Perenio PECSS01 Installation And Operation Manual
Smoke sensor
Hide thumbs
Also See for PECSS01:
- Installation and operation manual (33 pages) ,
- Quick start manual (25 pages) ,
- Manual (8 pages)
Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Perenio PECSS01
Summary of Contents for Perenio PECSS01
- Page 1 Installation and Operation Manual for Perenio® PECSS01 Smoke Sensor August, 2019...
-
Page 3: Introduction
Copyright of ©Perenio IoT spol s r.o. All rights reserved. The Perenio® trademark is owned by Perenio IoT spol s r.o. (hereinafter referred to as the Perenio IoT). All other similar trademarks and names, as well as logos and other symbols are the property of their respective owners*. -
Page 4: Responsibility And Technical Support
Perenio IoT reserves the right to modify the device and make corrections or changes to this document without prior notice of the User, and shall not be responsible for any... -
Page 5: Conformance To Standards
Details on available Certificates are specified in Section 6 of the present document. For copies of Certificates and Reports, please visit a corresponding Section at perenio.com. ©Perenio IoT spol s r.o. All Rights Reserved Doc Version: 2.1.0 Page 5 of 30... -
Page 6: Table Of Contents
1.3 Scope of Delivery ................. 11 1.4 Packaging and Labelling ................ 12 1.5 Safe Operation Rules ................12 1.6 Standalone Operation of Perenio® Sensors ..........13 2 Installation and Setup ................14 2.1 First Installation and Configuration ............15 2.2 Changing the Room or Location for the Sensor ......... 19 2.3 History and Push-Notifications .............. - Page 7 Table 2 – Typical Errors and Troubleshooting Methods ........29 Connection to the Perenio Smart Mobile App A. SWITCHING ON AND INSTALLATION OF THE PECSS01 SMOKE SENSOR ....15 B. LOGIN TO THE EXISTING USER ACCOUNT ............17 C. CONNECTION OF THE SMOKE SENSOR TO THE CONTROL GATEWAY ....18 ©Perenio IoT spol s r.o.
-
Page 8: General Description And Specifications
1.1 General Purpose The Perenio® PECSS01 Photoelectric Sensor is a ZigBee-based device intended to detect visible smoke particles (flameless stage). It is used as part of the Perenio Smart Building Management System and provides for timely alert in the event of smoke in the room. -
Page 9: Figure 2 - Buttons And Indicators
Client or caused to their estates, personal property and/or other products, devices, personal data and privacy. ©Perenio IoT spol s r.o. All Rights Reserved Doc Version: 2.1.0 Page 9 of 30... -
Page 10: Technical Specification
1% to 95% (non-condensing) Storage Temperature -10°C to +50°C Storage Humidity 1% to 95% (non-condensing) On a flat surface (Screws, 3M Tape). Installation For indoor installation only. Doc Version: 2.1.0 ©Perenio IoT spol s r.o. All Rights Reserved Page 10 of 30... -
Page 11: Scope Of Delivery
24 months Certification CE, EAC, RoHS, UA.TR 1.3 Scope of Delivery The following items and accessories are supplied within the Perenio® PECSS01 Smoke Sensor package: 1. PECSS01 Smoke Sensor (1 pc.) 2. Battery (CR123A) (1 pc.) 3. Screws and dowels (1 set) 4. -
Page 12: Packaging And Labelling
PECSS01 Smoke Sensor 1.4 Packaging and Labelling The Perenio® PECSS01 Smoke Sensor is supplied in an individual blister package of 171 x 126 x 57 mm (L x W x H) containing the full name and marking of the device, the list of accessories provided and basic technical specifications thereof, as well as the date of manufacture and information about the Manufacturer of devices. -
Page 13: Standalone Operation Of Perenio® Sensors
PECSS01 Smoke Sensor 1.6 Standalone Operation of Perenio® Sensors The Control Gateway in not necessarily required for all Perenio® Sensors in order to alert Users on potentially dangerous situations. So, the Smoke Sensor can operate as a standalone device, i.e. when it detects smoke in a room, it will beep. -
Page 14: Installation And Setup
5. Attach the device in the place of installation using the 3M tape. The entire process of setting-up the Sensor can be divided into several key stages: Logging in to the User Account of the Perenio Smart Mobile App; ... -
Page 15: First Installation And Configuration
Mobile App, it is necessary to perform the following steps: 1. Unpack the Sensor and power it on (See par. A below). 2. Login in to the Perenio Smart Building Management System User Account (See par. B below). 3. Connect the Smoke Sensor to the Mobile App (See par. C below). -
Page 16: Figure 4 - Installation Of The Smoke Sensor On A Flat And Sloping Ceiling
Smoke Sensor. 5. Switch on the Smoke Sensor by removing the battery isolation strip. 6. Reassemble the Smoke Sensor and the mounted bracket. Doc Version: 2.1.0 ©Perenio IoT spol s r.o. All Rights Reserved Page 16 of 30... -
Page 17: B. Login To The Existing User Account
To restore a forgotten password, use the e-mail address linked to your User Account, to which instructions on changing the password will be sent. ©Perenio IoT spol s r.o. All Rights Reserved Doc Version: 2.1.0 Page 17 of 30... - Page 18 Control Gateways activated in the User Account). NOTE. The Control Gateway must be connected to the mains and the Internet, as well as activated in the Perenio Smart App. Start searching for Sensors; d. If the LED flashes slowly after the first power on of...
