Cooper Lighting Solutions Halo ALB7A40GY Instruction Manual

3
OL SENSOR 6
REV.
G. DROP REFRACTOR
8 7
D. POLE MOUNTING CLAMP
7
B. ACCESS COVER
F
F
E
A. LIGHT FIXTURE
ALB7A40GY
C. MOUNTING SCREWS
D
. LIGHT FIXTURE
E
C
FIGURE 2 D
CONDUIT CONNECTOR
B
ENGLISH
FIGURE 1
F. POLE MOUNTING CLAMP/ACCESS COVER MOUNTING SCREWS
ITEMS REQUIRED
A
(Purchase separately)
PRODUCT MUST CONFORM TO ROHS
COOPER LIGHTING SOLUTIONS - CONFIDENTIAL AND PROPRIETARY
NOTICE TO PERSONS RECEIVING THIS DOCUMENT AND/OR TECHNICAL INFORMATION
• Phillips screwdriver
THIS DOCUMENT, INCLUDING THE DRAWING AND INFORMATION CONTAINED THEREON, IS
CONFIDENTIAL AND IS THE EXCLUSIVE PROPERTY OF EATON, AND IS MERELY ON LOAN
AND SUBJECT TO RECALL BY COOPER LIGHTING SOLUTIONS AT ANY TIME. BY TAKING POSSESSION
OF THIS DOCUMENT, THE RECIPIENT ACKNOWLEDGES AND AGREES THAT THIS DOCUMENT CANNOT
CONDUIT
C
BE USED IN ANY MANNER ADVERSE TO THE INTERESTS OF COOPER LIGHTING SOLUTIONS,AND THAT
• Adjustable wrench or ratchet wrench with 8mm and 10mm socket
NO PORTION OF THIS DOCUMENT MAY BE COPIED OR OTHERWISE REPRODUCED WITHOUT THE
CONDUITCONNECTOR PRIOR WRITTEN CONSENT OF COOPER LIGHTING SOLUTIONS. IN THE CASE OF CONFLICTING
CONTRACTUAL PROVISIONS, THIS NOTICE SHALL GOVERN THE STATUS OF THIS DOCUMENT.
8 7
• Drill with 3/16 in. drill bit
• 1/2 in. diameter conduit (if applicable, length depends on application)
• 1/2 in. watertight conduit connectors (if applicable)
URE 1
ELECTRONIC CAD DRAWING. DO
5 NOT REVISE MANUALLY.
IMPORTANT SAFETY INSTRUCTIONS
DIMENSIONS ARE IN INCHES
DIMENSIONS IN [ ] ARE IN MM
TOLERANCE GENERAL
ENGLISH (IN)
When using product, basic precautions should always be followed, including the following: .X ± 0.040
.XX ± 0.020
.XXX ± 0.010
METRIC (MM) .X ± 1
.XX ± 0.5
B CONDUITCONNECTOR .XXX ± 0.25
• Heed all warnings, including below warnings AND those included on product.
ANGLES ALL
± 1.0 °
THIRD ANGLE PROJECTION
• Save these instructions and warnings.
x.x
MATERIAL:
• For outdoor use only.
• cULus LISTED for wet location.
FIGURE 1
DO NOT SCALE DRAWING
PART NUMBER
• Disassembling your fixture will void the warranty.
3
2
6
• Your fixture is prewired and preassembled for easy installation.
WARNING
A
PRODUCT MUST CONFORM TO ROHS
COOPER LIGHTING SOLUTIONS - CONFIDENTIAL AND PROPRIETARY
NTIAL AND PROPRIETARY
NOTICE TO PERSONS RECEIVING THIS DOCUMENT AND/OR TECHNICAL INFORMATION
OCUMENT AND/OR TECHNICAL INFORMATION
THIS DOCUMENT, INCLUDING THE DRAWING AND INFORMATION CONTAINED THEREON, IS
ND INFORMATION CONTAINED THEREON, IS
CONFIDENTIAL AND IS THE EXCLUSIVE PROPERTY OF EATON, AND IS MERELY ON LOAN
ERTY OF EATON, AND IS MERELY ON LOAN
AND SUBJECT TO RECALL BY COOPER LIGHTING SOLUTIONS AT ANY TIME. BY TAKING POSSESSION
• Read and follow these instructions.
