Advertisement
Quick Links
Federal Communications Commission Statement
FCC Statement
This device complies with Part 15 of the FCC Rules. Operation is subject to the following
two conditions: (1) This device may not cause harmful interference, and (2) This device
must accept any interference received, including interference that may cause undesired
operation.
FCC Caution
To assure continued compliance, any changes or modifications not expressly
approved by the party responsible for compliance
may void the user's authority to operate his equipment. (Example – use only
shielded interface cables when connecting to computer or peripheral devices)
FCC Statement in User's Manual (for calss B) FCC Section 15.105 "Federal
Communications Commission (FCC) Statement"
This equipment has been tested and found to comply with the limits for a class B digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This
equipment generates uses and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one or more of the following
measures:
-- Reorient or relocate the receiving antenna.
-- Increase the separation between the equipment and receiver.
-- Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
-- Consult the dealer or an experienced radio/TV technician for help.
Limited Warranty
Vision Guarantees that every wireless ZB5311-5 is free from physical defects in material
and workmanship under normal use for one year from the date of purchase. If the product
proves defective during this one-year warranty period, Vision will replace it free of charge.
Vision does not issue any refunds. This warranty is extended to the original end user
purchase only and is not transferable. This warranty does not apply to: (1) damage to
units caused by accident, dropping or abuse in handling, or any negligent use; (2) units
which have been subject to unauthorized repair, taken apart, or otherwise modified; (3)
units not used in accordance with instruction; (4) damages exceeding the cost of the
product; (5) transit damage, initial installation costs, removal cost, or reinstallation cost.
For information on addtional devices, please visit us at www.visionsecurity.com.tw
ZB5311-5 V0
1090304
Installation & Operation Manual
Glass Break Detector
ZB5311IN-5
ZB5311EU-5
ZB5311RU-5
ZB5311US-5
ZB5311IL-5
ZB5311KR-5
ZB5311HK-5
ZB5311JP-5
ZB5311BR-5
Advertisement
Related Manuals for Vision ZB5311IN-5
Summary of Contents for Vision ZB5311IN-5
- Page 1 Vision will replace it free of charge. ZB5311US-5 Vision does not issue any refunds. This warranty is extended to the original end user ZB5311IL-5 purchase only and is not transferable. This warranty does not apply to: (1) damage to units caused by accident, dropping or abuse in handling, or any negligent use;...
- Page 2 Introduction Z-Wave S2 Support Command Class: COMMAND_CLASS_ASSOCIATION_V2 Thanks for choosing the Vision’s wireless Glass Break Detector (ZB5311-5) of the home security COMMAND_CLASS_ASSOCIATION_GRP_INFO device. This sensor is a Z-Wave™ Plus enabled device (interoperable, two-way RF mesh COMMAND_CLASS_BATTERY networking technology) and is fully compatible with any Z-Wave™ enabled network and its COMMAND_CLASS_DEVICE_RESET_LOCALLY security framework.
- Page 3 Operation Notice: If you are installing the entire Z-Wave™ system for the first time, please refer to the installation guide of Z-Wave™ Interface Controller. 1. For “Inclusion” in (adding to) a network: - SmartStart: Please scan the QR Code from glass break detector for SmartStart. QR code and PIN is located on the device, also there is a Full DSK string on the enclosed DSK card.
- Page 4 5. Auto Wake Up: 11. Support Explorer Frame Function Use “Wake Up” command to set up the awaking time and send the wake up notification to controller. User can use command to change the auto wake up from 12. All the rest commands depend on Z-Wave standard 10 minutes to 1 week, Interval increment is 200 seconds.