Page 1
(Model BM06 - Elec) 2kw Electric Heater Fire User / Installation instructions These instructions should be read carefully and retained for future reference.
CONTENT Important Notes………………………………………………………………………………..…..3 Technical Specification……………………………………………………………………….….4 Parts List……………………………………………………………………………………….…..…..5 Fire Installation…………………………..………………………………………………….………6 - 7 Operation by Manual Control…………………………………………………………………8 Operation by Remote Control…………………………………………………………………9 - 16 Electric Fire Guarantee…………………………………………………………………………..17...
IMPORTANT NOTES For indoor use only This appliance is not suitable for use outside the house and only suitable for well insulated spaces or occasional use. This heater must not be located immediately below a fixed socket outlet. Do not use the heater in the immediate surrounds of a bath, a shower, or a swimming pool.
Page 4
This appliance can be used by children aged from 8 years and above and persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning use of the appliance in a safe way and understand the hazards involved.
PART LIST Please unpack carefully ensuring that any loose parts and all packing items are removed. Read any warning labels carefully (see Maintenance Section). Place waste packaging back into box and dispose of RESPONSIBLY 1.Screws 4pcs 2.Instruction Manual 3.Remote Control 4.AAA battery 2pcs...
FIRE INSTALLATION (unit: mm) Before You Start ● The appliance Data Plate is located Underneath the Heater box–Disconnect from the mains supply before removing the Glass as described in the maintenance section. ● Required for installation:4 off screws and plugs suitable for the wall media (Not supplied).
Page 8
● Offer the fire into the opening, swinging in the appliance as shown. ● Mark on the wall the positions of the fixing points on the side flanges of the fire. ● Remove the fire from the opening. ● Drill and plug the wall holes using suitable fixings. ●...
OPERATION BY MANUAL BUTTON MAIN POWER (ON / OFF) SWITCH: The main switch is on the bottom front of product, and it supplies power to all of the functions of the fireplace. This switch must be in the “ON” position for any of the functions including the remote to work. FLAME SETTING BUTTON: By pressing the FLAME button, the unit will cycle through four flame effect settings (high, medium, low and off) HEATER RUNNING INDICTOR: If the appliances heater is on and the flame and mood light...
OPERATION BY REMOTE CONTROL NOTE: This is thermostatic remote control. The remote should be in the same room as fireplace and placed on a flat surface. It must be placed away from the fire to prevent the hot air affecting the thermostatic reading. The communication frequency between the fire and remote has already been set up.
Page 11
Remote Handset in Standby R1 The screen shown to the right is when the remote handset is in standby mode. Before Day / Time set up Turn on / off R2 Press button to turn on the flame effect or turn off flame effect and heater when in normal mode After Day / Time set...
Page 12
Count Down Timer NOTE: This setting is only for normal mode. It allows the appliance to go into standby after a set period of time. R10 Press to cycle through the settings from Off and 0.5 hours to 9 hours. The timer logo and time will show on the screen.
Page 13
R16 Hold the arrow symbol button for 6 seconds to enter the daily timer setting. Max 3 timed heating periods per day. Press ‘←’ or ‘→’ to choose hour or minute, press ‘+’ or ‘-’ to set the time. Minute will increase / decrease by 15 minutes per press. Hold for 3 seconds or wait for 10 seconds to save and exit the heating time period setting.
Page 14
R21 Press until shows at the upper right corner of the screen, then enter the week timer heating mode. R22 Hold button for 6 seconds to enter the weekly timer setting Press ‘←’ or ‘→’ to move the cursor (a flashing underline), press the button in the corresponding week position to select (the character is highlighted) or...
Page 15
Adaptive Start Control R28 According to room temperature and set temperature, the heater will automatically come on in time to heat the room to the set temperature at the set time. For example, if your timer is set to start at 18:00 and temperature is set to 23°C, the fire will come on at 17:30 to ensure the room is 23°C at 18:00.
Page 16
Resetting the Thermal Cut Out R33 The appliance is fitted with an Electronic Safety Control (E.S.). This is a safety device, which switches off the fire if, for any reason, the appliance overheats, e.g. when covered. If the heater stops operating while the flame effect continues working normally, this indicates that the E.S.
Page 17
Maintenance: WARNING: - Before undertaking any maintenance or cleaning, ensure appliance is disconnected from mains supply. Only competent persons should service / repair appliance. WARNING: There are no internal user serviceable parts, i.e. bulbs, in this product. Under no circumstance should access be gained to the internal parts other than by a suitably qualified person.
Electric Fire Guarantee Be Modern Group (the ‘Company’) provide a twelve month guarantee in respect of this electric fire appliance. 1. The twelve month Guarantee applies to: ● All ‘Products’ in the ranges manufactured by the ‘Company’ (but subject to exceptions below);...
Need help?
Do you have a question about the BM06 Elec and is the answer not in the manual?
Questions and answers