7 3 0 Installation guidelines English...
-
Page 2: Declaration Of Conformity
General information regarding the CE marking HAMEG instruments fulfi ll the regulations of the EMC directive. The conformity test made by HAMEG is based on the actual generic- and product standards. In cases where different limit values are applicable, HAMEG applies the severer standard. For emission the limits for KONFORMITÄTSERKLÄRUNG... -
Page 3: Table Of Contents
3.1 Ethernet 3.2 USB 4. Oscilloscope Firmware 5. Interface Fitting Instruction 5.1 Removing the existing interface 5.2 Fitting the interface HO730 6. Interface Selection 7. USB-Driver Installation 7.1 Installation under Windows XP: 8. Ethernet confi guration 8.1 IP networks (IP – Internet protocol) 8.2 Ethernet interface parameters at the oscilloscope 10... -
Page 4: Safety Hints
> Firmware_HMxxx_Vxxx.zip. HO730 is a DUAL Interface that can be used either as an Ether- net or as a USB 2.0 / 1.1 Interface. It is used with the HAMEG After receiving the current fi rmware and its installation instruc- CombiScopes HM1008 and HM1508 for data transfer and tion, the fi... -
Page 5: Interface Fitting Instruction
F i t t i n g o f t h e H O 7 3 0 5.2 Fitting the interface HO730 5. Interface Fitting Instruction Safety! The following procedures must only be carried out on condition that the mains (line) power cable is not connected to the oscilloscope and no connection is made at the measurement inputs. -
Page 6: Interface Selection
I n t e r f a c e s e l e c t i o n 6. Interface Selection 6.1.2 USB USB is selected when highlighted. Further settings are not required. 6.1 Interface Selection Press the SETTINGS pushbutton to call the “Settings” menu. The function key “Interface”... -
Page 7: Usb-Driver Installation
7.1 Installation under Windows XP: 7.1.3.1 If the driver software has not been found, the message „The wizard could not fi nd the software for ... ? HAMEG HO730” is displayed. Please click “Back” until item 7.1.2 is displayed. 7.1.1 Please choose “No, not this time” and click “Next”. - Page 8 7.1.3.4 After the selected path is displayed click “Next”. 7.1.4 Thereafter the “Hardware Installation” window is displa- yed, showing a warning to continue the installation procedure. As this warning is irrelevant in case of HO730 driver software, click „Continue Anyway“. Änderungen vorbehalten...
-
Page 9: Ethernet Confi Guration
E t h e r n e t c o n f i g u r a t i o n Apart from the organization of IP addresses into public and pri- 8. Ethernet confi guration vate address ranges, IP addresses are also divided into classes (Class: A, B, C, D, E). - Page 10 I n s t a l l i n g t h e U S B - D r i v e r here without much mathematical expenditure to determine and it can with these subnet mask up to 254 network elements (e.g. measuring instruments, hosts/PC‘s...) in a network be operated at the same time.
-
Page 11: Ethernet Interface Parameters At The Host (Pc)
E t h e r n e t c o n f i g u r a t i o n 8.3 Ethernet interface parameters at the host (PC) 8.3.1 Parameters under Windows XP Reference! In order to be able to accomplish the following parameters, you have to be announced at the host concerned (PC) as “administrator“, or you have to be member of the user group “administrators“... -
Page 12: Test Of The Connection To The Oscilloscope
LAN-/WAN networks among themselves with switches and/or routers (e.g. over the Internet) connected. The interface HO730 has also a Web server, which can be used with a Web browser (e.g. Internet Explorer, …). The following func- tions are supported by the Web server (only in digital mode): It opens an input window. - Page 13 If the present HMLab version is below 1.0 the current version can be found in the Internet (www.hameg.com) for downloading and updating your PC. The path of the software is: Products > Oscilloscopes > (oscilloscope type) > Software/Firmware (below the oscilloscope picture) >...
- Page 14 Subject to change without notice...
- Page 15 A p p l i c a t i o n Änderungen vorbehalten...
- Page 16 . h a m e g . d e Subject to change without notice 29-09-2006-gw HAMEG Instruments GmbH © HAMEG Instruments GmbH Industriestraße 6 A Rohde & Schwarz Company D-63533 Mainhausen ® registered trademark Tel +49 (0) 61 82 800-0 DQS-Certifi...
Need help?
Do you have a question about the HO730 and is the answer not in the manual?
Questions and answers