Table of Contents
Advertisement
INDEX OF ILLUSTRATIONS
FIG. n°1
-
General view of the Vegetable cutter mod.TM
FIG. n°2
-
Electrical safety device
FIG. n°3
-
Mechanical safety device
FIG. n°3A
-
Electrical safety device
FIG. n°4
-
Position of the slide and tray to allow
for ignition
FIG. n°5
-
On-off card
FIG. n°6
-
Vegetable-pressing pestle
FIG. n°7
-
Tray with magnetic sensor
FIG. n°8
-
Product conveying slide
FIG. n°9
-
Expulsion palette
FIG. n°10
-
Disc shaft
FIG. n°11
-
Utensil "DF" type
FIG. n°12
-
Utensil "DT" type
FIG. n°13
-
Utensil "DQ" type
FIG. n°14
-
Utensil "PS" type
FIG. n°15
-
Dimension and maximum volume
FIG. n°16
-
Description of the packing
FIG. n°17
-
Collecting device and tray
FIG. n°18
-
Conveying device with slide
FIG. n°19
-
Technical-registration plate
FIG. n°20
-
Direction of disc rotation
FIG. n°21
-
Triphase electrical installation drawing
FIG. n°21A -
Monophase elecrtical installation drawing
FIG. n°22
-
On-off switch
FIG. n°23
-
Assembly of expulsion palette
FIG. n°24
-
Assembly of coupled discs PS-DF
FIG. n°25
-
Correct position
FIG. n°26
-
Product loaded at the mouth of the lid
FIG. n°27
-
Product loaded from the conductor on the lever pag.21
FIG. n°28
-
View of the machine dismantled for cleaning
pag. 6
pag. 8
pag. 8
pag. 8
pag. 9
pag. 9
pag.10
pag.10
pag.10
pag.10
pag.11
pag.11
pag.11
pag.12
pag.12
pag.13
pag.14
pag.16
pag.16
pag.17
pag.17
pag.18
pag.18
pag.19
pag.20
pag.20
pag.20
pag.21
pag.24
4
B Once all of the product inserted has been processed and by lifting the
thrusting lever, a safety mechanism will prevent the machine from
continued processing. Once more product has been loaded and the
lever has been lowered, the machine will automatically restart.
Fig. n°26 - Product loaded via opening
of the lid.
C Proceed as described in point 5.1 "A" for the replacement of discs and
thus change in processing. After this operation the electrical system
will prevent the machine from starting automatically; push the "l"
button to get it started again.
D If the collecting tray is used, empty its contents every 2-3 cycles. Use
of the machine when the tray is overfull may hinder the correct flow of
the cut product from the processing area, causing incorrect cutting,
jamming the machine or damage the motor.
CAP.6 - MAINTENANCE AND PRACTICAL ADVISE
6.1 - GENERAL REMARKS
Prior to performing any operation it is necessary to:
Remove the plug from the supply network in order to completely isolate
the machine from the rest of the installation
6.1.1 - BELT
There is no need to adjust the belt. It generally needs to be replaced after
3-4 years, in case of breakage call the "Assistance Centre".
6.1.2 - FEET
With time the feet may deteriorate and lose their elasticity, thus
diminishing the stability of the machine. See to their replacement if this is
the case.
Fig. n°27 - Product loaded via
conductor on the lever
21
Advertisement
Table of Contents
