Cooper Lighting Solutions HALO ALS4A40GY Instruction Manual

6
D. POLE MOUNTING CLAMP
8 7
6
8
7
I. PHOTOCONTROL SENSOR
B. ACCESS COVER
F
C. MOUNTING SCREWS
A. LIGHT FIXTURE
F
E
ALS4A40GY
I. PHOTOCONTROL SENSOR
S COVER
B. ACCESS COVER
D
E
8
C F CONDUIT
CONDUITCONNECTOR
D
F. POLE MOUNTING CLAMP/ACCESS COVER MOUNTING SCREWS
FIGURE 1
A. LIGHT FIXTURE
E
B
ENGLISH
FIGURE 1
ITEMS REQUIRED
D
A (Purchase separately)
PRODUCT MUST CONFORM TO ROHS
COOPER LIGHTING SOLUTIONS - CONFIDENTIAL AND PROPRIETARY
NOTICE TO PERSONS RECEIVING THIS DOCUMENT AND/OR TECHNICAL INFORMATION • Phillips screwdriver
THIS DOCUMENT, INCLUDING THE DRAWING AND INFORMATION CONTAINED THEREON, IS
CONFIDENTIAL AND IS THE EXCLUSIVE PROPERTY OF EATON, AND IS MERELY ON LOAN
AND SUBJECT TO RECALL BY COOPER LIGHTING SOLUTIONS AT ANY TIME. BY TAKING POSSESSION
CONDUIT
OF THIS DOCUMENT, THE RECIPIENT ACKNOWLEDGES AND AGREES THAT THIS DOCUMENT CANNOT C
BE USED IN ANY MANNER ADVERSE TO THE INTERESTS OF COOPER LIGHTING SOLUTIONS,AND THAT • Adjustable wrench or ratchet wrench with 8mm and 10mm socket
NO PORTION OF THIS DOCUMENT MAY BE COPIED OR OTHERWISE REPRODUCED WITHOUT THE
PRIOR WRITTEN CONSENT OF COOPER LIGHTING SOLUTIONS. IN THE CASE OF CONFLICTING
CONTRACTUAL PROVISIONS, THIS NOTICE SHALL GOVERN THE STATUS OF THIS DOCUMENT.
7
8 ELECTRONIC CAD DRAWING. DO 7
• Drill with 3/16 in. drill bit
NOT REVISE MANUALLY.
DIMENSIONS ARE IN INCHES
DIMENSIONS IN [ ] ARE IN MM
• 1/2 in. diameter conduit (if applicable, length depends on application)
TOLERANCE GENERAL
ENGLISH (IN) .X
• 1/2 in. watertight conduit connectors (if applicable) .XX
.XXX
METRIC (MM) .X
C
.XX
.XXX
ANGLES ALL
THIRD ANGLE PROJECTION
IMPORTANT SAFETY INSTRUCTIONS
MATERIAL:
When using product, basic precautions should always be followed, including the following:
CONDUIT
CONDUIT
DO NOT SCALE DRAWING
PART NUMBER
CONDUITCONNECTOR B
• Heed all warnings, including below warnings AND those included on product.
3
B
• Save these instructions and warnings.
• For outdoor use only.
• cULus LISTED for wet location.
FIGURE 1
• Disassembling your fixture will void the warranty.
6
• Your fixture is prewired and preassembled for easy installation.
A
PRODUCT MUST CONFORM TO ROHS
COOPER LIGHTING SOLUTIONS - CONFIDENTIAL AND PROPRIETARY
WARNING
NOTICE TO PERSONS RECEIVING THIS DOCUMENT AND/OR TECHNICAL INFORMATION
THIS DOCUMENT, INCLUDING THE DRAWING AND INFORMATION CONTAINED THEREON, IS
CONFIDENTIAL AND IS THE EXCLUSIVE PROPERTY OF EATON, AND IS MERELY ON LOAN
AND SUBJECT TO RECALL BY COOPER LIGHTING SOLUTIONS AT ANY TIME. BY TAKING POSSESSION
A
OF THIS DOCUMENT, THE RECIPIENT ACKNOWLEDGES AND AGREES THAT THIS DOCUMENT CANNOT
BE USED IN ANY MANNER ADVERSE TO THE INTERESTS OF COOPER LIGHTING SOLUTIONS,AND THAT
NO PORTION OF THIS DOCUMENT MAY BE COPIED OR OTHERWISE REPRODUCED WITHOUT THE
PRIOR WRITTEN CONSENT OF COOPER LIGHTING SOLUTIONS. IN THE CASE OF CONFLICTING PRODUCT MUST CONFORM TO ROHS
CONTRACTUAL PROVISIONS, THIS NOTICE SHALL GOVERN THE STATUS OF THIS DOCUMENT.
