Bayco 918 Instructions

Instructions for Model 918
18 Watt Fluorescent Work Light
Electrical Rating - All models use 125 Volts 60 Hz
CAUTION - TO REDUCE THE RISK OF ELECTRIC SHOCK AND FIRE - PULL
PLUG WHEN SERVICING, CONNECTING/DISCONNECTING FROM THE LAMP OR
WHEN RE-LAMPING - USE ONLY 13 WATT OR SMALLER BULB
CAUTION
DO NOT use in explosive atmospheres, near fl ammable liquids, or where explosion
proof lamps are required.
DO NOT use in the proximity of vehicles or equipment when there is a risk of fl ammable
liquids coming into contact with the hand lamp.
DO NOT immerse in water.
DO NOT use in areas where water can accumulate or in rain or mist.
CAUTION: Risk of Electric Shock – For Light Duty Dry Location Use Only.
IMPORTANT SAFETY INSTRUCTIONS
This product has a 3 prong polarized plug on the power cord. Do not attempt to
bypass this safety feature by removing the round plug and defeat his safety feature. This
plug will fi t into a grounded outlet only one way. If the plug does not fi t fully into the outlet,
contact a qualifi ed electrician. Never use with a two wire extension cord.
WARNING: NOT FOR USE IN HAZARDOUS LOCATIONS
CAUTION: DO NOT USE IN HAZARDOUS LOCATIONS AS REQUIRED BY THE
CANADIAN ELECTRICAL CODE, PART I
OPERATION
Plug into 120 Volt 60 Hz polarized outlet. Notice the polarized plug and insert
properly. Operate switch. Lamp may fl ash several times before lighting.
Some models have a 3-wire grounded outlet as a power source for electrical tools
or other appliances not exceeding 6.4 AMPS. The outlet will also accept a two-wire
polarized plug.
Bayco Products, Inc. • 640 South Sanden Blvd. • Wylie, TX 75098 • 1-800-233-2155 • 1-469-326-9400 • www.mybayco.com
BULB REPLACEMENT
1. Disconnect the work light from electrical outlet.
2. Remove the top cap and hang hook assembly from the tube.
3. Remove the 2 screws located on the back of the light.
4. Slide the lens up to expose the bulbs.
5. Grasping the bulb at the top, rock the bulb back and forth while carefully pulling up
on bulb to remove and discard the old bulb.
6. Insert new bulb in socket and bulb holder. Be sure bulb is properly seated against the
bulb-holder.
7. Slide the lens back into place.
8. Align the holes in the lens with the holes in the back of the light. Replace the screws.
9. Replace the cap and hang hook assembly.
10. Restore power connection and test lamp by pressing the power switch
NOTE: Even new lamps will fl ash several times before lighting.
REPLACEMENT BULBS
Use PL-9 twin-tube fl uorescent bulb.
A replacement lamp may be obtained from Bayco products.
WARRANTY
1 YEAR WARRANTY
Bayco Products, Inc. warrants this product to be free from defects in workmanship
and materials to the original purchaser for 1 year from the date of purchase, and includes
the LEDs, housing, lenses, electronics, switches, rechargeable batteries and chargers.
Bulbs (other than LEDs) are covered for 90 days from the date of purchase.
We will repair or replace this product should we determine it to be defective. This is the
only warranty, expressed or implied, including any warranty of merchantability or fi tness for
a particular purpose.
For a complete copy of the warranty, go to www. baycoproducts.com/bayco-product-
support/warranties. Retain your receipt for proof of purchase.
Instructions Pour les
18 Watt Lampe de Travail Fluorescente
Caractéristiques électriques - Tous les modèles utilisent 125 volts 60Hz
ATTENTION - POUR RÉDUIRE LE RISQUE DE CHOC ÉLECTRIQUE ET INCENDIE
- RETIRER LA FICHE LORS DE L'ENTRETIEN, CONNEXION / DECONNEXION DE
LA LAMPE OU QUAND REMPLACEMENT DES LAMPES - UTILISER SEULEMENT
13 WATTS OU MOINS AMPOULE
ATTENTION
NE PAS utiliser des atmosphères explosives, près de liquides infl ammables, ou
lorsque des lampes antidéfl agrantes sont nécessaires.
NE PAS utiliser à proximité de véhicules ou d'équipement quand il ya un risque de
liquides infl ammables entrent en contact avec la lampe de poche.
Ne pas plonger dans l'eau.
NE PAS utiliser dans les zones où l'eau peut s'accumuler ou dans la pluie ou le
brouillard.
ATTENTION: Risque de choc électrique - Pour la lumière endroit sec Duty Utilisez
uniquement.
CONSIGNES DE SÉCURITÉ IMPORTANTES
Ce produit a une fi che à 3 broches polarisées sur le cordon d'alimentation. Ne pas
essayer de contourner ce dispositif de sécurité en retirant le bouchon rond et la défaite
de son dispositif de sécurité. Cette fi che dans une prise de terre une seule façon. Si la
fi che n'entre pas complètement dans la prise, contacter un électricien qualifi é. Ne pas
utiliser avec un cordon à deux fi ls d'extension.
ATTENTION: NE PAS UTILISER DANS DES ENDROITS DANGEREUX
ATTENTION: NE PAS UTILISER DANS DES ENDROITS DANGEREUX AS REQUIS
PAR LE CODE ELECTRIQUE CANADIEN, PARTIE I
INS-918-18
Modèles 918