ING SOLUTIONS AT ANY TIME. BY TAKING POSSESSION
OF THIS DOCUMENT, THE RECIPIENT ACKNOWLEDGES AND AGREES THAT THIS DOCUMENT CANNOT
LEDGES AND AGREES THAT THIS DOCUMENT CANNOT
BE USED IN ANY MANNER ADVERSE TO THE INTERESTS OF COOPER LIGHTING SOLUTIONS,AND THAT
INTERESTS OF COOPER LIGHTING SOLUTIONS,AND THAT
NO PORTION OF THIS DOCUMENT MAY BE COPIED OR OTHERWISE REPRODUCED WITHOUT THE
PIED OR OTHERWISE REPRODUCED WITHOUT THE • Risk of fire/electric shock. If not qualified, consult an electrician.
PRIOR WRITTEN CONSENT OF COOPER LIGHTING SOLUTIONS. IN THE CASE OF CONFLICTING
NG SOLUTIONS. IN THE CASE OF CONFLICTING
CONTRACTUAL PROVISIONS, THIS NOTICE SHALL GOVERN THE STATUS OF THIS DOCUMENT.
ALL GOVERN THE STATUS OF THIS DOCUMENT.
• Disconnect power at fuse or circuit breaker before installing or servicing.
7
• Edges may cut. Handle with care.
CAUTION
• Connect fixture to a 120 Volt, 60 Hz power source. Any other connection voids the
warranty.
• Fixture should be installed by persons with experience in household wiring or by
a qualified electrician. The electrical system, and the method of electrically con-
necting the fixture to it, must be in accordance with the National Electrical Code
and local building codes.
• Upside down installation can result in overheating or accumulation of water in
fixture. Install right side up.
FCC DECLARATION OF CONFORMITY
This device complies with part 15 of the FCC Rules. Operation is subject to the following 2
conditions: (1) This device may not cause harmful interference, and (2) this device must accept
any interference received, including interference that may cause undesired operation.
NOTE: This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This
2 1
5
REVISIONS
D. POLE MOUNTING CLAMP
DESCRIPTION DATE CHANGE_NUMBER BY
Questions?/ Des questions? / ¿Preguntas? 1-800-334-6871 ConsumerProducts@cooperlighting.com
6
PACKAGING CONTENTS / CONTENU DE L'EMBALLAGE/ CONTENIDO DEL PAQUETE
2.125
54
A. Light fixture
8 7
6
I. PHOTOCONTROL SENSOR
C. MOUNTING SCREWS
1.375
8 7
Appareil d'éclairage
35
2.750
70
Accesorio
B. ACCESS COVER
USE FOR PACKAGING ARTWORK
C. MOUNTING SCREWS
F
I. PHOTOCONTROL SENSOR
B. ACCESS COVER
E
A. LIGHT FIXTURE
H. DROP REFRACTOR MOUNTING SCREWS
E. Wire Connectors (3)
A. LIGHT FIXTURE
Serre-fil (3)
Conectores de cable (3)
D
E. WIRE CONNECTORS
C
CONDUIT
CONDUIT CONNECTOR
B
FIGURE 1
FIGURE 2
6
A
PRODUCT MUST CONFORM TO ROHS
COOPER LIGHTING SOLUTIONS - CONFIDENTIAL AND PROPRIETARY
NOTICE TO PERSONS RECEIVING THIS DOCUMENT AND/OR TECHNICAL INFORMATION
THIS DOCUMENT, INCLUDING THE DRAWING AND INFORMATION CONTAINED THEREON, IS
CONFIDENTIAL AND IS THE EXCLUSIVE PROPERTY OF EATON, AND IS MERELY ON LOAN
AND SUBJECT TO RECALL BY COOPER LIGHTING SOLUTIONS AT ANY TIME. BY TAKING POSSESSION
OF THIS DOCUMENT, THE RECIPIENT ACKNOWLEDGES AND AGREES THAT THIS DOCUMENT CANNOT
BE USED IN ANY MANNER ADVERSE TO THE INTERESTS OF COOPER LIGHTING SOLUTIONS,AND THAT
NO PORTION OF THIS DOCUMENT MAY BE COPIED OR OTHERWISE REPRODUCED WITHOUT THE
PRIOR WRITTEN CONSENT OF COOPER LIGHTING SOLUTIONS. IN THE CASE OF CONFLICTING
CONTRACTUAL PROVISIONS, THIS NOTICE SHALL GOVERN THE STATUS OF THIS DOCUMENT.