COOPER LIGHTING SOLUTIONS - CONFIDENTIAL AND PROPRIETARY
8
NOTICE TO PERSONS RECEIVING THIS DOCUMENT AND/OR TECHNICAL INFORMATION
THIS DOCUMENT, INCLUDING THE DRAWING AND INFORMATION CONTAINED THEREON, IS
CONFIDENTIAL AND IS THE EXCLUSIVE PROPERTY OF EATON, AND IS MERELY ON LOAN
AND SUBJECT TO RECALL BY COOPER LIGHTING SOLUTIONS AT ANY TIME. BY TAKING POSSESSION
• Read and follow these instructions.
SION
OF THIS DOCUMENT, THE RECIPIENT ACKNOWLEDGES AND AGREES THAT THIS DOCUMENT CANNOT
T
BE USED IN ANY MANNER ADVERSE TO THE INTERESTS OF COOPER LIGHTING SOLUTIONS,AND THAT
THAT
NO PORTION OF THIS DOCUMENT MAY BE COPIED OR OTHERWISE REPRODUCED WITHOUT THE
• Risk of fire/electric shock. If not qualified, consult an electrician.
PRIOR WRITTEN CONSENT OF COOPER LIGHTING SOLUTIONS. IN THE CASE OF CONFLICTING
CONTRACTUAL PROVISIONS, THIS NOTICE SHALL GOVERN THE STATUS OF THIS DOCUMENT.
6
• Disconnect power at fuse or circuit breaker before installing or servicing. 8
7
• Edges may cut. Handle with care.
CAUTION
• Connect fixture to a 120 Volt, 60 Hz power source. Any other connection voids the
warranty.
• Fixture should be installed by persons with experience in household wiring or by
a qualified electrician. The electrical system, and the method of electrically con-
necting the fixture to it, must be in accordance with the National Electrical Code
and local building codes.
• Upside down installation can result in overheating or accumulation of water in
fixture. Install right side up.
FCC DECLARATION OF CONFORMITY
This device complies with part 15 of the FCC Rules. Operation is subject to the following 2
conditions: (1) This device may not cause harmful interference, and (2) this device must accept
any interference received, including interference that may cause undesired operation.
NOTE: This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This
5
2.125
54
Questions?/ Des questions? / ¿Preguntas? 1-800-334-6871 ConsumerProducts@cooperlighting.com
1.375
35
6
2.750
PACKAGING CONTENTS / CONTENU DE L'EMBALLAGE/ CONTENIDO DEL PAQUETE
70
USE FOR PACKAGING ARTWORK
A. Light fixture
5 4
7
6 5
Appareil d'éclairage
G. DROP REFRACTOR
8 7
Accesorio
B. ACCESS COVER
C. MOUNTING SCREWS
F
H. DROP REFRACTOR MOUNTING SCREWS
I. PHOTOCONTROL SENSOR
A. LIGHT FIXTURE
G. DROP REFRACTOR
F. Pole Mounting Clamp/
E
A. LIGHT FIXTURE
Access Cover Mounting Screws (2)
Collier de fixation pour poteau/vis de
fixation du couvercle d'accés (2)
7 6
E. WIRE CONNECTORS
Tornillos de montaje de la abrazadera de
D
montaje del poste/tapa de acceso (2)
I. PHOTOCONTROL SENSOR
B. ACCESS COVER
CONDUIT
C
CONDUIT CONNECTOR
CONDUIT CONNECTOR
B
FIGURE 1
FIGURE 2
6 5
DIMENSIONS THAT AFFECT 6 DENOTES CRITICAL DENOTES FIRST PIECE
S C P
SAFE HANDLING OR DIMENSIONS AND AND IN-PROCESS
OPERATION GAUGE CHECK POINTS INSPECTION
APPROVALS DATE
A
PRODUCT MUST CONFORM TO ROHS
± 0.040
COOPER LIGHTING SOLUTIONS - CONFIDENTIAL AND PROPRIETARY
± 0.020
DRWN:
± 0.010
