Mitsubishi Electric PLA-A.EA7 Operation Manual page 11

. Operation
Con r ation proce ure ire re ote controller
Manual vane angle
Ref. address
Unit No.
Identify unit Check button
Input display:
Cur. Address Check
F1 F2 F3 F4
Manual vane angle
Ref. address
Unit No.
Function setting for unit
with vane fully open.
Return:
F1 F2 F3 F4
Manual vane angle
No communication
Check Unit state.
Return:
F1 F2 F3 F4
.6. D i-see Sensor setting
Note:
This function cannot e set epen ing on the out oor unit to e
connecte .
.6.1 D i-see Sensor setting
Main Main menu
Maintenance
Initial setting
Service
Main display:
Cursor Page
F1 F2 F3 F4
Maintenance menu
Auto descending panel
Manual vane angle
3D i-See sensor
Main menu:
Cursor
F1 F2 F3 F4
1
address" to 0 and "Unit No." to 1.
or "Unit No." with the [F1] button to
select.
the unit number for the units to
the [F2] or [F3] button, and press
the [SELECT] button.
the unit.
2 Change the "Unit No." in order and
check each unit.
"Unit No.".
Press the [F2] or [F3] button to
change the "Unit No." to the unit
that you want to check, and then
press the [F4] button.
approximately 15 seconds, and
then check the current state of the
air conditioner.
on the remote controller.
Press
the [RETURN] button and continue
the operation from the beginning.
device does not exist at this refrig-
erant address.
return to the initial screen.
3 Change the "Ref. address" to the
next number.
1 to change the
"Ref. address" and continue with
1 Select "Maintenance" from the
Main menu (refer to page 8), and
press the [SELECT] button.
2 Select "3D i-See sensor" with the
[F1] or [F2] button, and press the
[SELECT] button.
3D i-See sensor
Air distribution
Energy saving option
Seasonal airflow
Setting display:
Cursor
F1 F2 F3 F4
.6.2 Air istri ution
Air distribution
Ref. address
Unit No.
Identify unit Check button
Input display:
Cur. Address Check
F1 F2 F3 F4
Air distribution
Ref. address
Unit No. All
Auto vane
Direct/Indirect
Direct/Indirect setting
Select:
Cur.
F1 F2 F3 F4
Direct
Cooling
Heating
keep downward
3 Select the desired menu with the
[F1] or [F2] button, and press the
[SELECT] button.
is set to "Auto".
Operates the energy-save mode
according to whether persons are
detected in the room by the 3D
i-see Sensor.
When the thermostat turns off, the
fan and the vanes operate accord-
ing to the control settings.
1 Move the cursor to "Ref. address"
or "Unit No." with the [F1] button to
select.
Select the refrigerant address and
the unit number for the units to
the [F2] or [F3] button, and press
the [SELECT] button.
the unit.
The vane of only the target indoor
unit is pointing downward.
2 Select the menu with the [F4] but-
ton.
Default: The vanes move the
same as during normal operation.
"Area"*: The vanes move to the
ture during Cool mode and toward
during Heat mode. Otherwise,
the vanes move to the horizontal
"Direct/Indirect"*: The vanes
automatically move relative to the
areas where persons are detect-
ed.
The vanes operate as indicated in
the following table.
* In order to enable this function,
"Auto".
Vane setting
Indirect
keep horizontal
-
11