Subscribe to Our Youtube Channel
Related Manuals for King Pigeon S175
Summary of Contents for King Pigeon S175
- Page 1 GSM 3G 4G LTE Cellular IoT Gateway S175 S375 User Manual Ver 1.5 Date Issued: 2020-07-29 King Pigeon Hi-Tech. Co., Ltd. www.IOT-Solution.com...
-
Page 2: Table Of Contents
7.1 Export Profile..............................26 7.2 Load Profile...............................27 7.3 Reset.................................28 8. Connection and Application............................28 8.1 Wire Connection.............................. 28 8.2 Quickly Verify Device Communication Function..................... 29 8.3 Modbus RTU Slave Application........................30 Page 2 of 55 King Pigeon Hi-Tech. Co., Ltd. Ver 1.3... - Page 3 We recommend that the advice of a registered electrician be sought before any Installation work commences. King Pigeon Hi-Tech.Co., Ltd, its employees and distributors, accept no liability for any loss or damage including consequential damage due to reliance on any material contained in this handbook.
- Page 4 Notice 2. For 3G WCDMA, 4G LTE version, please tell our sales where would you like to use them. 3. The S175 ,375E series has no communication module, so it can't call and SMS to alarm. Page 4 of 55 King Pigeon Hi-Tech.
-
Page 5: Brief Introduction
Gateway X1; AC/DC Adaptor X1; GSM/3G/4G Antenna X1;User Manual X1; PC Configurator X1 . Note: The package does not include any SIM card. Optional: 35mm Standard DIN rail fixed Bracket Page 5 of 55 King Pigeon Hi-Tech. Co., Ltd. Ver 1.3... -
Page 6: Features And Specification
Support SMS, dial, GPRS, 3G , 4G network for alert, USB port for configuration and upgrade firmware; Inbuilt large capacity automatically rechargeable backup battery, alert when external power failure; Support TCP/UDP, Modbus TCP, Modbus RTU over TCP, King Pigeon IoT RTU protocol and data transparent transmission function;... -
Page 7: Specifications
Internal 8G SD card inside, can save the data for 100000events. Memory Capacity Backup Battery 3.7V 1200mAH Temperature range -10°C ~ +70 °C Humidity range Relative humidity 95% (condensation free) Exterior dimension 70mm*88mm*30mm 500g Net Weight Page 7 of 55 King Pigeon Hi-Tech. Co., Ltd. Ver 1.3... -
Page 8: Physical Layout And Installation Diagram
5. Physical Layout and Installation Diagram 5.1 Control Unit size (Front view) (Left side view) (Right side view) Top view (Upward view) (Bottom view) 5.2 Interface definition Function Description Page 8 of 55 King Pigeon Hi-Tech. Co., Ltd. Ver 1.3... -
Page 9: Led Indicator Definition
Negative electrode. Power source output port, DC_OUT + positive electrode. External DC Power input DC_IN - port,negative electrode. External DC Power input DC_IN + port,positive electrode. 5.3 LED Indicator Definition Page 9 of 55 King Pigeon Hi-Tech. Co., Ltd. Ver 1.3... - Page 10 Work Side all the time. SIM Card Slot SIM Card Slot For SIM Card Installation, only supports 1.8V/3V SIM Card Ethernet Connector Definition(only for S37X) Page 10 of 55 King Pigeon Hi-Tech. Co., Ltd. Ver 1.3...
-
Page 11: Settings&Operation
XP or Windows 7 or Win8/Win10, please see the below photo. Also, the driver for different OS can be downloaded from Silicon Laboratories, Inc. http://www.silabs.com , the model is CP210x. Page 11 of 55 King Pigeon Hi-Tech. Co., Ltd. Ver 1.3... - Page 12 Choose the correct "COM port" in device manager above, enter the password(default is 1234),click the "OK" to connect and start to program Details please check the picture as below: Page 12 of 55 King Pigeon Hi-Tech. Co., Ltd. Ver 1.3...