NOTICE TO PERSONS RECEIVING THIS DOCUMENT AND/OR TECHNICAL INFORMATION
± 1 THIS DOCUMENT, INCLUDING THE DRAWING AND INFORMATION CONTAINED THEREON, IS
± 0.5
CONFIDENTIAL AND IS THE EXCLUSIVE PROPERTY OF EATON, AND IS MERELY ON LOAN
± 0.25
CHKD:
AND SUBJECT TO RECALL BY COOPER LIGHTING SOLUTIONS AT ANY TIME. BY TAKING POSSESSION
OF THIS DOCUMENT, THE RECIPIENT ACKNOWLEDGES AND AGREES THAT THIS DOCUMENT CANNOT
± 1.0 °
BE USED IN ANY MANNER ADVERSE TO THE INTERESTS OF COOPER LIGHTING SOLUTIONS,AND THAT
NO PORTION OF THIS DOCUMENT MAY BE COPIED OR OTHERWISE REPRODUCED WITHOUT THE APPR: TITLE:
PRIOR WRITTEN CONSENT OF COOPER LIGHTING SOLUTIONS. IN THE CASE OF CONFLICTING
CONTRACTUAL PROVISIONS, THIS NOTICE SHALL GOVERN THE STATUS OF THIS DOCUMENT.
x.x
L MOD: E0439882
8 7/10/2020 7
x.x
FINISH:
DWG NO:
FIGURE 2 SIZE: ALP Instruction Sheets
D Figures
DEV/ZINT NO:
SURFACE AREA:
1125.655 IN2 SCALE: WT: 2.113 LB
CONDUITCONNECTOR
2 1
CONDUIT
CONDUITCONNECTOR
FIGURE 1
FIGURE 1
5
7 6
5 4
7
5
6
F
4 3
Instruction Manual / Manuel d'instructions/ Instrucciones
5 4
B. Access Cover C. Mounting Screws (3)
E 3
6
4
Vis de montage (3)
D. POLE MOUNTING CLAMP
Couverture de l'accés
Tornillos de montaje (3)
6 5
Cubierta acceso
D. POLE MOUNTING CLAMP
B. ACCESS COVER
C. MOUNTING SCREWS I. PHOTOCONTROL SENSOR
B. ACCESS COVER
C. MOUNTING SCREWS
D. POLE MOUNTING CLAMP
E. WIRE CONNECTORS D
G. DROP REFRACTOR
G. Drop Refractor
Réfracteur de chute
F. POLE MOUNTING CLAMP/ACCESS COVER MOUNTING SCREWS
Refractor de caida
5 4
C. MOUNTING SCREWS
FIGURE 2
C
G. DROP REFRACTOR
FIGURE 2
equipment generates uses and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a
CONDUIT B
particular installation. If this equipment does cause harmful interference to radio or tele-
vision reception, which can be determined by turning the equipment off an on, the user is
encouraged to try to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
4
• Increase the separation between the equipment and receiver.
5 DENOTES FIRST 4
F
PIECE
INSPECTION ONLY
• Connect the equipment into an outlet on a circuit different from
F. POLE MOUNTING CLAMP/ACCESS COVER MOUNTING SCREWS
A
• Consult the dealer or an experienced radio/TV technician for help.
5
6
REV:
modifications to this equipment not expressly approved by the manufacturer
FIGURE 2 -
could void the user's authorization to operate this equipment.
CONDUIT
VOL: 58.477 IN3 SHEET 1 OF 1
FIGURE 2
IP LEVEL:
Unique Identifier: Standard Area Light
4 3
Responsible Party – U.S. Contact Information
Cooper Lighting Solutions
1121 Highway 74 S
5 4
Peachtree City, GA
30269
PART NUMBER
www.cooperindustries.com/content/public/en/lighting.html
3
6
4
Telephone Number: 1-800-942-0763
FCC Compliance Statement
This device complies with Part 15 of the FCC Rules. Operation is subject to the following
two conditions: (1) This device may not cause harmful interference, and (2) this device
must accept any interference received, including interference that may cause undesired
operation.
