Perenio PECSS01 Installation And Operation Manual
Smoke sensor
Hide thumbs
Also See for PECSS01:
- Installation and operation manual (30 pages) ,
- Quick start manual (25 pages) ,
- Manual (8 pages)
Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Perenio PECSS01
Summary of Contents for Perenio PECSS01
- Page 1 Installation and Operation Manual for Perenio® PECSS01 Smoke Sensor July, 2021...
-
Page 3: Introduction
Copyright of ©Perenio IoT spol s r.o. All rights reserved. The Perenio® trademark is owned by Perenio IoT spol s r.o. (hereinafter referred to as the Perenio IoT). All other similar trademarks and names, as well as logos and other symbols are the property of their respective owners*. -
Page 4: Responsibility And Technical Support
Perenio IoT reserves the right to modify the device and make corrections or changes to this document without prior notice of the User, and shall not be responsible for any... -
Page 5: Conformance To Standards
To protect the environment and human health, please dispose of used electrical and electronic equipment according to approved safe disposal guidelines ©Perenio IoT spol s r.o. All Rights Reserved Doc Version: 2.5.1 Page 5 of 33... - Page 6 Details on available Certificates are specified in Section 6 of the present document. For copies of Certificates and Reports, please visit a corresponding Section at perenio.com. Doc Version: 2.5.1 ©Perenio IoT spol s r.o. All Rights Reserved Page 6 of 33...
-
Page 7: Table Of Contents
1.3 Scope of Delivery..................13 1.4 Packaging and Labelling ................13 1.5 Safe Operation Rules ................14 1.6 Standalone Operation of Perenio® Sensors ..........14 2 Installation and Setup................... 15 2.1 First Installation and Configuration ............16 2.2 Sensor Control Panel ................21 2.2.1 Battery Level .................. - Page 8 Table 3 – Typical Errors and Troubleshooting Methods ......... 32 Connection to the Perenio Smart Mobile App A. SWITCHING ON AND INSTALLATION OF THE PECSS01 SMOKE SENSOR .... 16 B. LOGIN TO THE EXISTING USER ACCOUNT ............18 C. CONNECTION TO THE CONTROL GATEWAY/IOT ROUTER ......... 19 Doc Version: 2.5.1...
-
Page 9: General Description And Specifications
1.1 General Purpose The Perenio® PECSS01 Photoelectric Sensor is a Zigbee-based device intended to detect visible smoke particles (flameless stage). It is used as part of the Perenio Smart Building Management System and provides for timely alert in the event of smoke in the room. -
Page 10: Figure 2 - Buttons And Indicators
Smoke Sensor to be detected by the Control Gateway/IoT Router Siren A signaling device that emits sound in the case of smoke in the room Doc Version: 2.5.1 ©Perenio IoT spol s r.o. All Rights Reserved Page 10 of 33... -
Page 11: Technical Specification
Silicon Labs EM3586 (Zigbee IC) Communication Zigbee HA 1.2 (IEEE 802.15.4) Technology Operating Frequency 2.4GHz to 2.5GHz Connection Radius up to 40 meters (open area) Zigbee Antenna Type: Built-in ©Perenio IoT spol s r.o. All Rights Reserved Doc Version: 2.5.1 Page 11 of 33... - Page 12 Dimensions (L x W x H) 60mm x 60mm x 49.2mm Weight 49.7g (70.2g with accessories) Warranty Period 24 months Service Life 24 months Certification CE, EAC, RoHS, UA.TR Doc Version: 2.5.1 ©Perenio IoT spol s r.o. All Rights Reserved Page 12 of 33...
-
Page 13: Scope Of Delivery
* Images of accessories are provided for informational purposes only 1.4 Packaging and Labelling The Perenio® PECSS01 Smoke Sensor is supplied in an individual blister package of 171mm x 126mm x 57mm (L x W x H) containing the full name and marking of the device, the list of accessories provided and basic technical specifications thereof, as well as the date of manufacture and information about the Manufacturer of devices. -
Page 14: Safe Operation Rules
PECSS01 Smoke Sensor 1.5 Safe Operation Rules For the proper and safe operation of Perenio® Sensors, follow the instructions and safety procedures described in the present Manual. The Manufacturer shall not be liable for any damage caused as a result of improper operation of devices. -
Page 15: Installation And Setup
5. Attach the device in the place of installation using the 3M tape. The entire process of setting-up the Sensor can be divided into several key stages: Logging in to the User Account of the Perenio Smart Mobile App; ... -
Page 16: First Installation And Configuration
Perenio Smart Mobile App, it is necessary to perform the following steps: 1. Unpack the Sensor and power it on (See par. A below). 2. Login in to the Perenio Smart Building Management System User Account (See par. B below). -
Page 17: Figure 4 - Installation Of The Smoke Sensor On A Flat And Sloping Ceiling
Smoke Sensor. 5. Switch on the Smoke Sensor by removing the battery isolation strip. 6. Reassemble the Smoke Sensor and the mounted bracket. ©Perenio IoT spol s r.o. All Rights Reserved Doc Version: 2.5.1 Page 17 of 33... -
Page 18: Figure 6 - Disassembling The Mounting Bracket From The Smoke Sensor
To restore a forgotten password, use the e-mail address linked to your User Account, to which instructions on changing the password will be sent. Doc Version: 2.5.1 ©Perenio IoT spol s r.o. All Rights Reserved Page 18 of 33... - Page 19 (You should remove the sensor battery and insert it back into the casing). NOTE. eliminate connection failures, follow instructions specified on corresponding screens of the smartphone. ©Perenio IoT spol s r.o. All Rights Reserved Doc Version: 2.5.1 Page 19 of 33...