-
Page 13: Setting Self-Checking
Solution: Back to Set mode---->Click "Save" Button after setting one page in the parameter setting menu. Terms usually used by Cellular IoT Gateway Cellular IoT RTU, Modbus RTU, Modbus Master, Modbus Slave, Modbus RTU Over TCP, Modbus TCP, Arm, Disarm... Page 13 of 55 King Pigeon Hi-Tech. Co., Ltd. Ver 1.3... -
Page 14: Configuration Software Interface And Running
4. Reboot the device, switch the Power Switch to OFF, then switch it to ON, the device will enter into normal running mode after that. Basic Settings Reminder: Please click the "Read" for previous parameter before starting to set. Page 14 of 55 King Pigeon Hi-Tech. Co., Ltd. Ver 1.3... -
Page 15: Number Settings
Synchronous machine time: This is to setup the RTU’s time for daily report or other timers. After click Write the RTU Time, the RTU will be synchronous the same time as the PC. If connect to King Pigeon Cloud Server, no need this step. -
Page 16: T&H Trigger Settings
SMS to this number. T&H Trigger Settings This page is to setup the temperature/humidity input alarm conditions parameter. It can be used for monitoring temperature and humidity, can be connected as below: Page 16 of 55 King Pigeon Hi-Tech. Co., Ltd. Ver 1.3... -
Page 17: T&H Alarm Settings
This page is for setup while temperature/humidity alarm, send SMS & Dial to which authorized numbers. Tick it stands for enable to send SMS or dial the related authorized number. Page 17 of 55 King Pigeon Hi-Tech. Co., Ltd. Ver 1.3... -
Page 18: Timer Settings
Tick it stands for enable this timer event: Reminder: When GPRS/3G/4G data transmission protocol is King Pigeon IoT RTU Protocol, the periodically auto upload default enable and upload every 5 minutes. Tick stands for enable this timer function, otherwise is disable. -
Page 19: Interlock Settings
RS485 Serial Port Settings This page is for setup the serial port parameters. Over the RS485, the S275 RTU can be used as Modbus RTU Slave, Modbus RTU Master and transparent transmission. Page 19 of 55 King Pigeon Hi-Tech. Co., Ltd. Ver 1.3... -
Page 20: Slave Settings
Note:When adding a slave, first read the list of slaves that have been mapped to prevent the new slave covering the added slave device. Page 20 of 55 King Pigeon Hi-Tech. Co., Ltd. Ver 1.3... - Page 21 Mapping Address Starting Address: Stand for mapping the slave start register data to the device start mapping address. Mapping Address End Address: Calculate the end mapping address according to start address and reading data quantity. Page 21 of 55 King Pigeon Hi-Tech. Co., Ltd. Ver 1.3...
-
Page 22: Register Settings
Domain: modbus.dtuip.com, Port: 6655. 3) King Pigeon IoT RTU protocol, transmit the King Pigeon IoT protocol on TCP, to commucation with upper computer system. Advantage is when device unnormal, can send data to upper system automatically, not waiting for polling ,then answer. - Page 23 Login Packets: Server register handshake protocol package. When transparent transmission or Modbus protocol, this item used for device ID, provided by cloud. Contact King Pigeon sales if need to connect www.my-m2m.com cloud server. Login ACK Packets: Once set, device need response within 10 seconds after device send login message, otherwise it will continue send login message according to "Reconnection Times"...
-
Page 24: Ethernet Settings(Only For S37X)
GSM/SMS/GPRS/3G/4G Cellular IoT Gateway provided by cloud.Contact King Pigeon sales if need to connect www.my-m2m.com cloud server. MQTT User Name: User accounts using the MQTT protocol. MQTT Password: User password using the MQTT protocol. Ethernet Settings(only for S37X) Get IP address automatically: Tick it stands for: the device automatically obtains the IP address in the LAN. -
Page 25: Historical Record
Cellular IoT Gateway Login Packets: Server register handshake protocol package. When transparent transmission or Modbus protocol, this item used for device ID, provided by cloud. Contact King Pigeon sales if need to connect www.my-m2m.com cloud server. Login ACK Packets:Once set, device need response within 10 seconds after device send login message, otherwise it will continue send login message according to "Reconnection Times"... -
Page 26: Configuration And Reset
The Load Profile and Export Profile is very useful while you need to program bulks of RTU with similar parameters. The “Default” function can reset the device to factory default status. 7.1 Export Profile Click “Export Profile” button----> chose the path and input the name to save. Page 26 of 55 King Pigeon Hi-Tech. Co., Ltd. Ver 1.3... -
Page 27: Load Profile
GSM/SMS/GPRS/3G/4G Cellular IoT Gateway Then it will display as below after a moment: 7.2 Load Profile Click “Load Profile” button----> chose the file which need to load. Page 27 of 55 King Pigeon Hi-Tech. Co., Ltd. Ver 1.3... -
Page 28: Reset
7.3 Reset When device is on, connect the PC configuration software, click the “Default” button on software to reset. It will restore all parameters of the device to the factory default initial value.Please contact King Pigeon sales if forget password,website www.gprs-m2m.com. -
Page 29: Quickly Verify Device Communication Function
In “Basic Settings” page, click [Read the RTU Time] > [Write the RTU Time] to write the correct time to the device.Choose [Arm automatically when power on]. Then click the [Save]. As below: Page 29 of 55 King Pigeon Hi-Tech. Co., Ltd. Ver 1.3... -
Page 30: Modbus Rtu Slave Application
Device support Modbus RTU slave function, can be connected to HMI, SCADA, DCS, MES system. It can be used for fieldbus data acquisition, remote SMS alarm, remote dial alarm and GPRS/3G/4G to cloud... Page 30 of 55 King Pigeon Hi-Tech. Co., Ltd. Ver 1.3... - Page 31 C) No need set: "Scan Rate", "Time Out", "Slave Fault Verify Time"; D) Click "Save" button. (4) In HMI configuration software, set the Modbus RTU Register address of device. Refer to [“S17X/S37X reigister”]; Page 31 of 55 King Pigeon Hi-Tech. Co., Ltd. Ver 1.3...