1
2
REV. DESCRIPTION
C. MOUNTING SCREWS
3 2
REVISIONS
REV. DESCRIPTION DATE CHANGE_NUMBER
2.125
54
D. Pole Mounting Clamp
2
5
3
Pince de montage pour
REVISIONS
REV. DESCRIPTION poteau DATE
REV.
4
Pinza de montaje en poste
USE FOR PACKAGING ARTWORK
G. DROP REFRACTOR H. DROP REFRACTOR MOUNTING SCREWS
2.125
54
D. POLE MOUNTING CLAMP
D. POLE MOUNTING CLAMP
H. Drop Refractor Mounting Screws (2)
H. DROP REFRACTOR MOUNTING SCREWS
USE FOR PACKAGING ARTWORK
Vis de montage du réfracteur de chute (2)
Tornillos de montaje del refractor de caida (2)
E. WIRE CONNECTORS
F. POLE MOUNTING CLAMP/ACCESS COVER MOUNTING SCREWS
3 2
REV. DESCRIPTION
C. MOUNTING SCREWS
F. POLE MOUNTING CLAMP/ACCESS COVER MOUNTING SCREWS
2.125
[54] 2.125
H. DROP REFRACTOR MOUNTING SCREWS
54
E. WIRE CONNECTORS
D. POLE MOUNTING CLAMP
1.375
35
2.750
[70]
USE FOR PACKAGING ARTWORK
ELECTRONIC CAD DRAWING. DO
NOT REVISE MANUALLY.
DIMENSIONS ARE IN INCHES
DIMENSIONS IN [ ] ARE IN MM
C. MOUNTING SCREWS
TOLERANCE
ENGLISH (IN)
METRIC (MM)
F. POLE MOUNTING CLAMP/ACCESS COVER MOUNTING SCREWS
ELECTRONIC CAD DRAWING. DO DIMENSIONS THAT AFFECT DENOTES CRITICAL
S C H. DROP REFRACTOR MOUNTING SCREWS
NOT REVISE MANUALLY. SAFE HANDLING OR DIMENSIONS AND
OPERATION ANGLES GAUGE CHECK POINTS
DIMENSIONS ARE IN INCHES
E. WIRE CONNECTORS
DIMENSIONS IN [ ] ARE IN MM
FIGURE 2
APPROVALS
TOLERANCE GENERAL DATE
THIRD ANGLE PROJECTION
ENGLISH (IN) .X ± 0.040
.XX ± 0.020
.XXX ± 0.010 DRWN:
METRIC (MM) .X ± 1
.XX ± 0.5
.XXX ± 0.25
CHKD:
ANGLES ALL
± 1.0 °
MATERIAL:
APPR: TITLE:
THIRD ANGLE PROJECTION
x.x
L MOD: E0439882
7/10/2020
x.x
FINISH:
MATERIAL:
DWG NO:
SIZE:
D
PART NUMBER DO NOT SCALE DRAWING
DEV/ZINT NO:
PART NUMBER DO NOT SCALE DRAWING SURFACE AREA:
818.746 IN2 SCALE:
3
3 2
that to which the receiver is connected.
F. POLE MOUNTING CLAMP/ACCESS COVER MOUNTING SCREWS
WARNING: FCC Regulations state that any unauthorized changes or
4 3
ELECTRONIC CAD DRAWING. DO DIMENSIONS THAT AFFECT
F. POLE MOUNTING CLAMP/ACCESS COVER MOUNTING SCREWS S
NOT REVISE MANUALLY. SAFE HANDLING OR
FIGURE 2
OPERATION
DIMENSIONS ARE IN INCHES
DIMENSIONS IN [ ] ARE IN MM
APPROVALS
TOLERANCE GENERAL
ENGLISH (IN)
.X ± 0.040
.XX ± 0.020
DRWN:
.XXX ± 0.010
METRIC (MM) .X ± 1
.XX ± 0.5
.XXX ± 0.25
CHKD:
ANGLES ALL
± 1.0 °
Supplier's Declaration of Conformity
APPR:
THIRD ANGLE PROJECTION
x.x
L MOD: E0439882
47 CFR § 2.1077 Compliance Information
x.x
MATERIAL: FINISH:
DO NOT SCALE DRAWING
PART NUMBER ELECTRONIC CAD DRAWING. DO SURFACE AREA: DIMENSIONS THAT AFFECT
S 1125.655 IN2
NOT REVISE MANUALLY. SAFE HANDLING OR
DIMENSIONS ARE IN INCHES OPERATION
DIMENSIONS IN [ ] ARE IN MM
2
APPROVALS
ELECTRONIC CAD DRAWING. DO DIMENSIONS THAT AFFECT TOLERANCE GENERAL DENOTES CRITICAL
S C ELECTRONIC CAD DRAWING. DO
NOT REVISE MANUALLY. SAFE HANDLING OR DIMENSIONS AND
ENGLISH (IN) .X ± 0.040 NOT REVISE MANUALLY.
