Technical Data; Led Indicators; Care And Cleaning - Renkforce 1697436 Operating Instructions Manual

a) Power Supply
- Both sources of power are independent and provide reverse-polarity voltage protection.
If both are connected at the same time, the source with the highest voltage will be used.
- Only requires one source of power is required and the power supply is designed to be
redundant. If two sources of power are connected and one fails, the unit will immediately
switch to the alternative power source.
Requirements
• The device only requires one source of power to operate, and the power supply is designed
to be redundant. If two sources of power are connected and one fails, the unit will immediately
switch to the alternative power source.
• Both sources of power are independent and provide reverse-polarity voltage protection. If
both are connected at the same time, the one with the highest voltage will be used.
• The terminal block requires a stabilized 5-60 V/DC input. See 'Technical data' for requirements.
Terminal Block
PW1 PW2
• Check the LED PW1 / PW2 (7) on the front panel to make sure that the powered switches
are receiving power.
Grounding Connection
• The grounding connection (2)
is available for connecting to an electrical grounding.
• Connect it to the electrical grounding of the control cabinet where the network switch is
installed.
b) Place on DIN Rail
• The DIN rail has to comply with EN 55022 (overall width 3.5 cm, overall height 0.75 cm). The
product may not be installed on any other mounting rails!
• Place the product on the DIN rail and secure it in place.
c) Network Cable Connection
• Use suitable network cables to connect devices and computers to the switch ports.
• All network ports supports auto uplink, which means that no crosslink cables are necessary
to connect multiple network switches.
• Make sure the cables are not bent or crushed.
• We recommend to mark the network cables with suitable adhesive labels or other devices.
This will allow you in case of a fault to know perfectly which connections need to be checked.

LED Indicators

LED Colour Status
PW1 Amber ON
Amber OFF
PW2
Amber ON
Amber OFF
Link/Act Green ON
Green OFF
Green Flashing
Speed Amber ON
Amber Flashing

Care and Cleaning

• Disconnect the product from the mains before each cleaning.
• Do not use any aggressive cleaning agents, rubbing alcohol or other chemical solutions as
they can cause damage to the housing and malfunctioning.
• Clean the product with a dry, fibre-free cloth.
• Connect the 6-pin terminal block to the terminal input
(3).
• Connect one end of the terminal power supply leads
(not included) to PW1 or PW2 on the terminal block,
and connect the other end to the power supply.
• The power leads should be wired to the 6-pin power
terminal block matching polarities as marked.
Description
Receiving power
No power received
Receiving power
No power received
Link active
Link inactive
Network activity
Port is operating at 1000 Mbit/s
Port is operating at 10/100 Mbit/s
Disposal
Electronic devices are recyclable waste and must not be disposed of in the
household waste. At the end of its service life, dispose of the product in accordance
with applicable regulatory guidelines.
You thus fulfill your statutory obligations and contribute to the protection of the environment.

Technical Data

Input Power .................................. 12 - 48 V/DC max. 60 V/DC
Operating Current ......................... 12 V/DC 0.86 A - 48 V/DC 0.25 A
Number of ports ............................ 16 x RJ45
Power consumption ...................... max. 10 W
Switching capacity ........................ 32 Gbps
Forwarding rate ............................ 23.8 Mpps
MAC address ................................ 8 K
Buffer memory .............................. 4.1 Mb
Media device interface .................. Auto-MDI/MDI-X, auto-negotiation, non-blocking
Standards ..................................... IEEE 802.3 10BaseT, IEEE 802.3u 100BaseTX,
IEEE 802.3ab 1000BaseT, IEEE 802.3az Energy Efficient,
Ethernet (EEE), Carrier Sense Multiple Access with
Collision Detection (CSMA/CD)
EMI ............................................... FCC Class A Part 15
EMS .............................................. EN61000-4-2, EN61000-4-3
IEC ................................................ IEC60068-2-27 (shock), IEC60068-2-31 (freefall),
IEC60068-2-6 (vibration)
Filtering / forwarding rates ............ 1000Mbps – 1,488,000pps 100Mbps – 148,800pps
10Mbps – 14,880pp
Transmission media...................... 10BaseT Cat. 3, 4, 5 UTP/STP, 100BaseTX Cat. 5 UTP/
STP, 1000BaseT Cat., 5E UTP/STP
Transmission method ................... Store and forward
LED indicators .............................. Port: Link/Act (green), connection speed (green)
Unit: Power (Amber)
Ingress protection rating ............... IP30 (housing only)
Mounting ....................................... DIN rail
Operating temperature ................. -40 to +75 °C, 5 – 95 % RH (non-condensing)
Storage temperature ..................... -40 to +75 °C, 5 – 95 % RH (non-condensing)
Dimensions (H x W x D) ............... 45 x 136 x 104 mm
Weight .......................................... 339 g
This is a publication by Conrad Electronic SE, Klaus-Conrad-Str. 1, D-92240 Hirschau (www.conrad.com). All rights
including translation reserved. Reproduction by any method, e.g. photocopy, microfilming, or the capture in electronic data
processing systems require the prior written approval by the editor. Reprinting, also in part, is prohibited. This publication
represents the technical status at the time of printing.
Copyright 2018 by Conrad Electronic SE. *1697436_v1_0818_02_dh_m(2)_en