Related Manuals for Elby Designs MonoWave(X)
Summary of Contents for Elby Designs MonoWave(X)
- Page 1 MonoWave(X) Build Guide MonoWave(X) Construction Guide Version 1.3 PCB Revision V1,2 August 28 2021 ELBY Designs - Laurie Biddulph 3 Therese Street, Bridport, TAS 7262, Australia elby-designs@bigpond.com http://www.elby-designs.com 1 of 14...
- Page 2 Test Points (TPxxx) should be left clear. This will assist with ‘poking’ a test probe tip in to the test point and help prevent the probe from wandering. ELBY Designs - Laurie Biddulph 3 Therese Street, Bridport, TAS 7262, Australia elby-designs@bigpond.com...
- Page 3 Turn the assembly over and position the LEDs in to their respective mounts. Solder in to place. We recommend fitting the front panel to the enclosure BEFORE mounting the Panel PCB to allow easier access to the securing bolts. ELBY Designs - Laurie Biddulph 3 Therese Street, Bridport, TAS 7262, Australia elby-designs@bigpond.com http://www.elby-designs.com...
- Page 4 Side Panel or to the back of the slots, this will help protect connectors from being squashed and provide more clearance at the back of the unit. ELBY Designs - Laurie Biddulph 3 Therese Street, Bridport, TAS 7262, Australia elby-designs@bigpond.com...
- Page 5 Fit the Rear Panel component assemblies and plug on to their respective headers on the main board. The MonoWave(X) should now be calibrated after which the top and bottom covers can be fitted. ELBY Designs - Laurie Biddulph 3 Therese Street, Bridport, TAS 7262, Australia elby-designs@bigpond.com http://www.elby-designs.com...
- Page 6 MonoWave(X) Build Guide The complete MonoWave assembly (earlier version of parts are shown) ELBY Designs - Laurie Biddulph 3 Therese Street, Bridport, TAS 7262, Australia elby-designs@bigpond.com http://www.elby-designs.com 6 of 14...
- Page 7 Apply power and adjust P1301 for optimum contrast. MIDI-CV Module Trimmer Module Function P401 MIDI-CV V/Octave Scaling Monitor TP401 and adjust P401 for an output of -10.667V ELBY Designs - Laurie Biddulph 3 Therese Street, Bridport, TAS 7262, Australia elby-designs@bigpond.com http://www.elby-designs.com 7 of 14...
- Page 8 Play and hold a low MIDI Note (eg C2) Adjust P901 so that after the envelope has complete you can just hear the note ELBY Designs - Laurie Biddulph 3 Therese Street, Bridport, TAS 7262, Australia elby-designs@bigpond.com http://www.elby-designs.com...
- Page 9 MonoWave(X) Build Guide Front Panel Rear Panel Original Rear Panel Later Decal for Rear Panel Current Rear Panel ELBY Designs - Laurie Biddulph 3 Therese Street, Bridport, TAS 7262, Australia elby-designs@bigpond.com http://www.elby-designs.com 9 of 14...
- Page 10 MonoWave(X) Build Guide The MonoWave requires 15VDC 400mA power supply (please note the current rear panel incorrectly shows 18VDC) ELBY Designs - Laurie Biddulph 3 Therese Street, Bridport, TAS 7262, Australia elby-designs@bigpond.com http://www.elby-designs.com 10 of 14...
- Page 11 MonoWave(X) Build Guide Addendum ELBY Designs - Laurie Biddulph 3 Therese Street, Bridport, TAS 7262, Australia elby-designs@bigpond.com http://www.elby-designs.com 11 of 14...
- Page 12 Turn on A440 Adjust CUTOFF FREQUENCY for 1760Hz (2 octaves above A440) Adjust Filter Scale trim for zero beat at A220 ELBY Designs - Laurie Biddulph 3 Therese Street, Bridport, TAS 7262, Australia elby-designs@bigpond.com http://www.elby-designs.com 12 of 14...
- Page 13 MonoWave(X) Build Guide ELBY Designs - Laurie Biddulph 3 Therese Street, Bridport, TAS 7262, Australia elby-designs@bigpond.com http://www.elby-designs.com 13 of 14...
- Page 14 MonoWave(X) Build Guide ELBY Designs - Laurie Biddulph 3 Therese Street, Bridport, TAS 7262, Australia elby-designs@bigpond.com http://www.elby-designs.com 14 of 14...
Need help?
Do you have a question about the MonoWave(X) and is the answer not in the manual?
Questions and answers