8 7
PART NUMBER
DIMENSIONS THAT AFFECT DENOTES CRITICAL DENOTES FIRST PIECE
S C P
SAFE HANDLING OR DIMENSIONS AND AND IN-PROCESS
4 3
OPERATION GAUGE CHECK POINTS INSPECTION
APPROVALS
DATE
DRWN:
CONDUIT
CONDUITCONNECTOR
CHKD:
APPR: TITLE:
L MOD: E0439882
7/10/2020
x.x
FINISH:
SIZE: DWG NO: ALP Instruction Sheets
D Figures
DEV/ZINT NO: FIGURE 1
SURFACE AREA:
1125.655 IN2 SCALE: 58.477 IN3
WT: 2.113 LB VOL:
1
5
8 7
6
2.125
54
4
APPROVED Instruction Manual / Manuel d'instructions/ Instrucciones
USE FOR PACKAGING ARTWORK
F
5 4
B. Access Cover C. Mounting Screws (3)
6
5
Couverture de l'accés
6 5
G. DROP REFRACTOR
Cubierta acceso
H. DROP REFRACTOR MOUNTING SCREWS
D. POLE MOUNTING CLAMP
E
B. ACCESS COVER
C. MOUNTING SCREWS
I. PHOTOCONTROL SENSOR
B. ACCESS COVER
C. MOUNTING SCREWS
E. WIRE CONNECTORS
G. DROP REFRACTOR
F. Pole Mounting Clamp/Access Cover Mounting Screws (2)
E. WIRE CONNECTORS
Collier de fixation pour poteau/vis de fixation du couvercle d'accés (2)
F. POLE MOUNTING CLAMP/ACCESS COVER MOUNTING SCREWS
D
Tornillos de montaje de la abrazadera de montaje del poste/tapa de acceso (2)
F. POLE MOUNTING CLAMP/ACCESS COVER MOUNTING SCREWS
FIGURE 2
C
equipment generates uses and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause harmful interference to radio
CONDUIT
communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or tele-
vision reception, which can be determined by turning the equipment off an on, the user is
ELECTRONIC CAD DRAWING. DO DIMENSIONS THAT AFFECT
S
NOT REVISE MANUALLY. SAFE HANDLING OR
OPERATION
DIMENSIONS ARE IN INCHES encouraged to try to correct the interference by one or more of the following measures:
DIMENSIONS IN [ ] ARE IN MM
APPROVALS
TOLERANCE GENERAL
• Reorient or relocate the receiving antenna.
B
ENGLISH (IN)
.X ± 0.040
.XX ± 0.020
DRWN:
.XXX ± 0.010
METRIC (MM) .X ± 1
.XX ± 0.5 • Increase the separation between the equipment and receiver.
5 4
.XXX ± 0.25
CHKD:
ANGLES ALL
± 1.0 °
APPR:
• Connect the equipment into an outlet on a circuit different from
THIRD ANGLE PROJECTION
x.x
L MOD: E0439882 7/10/2020
x.x
MATERIAL: FINISH:
• Consult the dealer or an experienced radio/TV technician for help.
6 5
DO NOT SCALE DRAWING
SURFACE AREA: 1125.655 IN2
DENOTES FIRST WARNING: FCC Regulations state that any unauthorized changes or
F
PIECE 2
INSPECTION ONLY
modifications to this equipment not expressly approved by the manufacturer
FIGURE 2
could void the user's authorization to operate this equipment.