- Page 32 Read Register Qty total 2* 16 Bit register address 00 02H 16CRC Verify F1 CCH CRC0 CRC1 low byte in front, high byte in behind Receiver Return Data Format: Page 32 of 55 King Pigeon Hi-Tech. Co., Ltd. Ver 1.3...
-
Page 33: Modbus Rtu Master Application
Step2: Find the salve port communication parameter and register address from user manual. Step3: Write device RS485 parameter according to slave port communication parameter, pls ensure both parameter are same, others communication failure, refer to "port setting" part. Page 33 of 55 King Pigeon Hi-Tech. Co., Ltd. Ver 1.3... - Page 34 Stop Bit parameter need to be same as connected device; Scan Rate, Time Out and Slave Failure Verify Time can be set as default: Step5: Back to Slave Mapping page as below, right click the line to add. Click Add Slave as below: Page 34 of 55 King Pigeon Hi-Tech. Co., Ltd. Ver 1.3...
- Page 35 SMS and call. If set the network communication function, then can remote transmit data to cloud server via GPRS/3G/4G. Reminder: After adding slaves, device switched off/on to restart is necessary. Page 35 of 55 King Pigeon Hi-Tech. Co., Ltd. Ver 1.3...
- Page 36 Invalid address Value Register mapping address Value The address value higher than 10 digits will be seen as invalid. 5D OC =CRC verify. 8.4.2 Modify Boolean Mapping Address Data: Page 36 of 55 King Pigeon Hi-Tech. Co., Ltd. Ver 1.3...
- Page 37 8.4.3 Read Data Type Mapping Address Data: Master Send Data Format: Data Content Bytes Description (H: HEX) Device Address 01H Device, Range: 1-247, according to setting address Function Code Read holding coil, function code 03 Page 37 of 55 King Pigeon Hi-Tech. Co., Ltd. Ver 1.3...
- Page 38 Write single holding register, function code 06 Function Code Address range: 4E 20H-50 1CH. Mapping data type Mapping Register 4E 20H address range, refer to [“Slave Mapping Register Address Address”] at manual bottom. Page 38 of 55 King Pigeon Hi-Tech. Co., Ltd. Ver 1.3...
-
Page 39: Modbus Tcp Master Application
For example, when device as Modbus TCP master,as below: 1)Ethernet Setting: In “Ethernet Settings” page, choose correct slave IP and port,click “save” to add,support up to 5 Ethernet slave. Page 39 of 55 King Pigeon Hi-Tech. Co., Ltd. Ver 1.3... - Page 40 If one slave have multi register, then need to add separately according to register type; For example, Mxxx remote I/O module, with digital and analog inputs, need to add the digital(Boolean) first, then add the Page 40 of 55 King Pigeon Hi-Tech. Co., Ltd. Ver 1.3...
- Page 41 Range: 0040H-007FH, address refer to ["Slave 00 40H Starting Address Mapping Register Address”] at manual bottom Read Register Qty 00 0AH Range：0001H-0004H Receiver Return Data Format: Content Bytes Data Description Page 41 of 55 King Pigeon Hi-Tech. Co., Ltd. Ver 1.3...
- Page 42 00 00: Modbus protocol Data Length 00 06H The length of subsequent data Device Address 01H Device, Range: 1-247, according to setting address Function Code Write single holding coil, function code 05H Page 42 of 55 King Pigeon Hi-Tech. Co., Ltd. Ver 1.3...
