Bayco 623 Instructions

Instructions for Model 623
15 Watt Fluorescent Work Light
INS-623-12
Electrical Rating - 125 Volts 60 Hz
CAUTION - TO REDUCE THE RISK OF ELECTRIC SHOCK AND FIRE - PULL PLUG
WHEN SERVICING, OR WHEN RE-LAMPING - USE ONLY 15 WATT BULB
CAUTION
DO NOT use in explosive atmospheres, near flammable liquids, or where explosion proof
lamps are required.
DO NOT use in the proximity of vehicles or equipment when there is a risk of flammable
liquids coming into contact with the hand lamp
DO NOT immerse in water
DO NOT use in areas where water can accumulate or in rain or mist
CAUTION: Risk of Electric Shock – For Light Duty Dry Location Use Only
IMPORTANT SAFETY INSTRUCTIONS
This product has a polarized plug (one blade is wider than the other). As a safety feature, this
plug will fit in a polarized outlet only one way. If the plug does not fit fully in the outlet, reverse
the plug. If it still does not fit, contact a qualified electrician. Never use with an extension cord
unless the plug can be fully inserted. Do not attempt to defeat this safety feature.
WARNING: NOT FOR USE IN HAZARDOUS LOCATIONS
CAUTION: DO NOT USE IN HAZARDOUS LOCATIONS AS REQUIRED BY THE
CANADIAN ELECTRICAL CODE, PART I
OPERATION
Plug into 120 Volt 60 Hz polarized outlet. Notice the polarized plug and insert properly.
Operate switch. Lamp may flash several times before lighting.
1. Turn on the right hand switch button and then push the left-hand primer switch
2. Hold for several seconds until the lamp begins to light at each end.
3. Release the primer switch and the lamp will come on.
4. NOTE: The switch must be on and the primer depressed to start the lamp
5. Release the primer with the switch on to start the lamp.
6. Even new lamps will take several seconds to prime
BULB REPLACEMENT
Do not remove work light ends while unit is plugged in
1. Unplug the work light before changing the bulb
2. Remove the lens cover black plastic rivets located on each end of the tube lens.
3. Pull the far end plate socket from the lens end.
4. Carefully slide the lens over and away from the bulb.
5. Carefully pull the tube bulb from the bulb socket.
6. Carefully insert new bulb in the handle socket. Be sure bulb is properly seated.
7. Push the lens back into place on the lamp bottom, align the rivet boles and replace
the rivet.
8. Push the far end plate into the lens end and over the two lamp terminals.
9. Be sure the far end plate socket is properly aligned with the terminals.
10. Align the lens and far lens cover rivet holes, and replace the rivet.
11. Make sure both ends are seated and the rivets are tight
12. Plug in the light and test by pressing the power switch and the primer
NOTE: Even new lamps will flash several times before lighting.
REPLACEMENT BULBS
Use PL- 15 Quad pin Type-T fluorescent bulbs. Replacement bulbs are available from
Bayco.
WARRANTY
BAYCO • 640 South Sanden Blvd. • Wylie, TX 75098 • 1-800-233-2155 • www.baycoproducts.com
PRODUCTS COVERED UNDER THIS LIMITED WARRANTY:
This product is warranted to the original purchaser for 1 year and only covers failures due
to defects in materials or workmanship. If this product is used for rental purposes, the
warranty term is reduced to 90 days from the date of purchase.
NOT COVERED
The warranty does not cover normal wear and tear or cosmetic damage. The Limited
Warranty also does not cover damages which occurred in shipment or failures which are
caused by accidents, misuse, abuse, faulty installation and lightning damage.
Consequential damages, incidental damages or incidental expenses, including damage
to property. Some states do not allow the exclusion or limitation of incidental or
consequential damages, so the above limitation or exclusion may not apply to you. This
warranty gives you specific legal rights, which may vary from state to state.
This warranty does not apply to certain Bayco professional products that carry a specific
warranty unique to those products.
WARRANTY CLAIMS - USA
Contact Bayco for USA warranty claims. Call 800-233-2155 and Bayco Customer
Service will provide a Return Goods Authorization (RGA) to facilitate rapid warranty
action. After receiving the RGA, send the product (shipping prepaid) to BAYCO • 640 S.
SANDEN BLVD • WYLIE, TEXAS • 75098. Include a dated proof of purchase and a brief
description of the defect with your name, address and phone number. Your product will
either be repaired or replaced at the option of Bayco and returned as soon as practical,
but no later than 45 days after being received by Bayco.
WARRANTY CLAIMS - CANADA
Return the product to the place where purchased with a dated proof of purchase and a
brief description of the defect with your name, address and phone number. Your product
will either be replaced or purchase price refunded.
REQUEST FOR WARRANTY ACTION
If you have any questions about this warranty or any other Bayco product inquiries
contact BAYCO • 640 S. SANDEN BLVD • WYLIE, TEXAS • 75098 or call 800-233-2155
Instructions Pour les Modèle 623
15 Watt Lampe de Travail Fluorescente
Caractéristiques électriques - 125 volts 60 Hz
ATTENTION - POUR RÉDUIRE LE RISQUE DE CHOC ÉLECTRIQUE ET INCENDIE -
RETIRER LA FICHE LORS DE L'ENTRETIEN, OU LORS D'UNE NOUVELLE
LAMPING - UTILISER SEULEMENT 15 WATTS OU MOINS AMPOULE
ATTENTION
NE PAS utiliser cet enrouleur de cordon dans des atmosphères explosives, près de
liquides inflammables, ou lorsque des lampes antidéflagrantes sont nécessaires.
NE PAS utiliser à proximité de véhicules ou d'équipement quand il ya un risque de
liquides inflammables entrent en contact avec la lampe de poche
Ne pas plonger dans l'eau
NE PAS utiliser dans les zones où l'eau peut s'accumuler ou dans la pluie ou le brouillard
ATTENTION: Risque de choc électrique - Pour la lumière endroit sec Duty Utilisez
uniquement
CONSIGNES DE SÉCURITÉ IMPORTANTES
Ce produit a une fiche polarisée (une lame est plus large que l'autre). Par mesure de
sécurité, cette fiche ne rentre dans une prise polarisée que dans un sens. Si la fiche
n'entre pas complètement dans la prise, inverser la fiche. Si elle ne convient toujours
pas, contactez un électricien qualifié. Ne pas utiliser avec une rallonge si la fiche peut
être insérée à fond. Ne pas essayer de contourner ce dispositif de sécurité.
ATTENTION: NE PAS UTILISER DANS DES ENDROITS DANGEREUX
ATTENTION: NE PAS UTILISER DANS DES ENDROITS DANGEREUX AS REQUIS
PAR LE CODE ELECTRIQUE CANADIEN, PARTIE I
FONCTIONNEMENT
Branchez dans une prise polarisée de 120 V, 60 Hz. Insérez correctement la fiche
polarisée.
1. Actionnez le bouton de mise en marche sur le côté droit et appuyez sur l'interrupteur
d'amorce sur le côté gauche.
2. Tenez-le pendant plusieurs secondes jusqu'à ce que l'ampoule commence à
s'allumer aux deux extrémités.