AEG MC 4416 CD/MP3 Instruction Manual & Guarantee page 14

English
14
22 FUNCTION Function selector button
23 BAND button
24 IR Sensor for the remote control
25 button (Standby/On)
Reverse Side (not shown)
26 FM ANT. throw-out aerial
27 SPEAKERS R/L Loudspeaker connections
28 HEADPHONES Headphones connection
29 Mains connection
Remote Control
1 STANDBY button
2 MUTE (sound off ) button
3 TIMER button
4 /II button (Play/Pause)
5 I button (forward search)
6 ST/MO/ID3 button
7 VOLUME UP/DN (volume) buttons
8 DBBS button
9 Number buttons
10 SLEEP button
11 EQ button
12 FOLDER UP/DN buttons
(up / down album/Radio memory preset)
13 PLAY MODE button (repeat/random)
14 /PAIRING button
15 I button (reverse search)
16 / button
17 FUNCTION Function selector button
18 MEMORY/CLOCK button (memory/time)
19 BAND button
Intended Use
This device is used for:
• The reception of radio programmes
• Playing back/recording audio cassettes
• Playing back audio/MP3 CDs
• Playing back fi les via Bluetooth
• Telephoning using a hands-free kit via Bluetooth.
It is intended exclusively for this purpose and may only
be used as such. It may only be used in the manner
described in these instructions for use. The device must
not be used for commercial purposes.
Any other use of this device is considered to be contrary
to the intended use and may result in damage to materi-
als or even personal injury.
The fi rm ETV – Elektro-Technische Vertriebsgesellschaft
mbH does not accept any liability for damage caused as
a result of the use of this device contrary to its intended
use.
Start-up of the device/Introduction
• Read the operating instructions thoroughly before the
start-up!
05-MC 4416CD_MP3 AEG.indd 14 05-MC 4416CD_MP3 AEG.indd 14
• Select an appropriate location for the device, e.g. a
dry, fl at, non-slip surface on which the device can be
easily operated.
• Make sure that the device is adequately ventilated!
• Connect the loudspeakers to the back of the music
centre to the sockets market „Speaker R and L" (27).
• Remove the protective fi lm from the display if it is
still present.
Power Supply
• Insert the plug into a properly installed 230 V, 50 Hz
power socket.
• Please ensure that the mains voltage corresponds to
the information on the type plate.
• The stored time and stations are lost as soon as the
power supply is interrupted.
Setting the Time (in Standby Mode)
1. Press the MEMORY/CLOCK button (3/18 on the remo-
12
te control). The words „
2. Use the I/I buttons (18/5/15)
between the 24 hour and 12 hour display. Press the
MEMORY/CLOCK button to confi rm.
NOTE:
The following appears in the case of the 12 hour
display
AM = in the morning,
PM = in the afternoon/evening.
3. Press the I/I buttons
the MEMORY/CLOCK button to confi rm.
4. Press the I/I buttons
minutes.
5. Press the MEMORY/CLOCK button again to store the time.
Remote Control Batteries (not supplied)
• Open the lid of the battery compartment on the back
of the remote control.
• Insert 2 batteries of type R03 „AAA" 1,5 V. Ensure
that the polarity is correct (see the fl oor of the batte-
ry compartment)!
• If the remote control is not used for a prolonged pe-
riod, remove the batteries in order to prevent battery
acid leaking.
CAUTION:
• Diff erent battery types or new and used batteries
must not be used together.
• Batteries are not to be disposed of together with
domestic wastes. Dispose of the used batteries at
the relevant collection bin or at your dealer's.
WARNING:
Do not expose the batteries to high temperatures or
direct sunlight. Never throw batteries into the fi re.
There is a danger of explosion!
HR" appear in the display.
to choose
to set the hours. Press
in order to set the
12.02.2008 10:15:40 Uhr 12.02.2008 10:15:40 Uhr