Advertisement

Door Contact (DC-16SL) User Manual
The Door Contact monitors the opening/closing of specified devices (e.g. door or window). The Door Contact is fixed to the
monitored device frame with an actuating magnet fixed to the device. When the door or window opens, the magnet moves
away from the Door Contact, activating an internal magnetic switch causing the Door Contact to transmit alarm signal to the
Control Panel. The device also has the capabilities of communicating signal problems along with low battery situations.
The Door Contact design is consisted of a cover and base. The cover contains all electronics and the base provides a
means for fixing the device. An enclosed PCB tamper switch provides tamper protection against unauthorized device
opening and/or removal.
I
d
e
n
t
i
f
y
i
n
g
t
I
d
e
n
t
i
f
y
i
n
g
t
1.
LED Indicator
2.
Learn / Test Button
- Press the Test button to transmit a learn code.
- Press the Test button once to enter Test Mode for 3 minutes.
3.
Battery
4.
Cover Securing Screw Hole
5.
Knockouts
6.
Tamper Switch
7.
Battery Insulator hole
8.
Rib Marks
9.
Magnet
- Mount the magnet on the side of the Door Contact where it has 2 rib-marks to indicate the position of the
internal magnet switch.
10. Magnet Screw hole
11. Magnet Spacer
A
c
c
e
s
s
o
r
i
e
s
A
c
c
e
s
s
o
r
i
e
s
a)
1 Magnet
b)
2 Screws
c)
2 Wall Plugs
d)
1 Magnet double-sided adhesive tape pad
e)
2 Magnet mounting screws
f)
2 Magnet spacers
L
E
D
I
n
d
i
c
a
t
o
L
E
D
I
n
d
i
c
a
t
o
In Normal operation mode, the LED indicator remains off except in the following situations:
When the Door Contact's tamper switch is triggered.
When the Door Contact is activated under Tamper or Low battery condition.
When the Door Contact is activated under Test mode.
If the LED flashes to indicate signal transmission, it will flash twice rapidly upon receiving acknowledgement from
the Control Panel.
h
e
p
a
r
t
s
h
e
p
a
r
t
s
I
n
c
l
u
d
e
d
I
n
c
l
u
d
e
d
r
r
1

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the DC-16SL and is the answer not in the manual?

Questions and answers

Summary of Contents for Climax Technology DC-16SL

  • Page 1 Door Contact (DC-16SL) User Manual The Door Contact monitors the opening/closing of specified devices (e.g. door or window). The Door Contact is fixed to the monitored device frame with an actuating magnet fixed to the device. When the door or window opens, the magnet moves away from the Door Contact, activating an internal magnetic switch causing the Door Contact to transmit alarm signal to the Control Panel.
  • Page 2    If enabled, the Door Contact will automatically transmit Supervisory signals to the Control Panel at random intervals of 15 to 18 minutes in Normal Operation Mode.  If the Control Panel has not received the signal from the Door Contact for a preset period time, the Control Panel will indicate that particular Door Contact is experiencing an out-of-signal problem.
  • Page 3  Screw Mounting The Base has two knockouts, where the plastic is thinner, for mounting purpose. To mount the Door Contact: Remove the cover by unscrewing the Cover Securing Screw using a Philips screwdriver. Break through the knockouts on the base. III.
  • Page 4 Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.

Table of Contents