-
Page 19: Changing The Room Or Location For The Sensor
1. Change the room/location (The CG remains the same) as follows: a. Demount the Sensor and move it to another room; ©Perenio IoT spol s r.o. All Rights Reserved Doc Version: 2.1.0 Page 19 of 30... -
Page 20: History And Push-Notifications
Change the Room in Sensor settings in the User Account. 2. Change the room/location (Connection to another CG is required) as follows: a. Login in to the Perenio Smart app and select the Location where the Sensor is activated;... -
Page 21: Battery Replacement
Gateway firmware update process, as well as low battery notifications and changes of the Armed/Disarmed mode for the Location. Standard events. Various news and other information from Perenio IoT, as well as alerts from both the Door&Window Sensor and the Motion Sensor when in the Disarmed mode. -
Page 22: Maintenance And Repair
In the case of warranty repairs or replacement, the User shall provide the Seller with the sales receipt and the purchased device. For details on the replacement and repairs of the PECSS01 Smoke Sensor, please contact your local Company representative or the Tech Support Department at perenio.com. -
Page 23: Warranty Obligations
The Manufacturer shall guarantee that all materials, components and assemblies of Perenio® devices are free from defects under normal operation within the warranty period. The limited warranty shall be applied to the first End Customer of Perenio® devices only and cannot be transferred to a subsequent customer. - Page 24 Perenio® PECSS01 Smoke Sensor LIMITATION OF LIABILITY Perenio® devices SHALL NOT BE SUBJECT TO a free warranty service in the case of identification of at least one of the following damages or defects: Any damage caused by force majeure, accidents, and willful or careless acts (omissions) of the Customer or third parties;...
- Page 25 ©Perenio IoT spol s r.o. All Rights Reserved Doc Version: 2.1.0 Page 25 of 30...
-
Page 26: Storage, Transportation And Disposal Of Devices
PECSS01 Smoke Sensor 5 Storage, Transportation and Disposal of Devices The Perenio® PECSS01 Smoke Sensor may be shipped by any kind of covered vehicles (by rail, or road or in sealed heated airplane compartments, etc.) in accordance with the requirements of current regulatory documents applicable to fragile goods sensitive to moisture. -
Page 27: Other Information
ASBIS POLAND Sp. z o.o. Address Ul. Szyszkowa 43, 02-285 Warszawa Quality Claims Acceptance and Warranty Service Company Croatia Name ASBISc-CR d.o.o. Address Slavonska avenija 24/6, 10000 Zagreb, RH ©Perenio IoT spol s r.o. All Rights Reserved Doc Version: 2.1.0 Page 27 of 30... - Page 28 TUV Test report #50102219 001 as of September 29, Declarations, Reports 2017 (EN 15604:2005/AC:2008) Addresses of Service Centers are available at perenio.com in the ‘Support’ Section. Doc Version: 2.1.0 ©Perenio IoT spol s r.o. All Rights Reserved Page 28 of 30...
-
Page 29: Troubleshooting
PECSS01 Smoke Sensor 7 Troubleshooting Table 2 below shows typical errors and problems that may occur in the process of connection and configuration of the Perenio® PECSS01 Smoke Sensor . Table 2 – Typical Errors and Troubleshooting Methods Item Problem... -
Page 30: Glossary
General term which means a building or a structure in which Perenio® Cameras, Control Gateways and/or Sensors are installed Perenio Smart Software developed by Perenio IoT for remote control of wireless Cameras from smartphones Viewing Angle The area that falls into the field of viewing of the Sensor...