Related Manuals for UBTECH ADIBOT
Summary of Contents for UBTECH ADIBOT
-
Page 1: Content
UBTECH AIMBOT USER MANUAL USERS OF THE PRODUCT SERVICE MANUAL 产品用户手册 AI Fearless Clean Endless UBTECH ROBOTICS CORP LTD... -
Page 2: Table Of Contents
UBTECH AIMBOT USER MANUAL CONTENT CONTENT ............................1 Introduction ............................. 3 Part 1 Product Overview ........................4 1.1 Package List ........................4 1.2 Product View ........................5 1.3 System Framework ......................5 Part 2 Safety Information ......................... 6 2.1 Device Security ........................6 2.1.1 General ........................ -
Page 3: Introduction
◆ Thank you for purchasing ADIBOT equipment from UBTECH ROBOTICS CORP LTD. This user manual is only applicable to the operation of ADIBOT. ◆ In order to ensure safe use of ADIBOT and quickly grasp the usage method, please read this manual carefully. -
Page 4: Part 1 Product Overview
• Dosimeter cards *10 • UVC lamp *2 (back up) NOTE: • Remote controller use AAA battery *2 • Warning sign use AA battery *8 • AA battery and AAA battery are not equipped in ADIBOT UBTECH ROBOTICS CORP LTD... -
Page 5: Product View
UBTECH AIMBOT USER MANUAL 1.2 Product View Front: PIR infrared sensor, camera, UVC tube, reflector, push rod, horn, universal wheel with brake, Daisy chain. Back: switch key, emergency stop switch, chassis, fan port, charging port 1.3 System Framework A simple way to do job... -
Page 6: Part 2 Safety Information
Do not use robots to implement operations related to personal safety. 2.1.2 Operation Instruction Danger If there is no emergency, it is recommended not to touch it while ADIBOT is performing its task. Do not put your toes under the chassis of ADIBOT, as it may run over your toes. - Page 7 On uneven ground or slopes, please carefully push the equipment, especially the daisy chained equipment. When ADIBOT is working, please do not stand in direct contact with UVC light (unless you wear the necessary protective equipment), so as not to affect AIMBOT's task execution.
-
Page 8: Part 3 Device System Operation
NOTE: Remove the object or paper to ensure that the place or object that needs to be disinfected can be exposed to ultraviolet light Under the light. NOTE: If the home in the room moves, you need to move ADIBOT for a round of disinfecting. -
Page 9: Part 4 Web And Remote Controller Operation
Set and start the disinfecting task on the Web terminal; Plug the ADIBOT into the power source and press the switch on the back of the device base to start the device. After leaving the disinfecting site, the operator accesses the designated IP address to log in to the control software of the device through the mobile phone, sets various parameters on the software and executes the disinfecting task. -
Page 10: System Setting
The effective access of the software is realized through user login, and the management of ADIBOT business can be realized only after verifying the user and password. After logging in, you can view the work, life, and component status on the home page. -
Page 11: Task Management
UBTECH AIMBOT USER MANUAL password, reset the password forgotten, and remote networking mode. • Log in to the home page to learn about the working status, life status, and component status of the device. • Working status, display status, room, remaining time. The time and report link of the last kill mission. - Page 12 UBTECH AIMBOT USER MANUAL • Before starting the disinfection, ADIBOT will prompt the operator "prepare to kill, please leave as soon as possible, 20 seconds countdown." Please be sure to leave the disinfection scene within the specified time to avoid injury.
- Page 13 UBTECH AIMBOT USER MANUAL View disinfection points Configure parameters Task review Initiation countdown In disinfection Task complete UBTECH ROBOTICS CORP LTD...
-
Page 14: Report Management
UBTECH AIMBOT USER MANUAL Task pause Task terminated passively Task terminated proactively 4.1.4 Report Management The killing report list shows the results of all killing tasks. The marking task is aborted or completed. • The report has multiple entries: •... -
Page 15: Daily Maintenance
UBTECH AIMBOT USER MANUAL Report management hommage No Report Report - Starred Report - Room Report - Date 4.1.5 Daily Maintenance Routine and routine maintenance of the equipment. The maintenance content includes alarm, diagnosis, log, upgrade and restore. • The alarm module can obtain current system alarm information and recent historical alarm information, and users can operate on it according to their own management methods. -
Page 16: Remote Control Feature
Daily maintenance - Reset 4.2 Remote Control Feature In addition to the control of ADIBOT via the web-side software, ADIBOT can also be activated, paused, continued or terminated via the remote control. The remote control can be used as a kind of safe equipment to prevent the termination of no network or for... -
Page 17: Part 5 Transporting, Clean And Storage
Step 1 Activate the remote control First, you need to start ADIBOT. After 30 seconds, the software is started; then, set the remote control to be in the Bluetooth pairing state by ("Start" + "Continue" simultaneously press for 3 seconds). -
Page 18: Maintenance
Do not use abrasives, aerosols, alcohol-containing liquids or other liquids to clean ADIBOT, because they may contain flammable substances or may damage the plastic casing of ADIBOT; do not spray or shower ADIBOT with water or other liquids, please let ADIBOT Keep it dry. The product itself can be self-cleaning. -
Page 19: Replacement Parts
UBTECH AIMBOT USER MANUAL Main Processor Nvidia Nano 4GB RAM, 16GB ROM, 64G USB Storage Main Operating System Linux Wireless Module 2.4GHz/5Ghz Band 802.11b/g/n/ac, Bluetooth 5.0 Acoustics 1x 10W Speaker Environment sensors PIR Sensor Recording camera 2MP Front view , 480P... - Page 20 UBTECH AIMBOT USER MANUAL - 检查底盘电源插口是否松动异常； - 检 查 底 盘 开 关 机 按 键 是 否 松 动 异 ADIBOT 无法启动 常； -如果问题仍然存在，请联系 AIMBOT 技术支持中心。 -如果地盘太烫且您无法触摸它，这 可能是由故障引起的。 设备地盘过烫 -请迅速从插座断开，并联系 ADIBOT 技术支持中心。 Part 7 Declaration of Conformity 7.1 FCC compliance statement This device complies with Part 15 of the FCC Rules.
- Page 21 UBTECH AIMBOT USER MANUAL 7.2 FCC Radiation Exposure statement This equipment complies with FCC radiation exposure limits set forth for an uncontro lled environment. This equipment should be installed and operated with minimum distanc e 20cm between the radiator and your body. This transmitter must not be co- located or operating in conjunction with any other antenna or transmitter.