Download Print this page

Whirlpool MK1197XH Installation Instruction

Built-in trim kit

Advertisement

Quick Links

BUILT-IN TRIM KIT INSTALLATION INSTRUCTION
FOR WHIRLPOOL TRIM-KIT MODELS: MK1197XH, MK1190XH
• FOR USE WITH WHIRLPOOL MICROWAVE OVEN MODELS : MT1195SG, GT1196SH,
GT1195SH, MT3185SH, 89990, 89999, 89998, (Y)KCMS185J, MT2210SJ
UL LISTED - FOR USE OVER ELECTRIC HEAT SOURCE
(INCLUDING MODELS - 27": (Y)RBS275PD, (Y)GBS277PD, KEBI171D, (Y)KEBS177D
PARTS LIST
CUTOUT DIMENSIONS
27 "
Height
16
1 /2
Width
25
Depth
21
"
with flush mount receptacle.
3 /4
(min.)
(22
used)
(KEEP FOR FURTHER REFERENCE)
- 30": (Y)RBS305PD, GBS307PD, (Y)KEBI101D, (Y)KEBS107D)
Trim Kit
Bottom Duct (1)
Side Duct (1)
30 "
3 /4
"
1 /2
" 25
"
(min.),
28
"
if non-flush receptacle is
1 /2
"
(max.)
1" Screws
(4 Req'd 2 Extra)
1/2" Screws
(11 Req'd 2 Extra)
Anti-Tip
Bracket (1)
Bottom
Bracket (1)
Upper Duct (1)
Template (1)
Depth
Width
P/NO.: 3828W5U0085/8172239
Height
3" Min.

Advertisement

loading

Related Manuals for Whirlpool MK1197XH

Summary of Contents for Whirlpool MK1197XH

  • Page 1 BUILT-IN TRIM KIT INSTALLATION INSTRUCTION (KEEP FOR FURTHER REFERENCE) FOR WHIRLPOOL TRIM-KIT MODELS: MK1197XH, MK1190XH • FOR USE WITH WHIRLPOOL MICROWAVE OVEN MODELS : MT1195SG, GT1196SH, GT1195SH, MT3185SH, 89990, 89999, 89998, (Y)KCMS185J, MT2210SJ • UL LISTED - FOR USE OVER ELECTRIC HEAT SOURCE (INCLUDING MODELS - 27”: (Y)RBS275PD, (Y)GBS277PD, KEBI171D, (Y)KEBS177D...
  • Page 2 STEP 1 WARNING Electrical Shock Hazard Disconnect power before installing trim kit. Replace all panels before operating. Failure to do so can result in death or electrical shock. Front 1. Disconnect the microwave oven before proceeding with installation. 2. Remove any loose items inside the microwave Rear oven.
  • Page 3 STEP 3 1. On the cutout floor, mark hole centers for the anti-tip brackets as shown using the supplied template. Be sure to align the center line of template to center line of cutout floor. 2. Drill two holes for anti-tip bracket. ”...
  • Page 4 STEP 5 Pilot Hole Cutout 1. Place the trim kit frame over the microwave oven. Opening Important Note : Trim kit frame orientation is "A" important. Orient the frame so that louvers are sloping downward to the front. (See Figure Detail A). 2.
  • Page 5: Liste Des Pièces

    GARNITURES POUR MODÈLE ENCASTRÉ INSTRUCTIONS D´INSTALLATION (DOCUMENTS À CONSERVER) Ensemble de garnitures pour modèles Whirlpool: MK1197XH, MK1190XH • POUR UTILISATION AVEC LES FOURS À MICRO-ONDES WHIRLPOOL MODÈLES : MT1195SG, GT1196SH, GT1195SH, MT3185SH, 89990, 89999, 89998, (Y)KCMS185J, MT2210SJ • HOMOLOGATIONS UL ET ACNOR - POUR UTILISATION AU-DESSUS D´...
  • Page 6 ÉTAPE 1 AVERTISSEMENT Risque de choc électrique Interrormpre l´alimentation électrique avant d´installer l´ensemble de garniture. Réinstaller chaque panneau avant de faire fonctionner l´appareil. Le non-respect de ces instructions peut provoquer accident mortel ou choc électrique. AVANT 1. Débrancher le four à micro-ondes avant d´entreprendre l´installation.
  • Page 7 ÉTAPE 3 1. Sur le plancher d´encastrement, marquer le centre des trous pour la bride antibasculement tel qu´illustré sur le gabarit fourni. S´assurer de bien aligner la ligne centrale du gabarit à la ligne centrale du plancher d´encastrement. 2. Percer deux trous pour les brides antibasculement.
  • Page 8 ÉTAPE 5 Avant-trou Ouverture de 1. Placer le cadre de garniture sur le four à la cavité micro-ondes. "A" Note importante : Orienter le cadre de telle manière que les lames de la claire-voie soient inclinées vers l´avant. (Voir la figure-détail A) Vis 1 po 2.

This manual is also suitable for:

Mk1190xh