CONDUIT
A
REV:
-
SHEET 1 OF 1
IP LEVEL:
Unique Identifier: Basic Area Light
4
Responsible Party – U.S. Contact Information
Cooper Lighting Solutions
1121 Highway 74 S
Peachtree City, GA
30269
www.cooperindustries.com/content/public/en/lighting.html
6
5
Telephone Number: 1-800-942-0763
FCC Compliance Statement
This device complies with Part 15 of the FCC Rules. Operation is subject to the following
two conditions: (1) This device may not cause harmful interference, and (2) this device
must accept any interference received, including interference that may cause undesired
operation.
1
3 2
1.375
REV. DESCRIPTION
35
2.750
70
E
3 2
REVISIONS
REV. DESCRIPTION DATE CHANGE_NUMBER
2.125
54
D. Pole Mounting Clamp
5
4 3
Vis de montage (3)
D. POLE MOUNTING CLAMP
4
Tornillos de montaje (3)
D
D. POLE MOUNTING CLAMP
D. POLE MOUNTING CLAMP
H. DROP REFRACTOR MOUNTING SCREWS
E. WIRE CONNECTORS
C
F. POLE MOUNTING CLAMP/ACCESS COVER MOUNTING SCREWS
C. MOUNTING SCREWS
2.125
[54]
1.375
35
2.750
[70]
USE FOR PACKAGING ARTWORK
B
FIGURE 2
F. POLE MOUNTING CLAMP/ACCESS COVER MOUNTING SCREWS DIMENSIONS THAT AFFECT DENOTES CRITICAL
ELECTRONIC CAD DRAWING. DO
S C
NOT REVISE MANUALLY. SAFE HANDLING OR DIMENSIONS AND
DIMENSIONS ARE IN INCHES OPERATION GAUGE CHECK POINTS
DIMENSIONS IN [ ] ARE IN MM
APPROVALS DATE
TOLERANCE GENERAL
ENGLISH (IN)
.X 0.040
.XX 0.020
DRWN:
.XXX 0.010
METRIC (MM) .X 1
.XX 0.5
.XXX 0.25
CHKD:
DENOTES CRITICAL ANGLES ALL
DENOTES FIRST PIECE 1.0 DENOTES FIRST
C P F
DIMENSIONS AND AND IN-PROCESS
APPR: PIECE
TITLE:
THIRD ANGLE PROJECTION
GAUGE CHECK POINTS INSPECTION
INSPECTION ONLY
x.x
L MOD: E0439882 8/10/2020
x.x
MATERIAL: FINISH:
DATE
SIZE: DWG NO:
D
DEV/ZINT NO:
PART NUMBER DO NOT SCALE DRAWING SURFACE AREA:
818.746 IN2 SCALE: WT:
3 2 A
TITLE:
that to which the receiver is connected.
REV:
SIZE: DWG NO: ALP Instruction Sheets
-
D Figures
4 3
DEV/ZINT NO:
SCALE: 58.477 IN3 1 OF 1
WT: 2.113 LB VOL: SHEET
IP LEVEL:
1
ELECTRONIC CAD DRAWING. DO
NOT REVISE MANUALLY.