-
Page 20: Figure 7 - Add New Device (Sensor) Procedure
PECSS01 Smoke Sensor The entire process of the Sensor connection in the Mobile App is shown below. – Add new device (Sensor) procedure Figure 7 Doc Version: 2.5.1 ©Perenio IoT spol s r.o. All Rights Reserved Page 20 of 33... -
Page 21: Sensor Control Panel
2.2.2 Event History In this tab, the user can view the status of the sensor, as well as the time when the event occurred. ©Perenio IoT spol s r.o. All Rights Reserved Doc Version: 2.5.1 Page 21 of 33... -
Page 22: Additional Settings
Subscription Plan (It is 7 days for free Subscription). 2.2.3 Additional Settings After the Sensor is activated in the Perenio Smart app, the user can make the following settings remotely: Change or upload the device image for easier identification of the sensor in the list of connected devices;... -
Page 23: Changing The Room Or Location For The Sensor
CG/IoT Router is required) as follows: a. Login in to the Perenio Smart app and select the Location where the Sensor is activated; b. In the Devices tab, select the required Sensor from the list and click on icon (Settings);... -
Page 24: History And Push-Notifications
If the sensor is disconnected, it will disappear from the list of connected devices. 2.3 History and Push-Notifications All notifications and other messages including changes in the status of Perenio® devices are displayed in the “History” tab. The most important messages can be viewed online in the “... -
Page 25: Battery Replacement
Control Gateway firmware update, as well as notifications about low battery level of the sensor and changing the armed mode for the Location. Typical Events. Various Perenio IoT newsletters, as well as messages about triggering Door & Window/Motion sensor in the disarmed mode. -
Page 26: Maintenance And Repair
Repair mechanical damages to devices (in Service Centers). The Perenio® PECSS01 Smoke Sensor repairs shall be carried out in Service Centers, because casings will have to be opened in the case of any element failure. In the case of warranty repairs or replacement, the User shall provide the Seller with the sales receipt and the purchased device. -
Page 27: Warranty Obligations
The Manufacturer shall guarantee that all materials, components and assemblies of Perenio® devices are free from defects under normal operation within the warranty period. The limited warranty shall be applied to the first End Customer of Perenio® devices only and cannot be transferred to a subsequent customer. - Page 28 Perenio® PECSS01 Smoke Sensor LIMITATION OF LIABILITY Perenio® devices SHALL NOT BE SUBJECT TO a free warranty service in the case of identification of at least one of the following damages or defects: Any damage caused by force majeure, accidents, and willful or careless acts (omissions) of the Customer or third parties;...
- Page 29 ©Perenio IoT spol s r.o. All Rights Reserved Doc Version: 2.5.1 Page 29 of 33...
-
Page 30: Storage, Transportation And Disposal Of Devices
PECSS01 Smoke Sensor 5 Storage, Transportation and Disposal of Devices The Perenio® Smoke Sensor may be shipped by any kind of covered vehicles (by rail, or road or in sealed heated airplane compartments, etc.) in accordance with the requirements of current regulatory documents applicable to fragile goods sensitive to moisture. -
Page 31: Other Information
TUV Test report #50102219 001 as of September 29, Declarations, Reports 2017 (EN 15604:2005/AC:2008) Addresses of Service Centers are available at perenio.com in the “Support” Section. ©Perenio IoT spol s r.o. All Rights Reserved Doc Version: 2.5.1 Page 31 of 33... -
Page 32: Troubleshooting
The battery is Observe the polarity of the pressing the test improperly inserted battery in the sensor button Low battery level of Change the battery the sensor Doc Version: 2.5.1 ©Perenio IoT spol s r.o. All Rights Reserved Page 32 of 33... -
Page 33: Glossary
General term which means a building or a structure in which Perenio® Cameras, Control Gateways/IoT Routers and/or Sensors are installed Perenio Smart Software developed by Perenio IoT for remote control of wireless Cameras from smartphones Viewing Angle The area that falls into the field of viewing of the Sensor...