Maintenance - AEG OMNI 18C-PB Original Instructions Manual

APPROVAL
This application head is approved for use on the following
powerbases:
OMNI 18C-PB......................................................... 18 V-
OMNI 300-PB ................................................ 220-240 V ~
TECHNICAL DATA OMNI-MTX
Production code.................................................4467 09...
...00001-99999
Oscillating angle left/right .................................... 2/2 °
Deltasander no load oscillation frequency ........ 20000 min
Weight according EPTA-Procedure 01/2014 ....... 0.47 kg
Vibration Information
Total vibration values (vector sum in the three axes)
determined according to EN 62841.
Vibration emission value a
h
Sanding
OMNI 18C-PB .................................................. 7.4 m/s
OMNI 300-PB ................................................ 12.8 m/s
Uncertainty K = ................................................ 1.5 m/s
Sawing (Multifunctionhead)
OMNI 18C-PB .................................................. 8.9 m/s
OMNI 300-PB .................................................11.6 m/s
Uncertainty K = ................................................ 1.5 m/s
For technical data and approvals of powerbases for use with
various application heads please refer to the operating
instructions of the used powerbase.
WARNING
The vibration emission level given in this information sheet
has been measured in accordance with a standardised test
given in EN 62841 and may be used to compare one tool
with another. It may be used for a preliminary assessment of
exposure.
The declared vibration emission level represents the main
applications of the tool. However if the tool is used for
diff erent applications, with diff erent accessories or poorly
maintained, the vibration emission may diff er. This may
signifi cantly increase the exposure level over the total
working period.
An estimation of the level of exposure to vibration should
also take into account the times when the tool is switched
off or when it is running but not actually doing the job. This
may signifi cantly reduce the exposure level over the total
working period.
Identify additional safety measures to protect the operator
from the eff ects of vibration such as: maintain the tool and
the accessories, keep the hands warm, organisation of work
patterns.
WARNING Read all safety warnings, instructions,
illustrations and specifi cations provided with this power
tool. Failure to follow all instructions listed below may result
in electric shock, fi re and/or serious injury.
Save all warnings and instructions for future reference.
14 ENGLISH
SANDER SAFETY WARNINGS
Wear ear protectors. Exposure to noise can cause hearing
loss.
Hold the power tool by insulated gripping surfaces,
when performing an operation where the cutting
accessory may contact hidden wiring. Cutting accessory
contacting a "live" wire may make exposed metal parts of
the power tool "live" and could give the operator an electric
shock.
-1
ADDITIONAL SAFETY AND WORKING INSTRUCTIONS
Use protective equipment. Always wear safety glasses when
working with the machine. The use of protective clothing is
recommended, such as dust mask, protective gloves, sturdy
non-slip footwear, helmet and ear defenders.
The dust produced when using this tool may be harmful to
2
health. Do not inhale the dust. Wear a suitable dust
2
protection mask.
2
Do not machine any materials that present a danger to
2
health (e.g. asbestos).
2
Switch the device off immediately if the insertion tool stalls!
2
Do not switch the device on again while the insertion tool is
stalled, as doing so could trigger a sudden recoil with a high
reactive force. Determine why the insertion tool stalled and
rectify this, paying heed to the safety instructions.
The possible causes may be:
• it is tilted in the workpiece to be machined
• it has pierced through the material to be machined
• the power tool is overloaded
Do not reach into the machine while it is running.
The insertion tool may become hot during use.
WARNING! Danger of burns
• when changing tools
• when setting the device down
Chips and splinters must not be removed while the machine
is running.
When working in walls ceiling, or fl oor, take care to avoid
electric cables and gas or waterpipes.
Clamp your workpiece with a clamping device. Unclamped
workpieces can cause severe injury and damage.
Do not use cracked or distorted saw blades.
Plunge cuts without pre-drilling a hole are possible with soft
materials (wood, light building materials for walls). Harder
materials (metals) must fi rst be drilled with a hole
corresponding to the size of the saw blade.
Remove the battery pack before starting any work on the
machine.
Always disconnect the plug from the socket before carrying
out any work on the machine.
The product will restart automatically if stalled. Switch off the
product immediately if it stalls. Do not switch on the product
again while it is still stalled, as doing so could trigger a
sudden recoil with a high reactive force. Determine why the
product stalled and rectify this, paying heed to the safety
instructions.
SPECIFIED CONDITIONS OF USE
Combined with an AEG OMNIPRO powerbase the
Multifunction head with sander pad is designed
wood, metal and plastics and the Multifunction head with
saw blades is designed for cutting fl ush to a surface in wood
and plastics.
Do not use this product in any other way as stated for
normal use.
EC-DECLARATION OF CONFORMITY
We declare as the manufacturer under our sole
responsibility that the product described under "Technical
Data" fulfi lls all the relevant regulations and the directives
2011/65/EU (RoHS), 2014/30/EU, 2006/42/EC, and the
following harmonized standards have been used:
EN 62841-1:2015
EN 62841-2-4:2014
EN 55014-1:2017+A11:2020
EN 55014-2:2015
EN IEC 63000:2018
Winnenden, 2021-01-09
Alexander Krug
Managing Director
Authorized to compile the technical fi le.
Techtronic Industries GmbH
Max-Eyth-Straße 10
71364 Winnenden
Germany
GB-DECLARATION OF CONFORMITY
We declare as the manufacturer under our sole
responsibility that the product described under "Technical
Data" fulfi lls all the relevant provisions of the following
Regulations S.I. 2008/1597 (as amended), S.I. 2016/1091
(as amended), S.I. 2012/3032 (as amended) and that the
following designated standards have been used:
BS EN 62841-1:2015
BS EN 62841-2-4:2014
BS EN 55014-1:2017+A11:2020
BS EN 55014-2:2015
BS EN IEC 63000:2018
Winnenden, 2021-01-09
Alexander Krug
Managing Director
Authorized to compile the technical fi le.
Techtronic Industries GmbH
Max-Eyth-Straße 10
71364 Winnenden
Germany

MAINTENANCE

Use only AEG accessories and spare parts. Should
components need to be replaced which have not been
described, please contact one of our AEG service agents
(see our list of guarantee/service addresses).
sanding
If needed, an exploded view of the tool can be ordered.
Please state the machine type printed as well as the six-digit
No. on the label and order the drawing at your local service
agents or directly at: Techtronic Industries GmbH,
Max-Eyth-Straße 10, 71364 Winnenden, Germany.
SYMBOLS
CAUTION! WARNING! DANGER!
Remove the battery pack before starting any
work on the machine
(OMNI 18C-PB).
Always disconnect the plug from the socket
before carrying out any work on the machine
(OMNI 300-PB).
Please read the instructions carefully before
starting the machine.
Do not dispose electric tools, batteries/
rechargeable batteries together with
household waste material.
Electric tools and batteries that have reached
the end of their life must be collected
separately and returned to an environmentally
compatible recycling facility.
Check with your local authority or retailer for
recycling advice and collection point.
Warning! Hot Surface! Do not touch!
European Conformity Mark
British Confomity Mark
National mark of conformity Ukraine
EurAsian Conformity Mark.
ENGLISH 15