- Page 43 Read holding register, function code 03 One address can read 2 bytes. Mapping data type Mapping Register 4E 20H address range, refer to [“Slave Mapping Register Starting Address Address”] at manual bottom. Page 43 of 55 King Pigeon Hi-Tech. Co., Ltd. Ver 1.3...
- Page 44 Description (H: HEX) Identification of Modbus requests/responses Transaction ID 00 00H transactions Protocol Identifier 00 00H 00 00: Modbus protocol Data Length 00 06H The length of subsequent data Page 44 of 55 King Pigeon Hi-Tech. Co., Ltd. Ver 1.3...
-
Page 45: Transparent Transmission Dtu Application
Modbus RTU protocol, then can choose transparent transmission as below: (1) Items connect to device via RS485, set RS485 port parameter; (2) Basic setting page to set device ID; Page 45 of 55 King Pigeon Hi-Tech. Co., Ltd. Ver 1.3... -
Page 46: Device Connect To Cloud Application
Device can connect to cloud and SCADA via GPRS/3G/4G network, also can connect to clients own server and King Pigeon www.My-M2M.com cloud server. King Pigeon my-m2m.com cloud as sample below: King Pigeon my m2m cloud support Modbus TCP, cloud configuration, wechat alarm function, welcomed editable function. - Page 47 (2) In "Cellular network" setting page, set parameter as below: When Communication Data as "Modbus RTU Protocol", then server IP/DNS should be: modbus.dtuip.com, port is 6651, pls contact King Pigeon Sales for "Login Message Writing"; Server domain/IP,device connecting port,Server 2 as back up Only support”Primary Server...
-
Page 48: Device Sms Command
Old Password＋P＋New Password This is the New Password, please remember it carefully. 4) Reboot SMS Command Return SMS Content Password+Reboot 5) Arm/Disarm SMS Command SMS Command Return SMS Content Page 48 of 55 King Pigeon Hi-Tech. Co., Ltd. Ver 1.3... - Page 49 11) Set GPRS APN/USER NAME/PASSWORD SMS Command Return SMS Content password+AP+apn+#+username+#+userpassword APN: User Name: Inquiry password+AP Password: Delete password+APDEL 12)GPRS Online SMS Command Return SMS Content password+GPRSonline GPRS always online 13)Delete Historical Data Page 49 of 55 King Pigeon Hi-Tech. Co., Ltd. Ver 1.3...
-
Page 50: S17X/S37X Register Address
16 Bit data 20001 REG20001 Same as above Same as above 20001 20002 16 Bit data REG20002 Same as above Same as above Page 50 of 55 King Pigeon Hi-Tech. Co., Ltd. Ver 1.3... - Page 51 Same as above 20260 64 Bit data 20264 REG20264 Same as above Same as above 20264 60 data ………. similar as ………. Same as above Same as above above Page 51 of 55 King Pigeon Hi-Tech. Co., Ltd. Ver 1.3...
- Page 52 1.Topic Publish of Devices 1)Device configuration 1.Domain name: the domain name of the broker (King Pigeon Cloud 2.0 default: mqtt.dtuip.com) 2. Port: the port of the broker (King Pigeon Cloud 2.0 default 1883) 3. MQTT device ID: The unique Identification of the device, which can be the serial number, device ID, sensor ID or IMEI number and mac address of the module chip, ensuring uniqueness and distinguishing from other devices.
- Page 53 GSM/SMS/GPRS/3G/4G Cellular IoT Gateway 4.MQTT account: The account of device publishing the topic to the broker (King Pigeon cloud 2.0 default account: MQTT) 5.MQTT password: The account password of device publishing the topic to the broker ( King Pigeon cloud 2.0...
-
Page 54: Upgrade Firmware
The device supports upgrade firmware via USB port directly. If you required upgrade, please contact us to discuss and modify the firmware according to you requirements, we can provide the upgraded firmware to you to upgrade them. Page 54 of 55 King Pigeon Hi-Tech. Co., Ltd. Ver 1.3... -
Page 55: Cellular Module Upgrade
Operating Instructions. In no event shall the manufacturer be liable for any alarm system altered by purchasers The End! Any questions please help to contact us feel free. Http://www.IOT-Solution.com Page 55 of 55 King Pigeon Hi-Tech. Co., Ltd. Ver 1.3...
Need help?
Do you have a question about the S175 and is the answer not in the manual?
Questions and answers