OPERATION .XX ± 0.020 GAUGE CHECK POINTS
DIMENSIONS ARE IN INCHES DRWN:
.XXX ± 0.010
METRIC (MM) .X ± 1 DIMENSIONS ARE IN INCHES
DIMENSIONS IN [ ] ARE IN MM .XX ± 0.5
.XXX ± 0.25 CHKD:
DIMENSIONS IN [ ] ARE IN MM
APPROVALS ANGLES ALL
± 1.0 ° DATE
TOLERANCE GENERAL
TOLERANCE APPR:
THIRD ANGLE PROJECTION
ENGLISH (IN) x.x
.X ± 0.040
L MOD: E0439882
.XX ± 0.020 ENGLISH (IN)
DRWN:
.XXX ± 0.010 x.x
MATERIAL: FINISH:
METRIC (MM) .X ± 1
.XX ± 0.5 METRIC (MM)
.XXX ± 0.25
CHKD:
ANGLES ALL
± 1.0 °
ANGLES
DO NOT SCALE DRAWING
PART NUMBER SURFACE AREA:
APPR:
THIRD ANGLE PROJECTION
3 2
THIRD ANGLE PROJECTION
x.x
L MOD: E0439882 7/10/2020
x.x
MATERIAL: FINISH:
MATERIAL:
DO NOT SCALE DRAWING
SURFACE AREA: 1125.655 IN2
DO NOT SCALE DRAWING
PART NUMBER
2
5
3
2.750
70
USE FOR PACKAGING ARTWORK
1
REVISIONS
DATE CHANGE_NUMBER BY APPROVED
1
H. DROP REFRACTOR MOUNTING SCREWS
BY APPROVED
E. Wire Connectors (3)
1
4
2
F
Serre-fil (3)
REVISIONS
1.375
CHANGE_NUMBER BY APPROVED
DESCRIPTION DATE CHANGE_NUMBER
35
Conectores de cable (3)
3 2
REVISIONS
2.750
70
REV. DESCRIPTION DATE CHANGE_NUMBER
F
E
E. WIRE CONNECTORS
2.125
54
D. POLE MOUNTING
1.375
1.375
G. DROP REFRACTOR
35
35
2.750
2.750
70
G. DROP REFRACTOR H. DROP REFRACTOR MOUNTING SCREWS
70
D
USE FOR PACKAGING ARTWORK
E
1
REVISIONS
DATE CHANGE_NUMBER BY APPROVED
C. MOUNTING SCREWS
C
F
H. DROP REFRACTOR MOUNTING SCREWS
1.375
35
2.750
D
70
USE FOR PACKAGING ARTWORK
E
2.125
B
[54]
DIMENSIONS THAT AFFECT DENOTES CRITICAL DENOTES FIRST PIECE
S C
P
SAFE HANDLING OR DIMENSIONS AND AND IN-PROCESS
OPERATION GAUGE CHECK POINTS INSPECTION
1.375
35
APPROVALS
DATE
GENERAL
2.750
[70]
.X ± 0.040
.XX ± 0.020
USE FOR PACKAGING ARTWORK
DRWN:
.XXX ± 0.010
.X ± 1
.XX ± 0.5
.XXX ± 0.25 DENOTES FIRST PIECE DENOTES FIRST
CHKD:
P F
AND IN-PROCESS PIECE
ALL INSPECTION INSPECTION ONLY
± 1.0 °
E. WIRE CONNECTORS
APPR:
TITLE:
x.x
L MOD: E0439882 7/10/2020
D
A
x.x
FINISH:
SIZE: DWG NO:
ALP Instruction Sheets
D Figures
C
REV: DEV/ZINT NO:
ALS Integrated Photocell
-
Instruction Sheets Figures
SURFACE AREA: 1125.655 IN2
SCALE: WT: 2.113 LB
ELECTRONIC CAD DRAWING. DO DIMENSIONS THAT AFFECT DENOTES CRITICAL
