Chamberlain Clicker KLIK1U User Manual

CLICKER
®
Universal Garage Door Opener Remote Control
Read instructions thoroughly BEFORE beginning.
Start with garage door closed. Identify garage door opener type -Smart/Learn
button or DIP Switch. Smart/Learn button or DIP Switches are located on motor
unit or external receiver. Refer to owner's manual if necessary.
STOP
Clicker products are intended to be used only with garage door openers
manufactured after 1993 that utilize photo-eyes safety sensors. These are
always located on or near the bottom of the door track. If your garage door
does not have the sensors attached and working, the opener is not
compliant with current federal safety regulations and should be replaced.
Proceed with instructions according to your type of garage door opener.
SMART/LEARN BUTTON
1
See Chart A to
determine # of times to
press button and write
in blank on step 5.
2
3
Press program button until
LED lights.
4
1 2 3
KG
KG
Motor Unit
Press and release the
smart/learn button.
5
Select a button to program.
Press button times
ensuring LED stops
flashing after each press.
Code is accepted when
one of the following
occurs:
Click
OR
NOTE: If there are
problems programming to
button 1, program to
button 2.
6
Press program button.
7
Programming complete.
Press selected button to
test. If unit does not work,
return to Step 3.
www.clickerproducts.com
1-800-442-1255
Chamberlain, LiftMaster and Moore-O-Matic are Trademarks of Chamberlain Group. Genie
is a Trademark of Overhead Door Corporation. Overhead Door is a Trademark of Overhead
Door Corporation. Linear is a Trademark of Linear Corporation. Master Mechanic is a
Trademark of TruServ. Sears is a Trademark of Sears & Roebuck. Stanley is a Trademark
of The Stanley Works. Wayne Dalton is a trademark of Wayne Dalton Corporation. Do It is
a trademark of Do It Best Corporation.
114A3485C
MODEL KLIK1U
CHART A
# of Brand Type/Color of
times to Smart/Learn
press
button
1 Linear ® Mega-Code
2 Chamberlain * Orange/Red
®
3 Chamberlain ® * Purple
4 Chamberlain ® * Green
5 Genie ®
Overhead Door ® Intellicode
6 Genie
®
Overhead Door ® Intellicode
7 Stanley ® Secure Code
9 Wayne Dalton ® Rolling Code
11 Chamberlain ® * 9 Position
*NOTE: LiftMaster, Do-It, Master Mechanic, Raynor, True Value and Sears Craftsman are compatible
with Chamberlain technology.
SMART/LEARN BUTTON
1 2
NOTE: Your opener may
appear different and you
may have to remove the
light lens to access the
learn button.
LED Indicator
Button 1
Program Button
OR
Battery
REMOTE CONTROL BATTERY
To prevent possible SERIOUS INJURY or DEATH:
• NEVER allow small children near batteries.
• If battery is swallowed, immediately notify doctor.
To reduce risk of fire, explosion or chemical burn:
• Replace ONLY with 3V2032 coin batteries.
• Do NOT recharge, disassemble, heat above 100°C (212°F) or
incinerate.
Dispose of batteries properly. Replace ONLY with 3V2032
coin batteries.
NOTICE: To comply with FCC and or Industry Canada (IC) rules, adjustment or modifications of this
receiver and/or transmitter are prohibited, except for changing the code setting or replacing the battery.
THERE ARE NO OTHER USER SERVICEABLE PARTS.
Tested to Comply with FCC Standards FOR HOME OR OFFICE USE. Operation is subject to the following
two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any
interference received, including interference that may cause undesired operation.
To prevent possible SERIOUS INJURY or DEATH from a moving gate or garage door:
• ALWAYS keep remote controls out of reach of children. NEVER permit children to
operate, or play with remote control transmitters.
• Activate gate or door ONLY when it can be seen clearly, is properly adjusted and
there are no obstructions to door travel.
• ALWAYS keep gate or garage door in sight until completely closed. NEVER permit
anyone to cross path of moving gate or door.
# of Brand
Year
times to
press
button
11 Chamberlain
'97-Current
12 Chamberlain
'97-'03
'95-'Current
13 Genie ®
'93-'96
14 Linear Multicode
15 Chamberlain
'95-'05
16 Stanley/Multicode
17 Genie
®
'05 Current
18 Linear ®
'98
Moore-O-Matic
'99
19 Chamberlain
'90-'92
OR
DIP SWITCH
ON
3
KG KG
Button 2
DIP Switches
Battery Cover
© 2008, Clicker Corporation
All Rights Reserved
CHART B
Description Year
® * 9 Position '90-'92
® * 9 Position
Canada '83-'89
12 Position '85
10 Position '76
®
® 8 Position '83-'89
® 10 Position '76
9 Position '85
® 8 Position '76
® * 7 Position '83-'89
NOTE:
2 Position DIP
Switch:
If programming fails reverse
DIP switches (OFF to ON and
ON to OFF).
**3 Position DIP Switch:
For Chamberlain remotes DO NOT
use the "0" position, use "+" or "-".
If you already have a 3-button
remote, DIP switch #1 must be set to
"-" if the large button is to open the door. It may be
necessary to reprogram original remote controls.
DIP SWITCH
1
See Chart B to
determine # of times to
press button and write
in blank on step 5.
2
3
Motor
Unit
Existing Remote
Clicker Remote
Match DIP switches. Turn
extra switches OFF.**
4
Press program button
until LED lights.
5
Select a button to program.
Press button times
ensuring LED stops
flashing after each press.
Code is accepted when
door activates.
6
Press program button.
7
Programming complete.
Press selected button to
test. If unit does not work,
return to Step 3.
ON