Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Schwank MonsterFans Style Series
Summary of Contents for Schwank MonsterFans Style Series
- Page 1 MonsterFans Style Series Installation Manual schwankgroup.com/monsterfans...
-
Page 2: Table Of Contents
Table Of Contents Overview Components Overview .............................. 3 Illustrations may be changed without notice. All dimensions and specifications are approximate and Components ..........................3 drawings are not to scale. Specifications are subject to change without notice. Technical Data ............................ 4 Fusing and Thermal Limiting ....................... -
Page 3: Fusing And Thermal Limiting
Technical Data Fusing and Thermal Limiting Fuses Conformity Low Voltage [2006/95/EC] & EMC [2004/108/EC] It is recommended that the following fuses for protecting the equipment and subject to local Directives authority: EN61000-6-2:2005, EN61000-6-4:2007 For 220-240 VAC use a fast blow fuse rated 5 Amps. IEC 60335-2-80:2015 IEC 60335-1:2015 For 110-120 VAC use a fast blow fuse rated 10 Amps. -
Page 4: Clearances
Contractor is responsible for verifying all site conditions to include field dimensions where applicable. If the contractor elects to make any changes without notifying Schwank Ltd. the contractor is responsible for the same. All drawings are to be used as general architectural intent unless otherwise stamped. -
Page 5: Tools Required
Appropriate personal protective equipment • Drill [optional] • Drill bit set up to ½” diameter [optional] Only use mounting hardware/ brackets supplied by MonsterFans Style Series. Glu-Lam Mount Items Included • Motor Assembly • [5] Blades [Optional Color] •... - Page 6 Installation Procedure Installation Procedure Purlin Mount 1. Level the mounting brackets and mark the centre of the top two mounting holes. Drill the remaining top two mounting holes. 1. From an accessible landmark, on the first purlin, measure to the centre line of the bottom centered hole of the 3 mounting holes.
- Page 7 Installation Procedure Installation Procedure OWSJ Mount [Open Web Steel Joist] Wood Truss Mount 1. Insert two 3/8” X 9” long thread rod with welded nut through the studded mounting plate pointing 1. Place round stand-off on top of flange of fan assembly. upward.
-
Page 8: Installing The Blades
Installation Procedure Installing the Optional LED Light Kit Caution! to reduce the risk of fire, electric shock, 5. Ensure wires are not compromised and tighten ¼” nylock nuts to secure the motor assembly to the studded mounting assembly. or injury to persons, disconnect the electrical supply circuit to the fan before installing light kit. -
Page 9: Installing The Hub Cover [With Lens]
Installing the Optional LED Light Kit Electrical Installation Installing the Hub Cover [with Lens] Wiring the Fan A means of disconnect must be incorporated in the fixed wiring in accordance with electrical codes and standards. DO NOT LIFT, CARRY, OR HANG FAN BY POWER CABLE. This could possibly cause the safety disconnect system to disconnect power to the fan. -
Page 10: Hmi Control
Electrical Installation HMI Control HMI/CAT 5 Cable Connection Input: 120/240V 2.9/1.45A 1 PH 75ft of Cat 5 cable is supplied to connect the HMI to the fan. This is a simple “plug and play” 50/60Hz LED: application once the cable is ran. Level and install HMI within reach of the 75ft CAT 5 cable using supplied fasteners. -
Page 11: Maintenance
Maintenance Maintenance Maintenance Schedule Warning! Risk of shock! Only qualified personnel to remove drive cover! There is no Initial Six Months adjustments or replacement parts for the use! • Check for hot spots Terminals: • Re-tighten all loose electrical connections Power Terminal: 3A, 300V, 10-30 AWG Torque = 0.5-0.6 Nm [0.37-0.44 ft-lb] I/O Terminal: 17.5A, 300V, 12-30 AWG Torque = 0.6-0.8 Nm [0.44-0.59 ft-lb] •... - Page 12 Toll Free: 1-877-446-3727 1-706-554-6191 monsterfans@schwankgroup.com Canada 2 Schwank Way, 5285 Bradco Blvd., Waynesboro, GA Mississauga, ON 30830 L4W 2A6 schwankgroup.com/monsterfans...