4. 4. Make sure any
Make sure any tears or burrs on the
Adjus
Adjust
t
m
m
e
e
nt
nt
E
E
p
p
s
s
o
o
n
n
E
E
T
T
-
-
4
4
5
5
5
5
0
0
,
,
L
L
6
6
3.3.1.2
3.3.
1.2 Conf
Confirma
When performing the PG adjustment, make sure of the following.
When performing the PG adjustment, make sure of the
1. 1. Mov
Move the C
e the CR Uni
2. 2. Place the 1
Place the 1.48 mm thi
80-digit side
80-digit side
Make sure to wear the
Make sure to wear the heavy gloves to prevent the
trimming the Teflon tape.
trimming the Teflon tape.
tears or burrs on the applied Teflon ta
5
5
5
5
/
/
6
6
5
5
6
6
irmation
tion proc
procedur
edure e
Make sure the parts assembled on the CR Unit are as follows.
Make sure the parts assembled on the CR
Pa
Part rt(
(
s)
s)
to
to
be
be
as
ass
s
em
embl bled
• • E E m m p p t t y y A A d d a a p p t t e e r r s s
Note "*":
Note
"*":
Not necessarily removed from the printer if the part(s) is/are not assembled
Not necessarily removed from the printer if the part(s) is/are not assembled on the CR Unit.
Move the CR Unit by pulling the top of the CR timing belt.
Move the CR Unit by pulling the top of the CR timing belt.
Be careful not to damage the nozzle surface of the
Be careful not to
damage the nozzle surface of the Printhead with the thickness gauge.
When make the Printhead touch the thickness gauge, be careful not to let
When make the Printhead touch the thickness gauge, be careful
run onto the gauge.
run onto the gauge.
R Unit in th
t in the mid
e middle o
dle of the p
f the prin
.48 mm thicknes
ckness gauges p
s gauges protect
Thickness gauges
Thickness gauges
heavy gloves to prevent the cutter from cutting the hand when
applied Teflon tape, then the modific
pe, then the modification of thickness gau
D
D
e
e
t
t
a
a
ils
ils
o
o
f
f Ad
Adjust
justm
m
e
e
nt nts
Unit are as follows.
ed
on
on
the C
th
e
CR U
R
Uni nit
t
:
:
• • C C R R S S c c a a l l e e
• • Ad
Adap
• • Tu
Tube G
• • Ink S
Ink Suppl
rinter
ter. .
rotected with Te
ed with Teflon tap
flon tape on the poin
cutter from cutting the hand when
ation of thickness gauges is complete.
s
following.
Pa
Part rt(s (s) N
)
NOT
OT
to
to
be
be
asse sem
as
m
bl bled
ed
apte ter Co
r Cove
ver r
be Gui uide S
de She
heet et* *
upply Ada
y Adapte
pter Tub
r Tube Ass
e Assy*
y*
on the CR Unit.
Printhead with the thickness gauge.
not to let the Printhead
e on the points shown be
ts shown below.
low.
Thickness gauges
Thickness gauges
ges is complete.
63
63
Confidential
Confidential
R
R
e
e
v
v
i
i
s
s
i
i
o
o
n
n
B
B
on
on
th
the C
e
CR U
R
Uni nit
t
the Printhead
0-digit side
0-digit side