WT: 1.065 LB VOL: 29.468 IN3 SHEET 1 OF 1
2 S C
NOT REVISE MANUALLY. SAFE HANDLING OR DIMENSIONS AND
OPERATION GAUGE CHECK POINTS
1 DIMENSIONS ARE IN INCHES IP LEVEL:
DIMENSIONS IN [ ] ARE IN MM
APPROVALS DATE
TOLERANCE GENERAL
E. WIRE CONNECTORS
ENGLISH (IN) .X ± 0.040
.XX ± 0.020
DRWN:
.XXX ± 0.010
METRIC (MM) .X ± 1
.XX ± 0.5
.XXX ± 0.25
CHKD:
ANGLES ALL
± 1.0 °
APPR: TITLE:
THIRD ANGLE PROJECTION
C
x.x
L MOD: E0439882 7/10/2020
x.x
MATERIAL: FINISH:
SIZE: DWG NO: ALS Integrated Photocell
D Instruction Sheets Figures
DEV/ZINT NO:
PART NUMBER DO NOT SCALE DRAWING
SURFACE AREA: 818.746 IN2 SCALE: WT: 1.065 LB
2
DENOTES CRITICAL DENOTES FIRST PIECE
DENOTES FIRST
C P F
DIMENSIONS AND AND IN-PROCESS PIECE
GAUGE CHECK POINTS INSPECTION INSPECTION ONLY
DATE
B
B
TITLE:
7/10/2020
REV:
SIZE: DWG NO: ALP Instruction Sheets
-
D Figures
DEV/ZINT NO:
DENOTES CRITICAL DENOTES FIRST PIECE DENOTES FIRST
C SCALE: 2.113 LB 58.477 IN3 SHEET 1 OF 1
DIMENSIONS AND WT: P AND IN-PROCESS F VOL: PIECE
GAUGE CHECK POINTS INSPECTION INSPECTION ONLY
1 IP LEVEL:
DATE
DENOTES FIRST PIECE DENOTES FIRST
P DIMENSIONS THAT AFFECT F DENOTES CRITICAL
AND IN-PROCESS PIECE
S C P
SAFE HANDLING OR DIMENSIONS AND
INSPECTION INSPECTION ONLY
OPERATION GAUGE CHECK POINTS
A
APPROVALS
DATE
GENERAL TITLE:
7/10/2020
.X ± 0.040
.XX ± 0.020
DRWN:
.XXX ± 0.010
SIZE: DWG NO: REV:
ALP Instruction Sheets
.X ± 1
- A
.XX ± 0.5 D Figures
.XXX ± 0.25
CHKD:
DEV/ZINT NO:
ALL
± 1.0 °
1125.655 IN2 SCALE: WT: 2.113 LB VOL: 58.477 IN3 SHEET 1 OF 1
TITLE:
APPR: TITLE:
1 IP LEVEL:
x.x
L MOD: E0439882 7/10/2020
x.x
SIZE: DWG NO: ALP Instruction Sheets FINISH: REV:
SIZE: DWG NO: ALP Instruction Sheets
-
D Figures
D Figures
DEV/ZINT NO:
DEV/ZINT NO:
SCALE: 58.477 IN3 1 OF 1
WT: 2.113 LB VOL: SHEET
SURFACE AREA:
1125.655 IN2 SCALE:
WT: 2.113 LB
1 IP LEVEL:
4 3
2
F
3
1
BY AP
1
BY APPROVED
E
D
C
DENOTES FIRST
F
PIECE
INSPECTION ON
1
VOL: 58.477 IN3 SHEET
DENOTES FIRST PIECE DENOTES FIRST
P 1 B F IP
AND IN-PROCESS PIECE
INSPECTION INSPECTION ONLY
F. P
REV:
-
VOL: 29.468 IN3 SHEET 1 OF 1
1 IP LEVEL:
A
DENOTES FIRST PIECE
DENOTE
F
AND IN-PROCESS
PIECE
INSPECTION
INSPEC
PART NUMBER
58.477 IN3 SHE
VOL:
1