FIGURE 2
DIMENSIONS ARE IN INCHES
DIMENSIONS IN [ ] ARE IN MM
TOLERANCE GENERAL
ENGLISH (IN)
.X ± 0.040
.XX ± 0.020
DRWN:
.XXX ± 0.010
METRIC (MM) .X ± 1
.XX ± 0.5
.XXX ± 0.25
CHKD:
ANGLES ALL
± 1.0 °
Supplier's Declaration of Conformity
APPR:
THIRD ANGLE PROJECTION
x.x
L MOD: E0439882
47 CFR § 2.1077 Compliance Information
x.x
MATERIAL: FINISH:
DO NOT SCALE DRAWING
PART NUMBER
3
2
5
4 3
1
REVISIONS
DATE CHANGE_NUMBER BY
1
BY APPROVED
4
2
F
Pince de montage pour
3 2
1.375
REVISIONS
poteau
REV. DESCRIPTION
35
REV. DESCRIPTION DATE CHANGE_NUMBER
2.750
Pinza de montaje en poste
70
USE FOR PACKAGING ARTWORK
E
2.125
54
G. DROP REFRACTOR
D
USE FOR PACKAGING
C. MOUNTING SCREWS
C
H. DROP REFRACTOR MOUNTIN
E. WIRE CONNECTORS
2.125
[54]
B
1.375
35
2.750
[70]
USE FOR PACKAGING ARTWORK
DENOTES FIRST PIECE
DENOTES FIRST
P
AND IN-PROCESS F PIECE
INSPECTION INSPECTION ONLY
E. WIRE CONNECT
A
REV:
ALS Integrated Photocell ELECTRONIC CAD DRAWING. DO DIMENSIONS THAT AFFECT DENOTES CRITICAL
S C P
NOT REVISE MANUALLY. - SAFE HANDLING OR DIMENSIONS AND
Instruction Sheets Figures OPERATION GAUGE CHECK POINTS
DIMENSIONS ARE IN INCHES
DIMENSIONS IN [ ] ARE IN MM
APPROVALS
TOLERANCE GENERAL DATE
1.065 LB VOL: 29.468 IN3 SHEET 1 OF 1
ENGLISH (IN) .X 0.040
IP LEVEL:
1 .XX 0.020 DRWN:
.XXX 0.010
METRIC (MM) .X 1
.XX 0.5
.XXX 0.25 CHKD:
ANGLES ALL
1.0
APPR: TITLE:
THIRD ANGLE PROJECTION
x.x
L MOD: E0439882
8/10/2020
x.x
MATERIAL: FINISH:
SIZE: DWG NO:
ALS Integrated Photocell
D Instruction Sheets Figures
DEV/ZINT NO:
F. POLE MOUNTING CLAMP/ACCESS COVER MOUNTING S
DO NOT SCALE DRAWING
PART NUMBER SURFACE AREA: 818.746 IN2
SCALE: WT: 1.065 LB
2
DIMENSIONS THAT AFFECT DENOTES CRITICAL DENOTES FIRST PIECE
S C P F
SAFE HANDLING OR DIMENSIONS AND AND IN-PROCESS
OPERATION GAUGE CHECK POINTS INSPECTION
APPROVALS
DATE
TITLE:
7/10/2020
SIZE: DWG NO: ALP Instruction Sheets
D Figures
DEV/ZINT NO:
SURFACE AREA:
1125.655 IN2 SCALE: 2.113 LB 58.477 IN3
WT: VOL:
1
ELECTRONIC CAD DRAWING. DO DIMENSIONS THAT AFFECT
S
NOT REVISE MANUALLY. SAFE HANDLING OR
OPERATION
DIMENSIONS ARE IN INCHES
DIMENSIONS IN [ ] ARE IN MM
APPROVALS
TOLERANCE GENERAL
ENGLISH (IN)
.X ± 0.040
.XX ± 0.020
DRWN:
.XXX ± 0.010
METRIC (MM) .X ± 1
.XX ± 0.5
.XXX ± 0.25
CHKD:
ANGLES ALL
± 1.0 °
APPR:
THIRD ANGLE PROJECTION
x.x
L MOD: E0439882
x.x
MATERIAL: FINISH:
DO NOT SCALE DRAWING
PART NUMBER SURFACE AREA:
1125.655 IN2
4
2
APPROVED
F
3
REVISIONS
1
DATE C
BY APPROVED
E
D. POLE MOUN
1.375
35
2.75
70
D
C
DENOTES FIRST PIECE DENOTES FIRST
F
AND IN-PROCESS PIECE
INSPECTION INSPECTION ONLY
B
REV:
-
1 OF 1
VOL: 29.468 IN3 SHEET
1 IP LEVEL:
DENOTES FIRST
PIECE
INSPECTION ONLY
A
REV:
-
SHEET 1 OF 1
IP LEVEL:
DENOTES CRITICA
C
DIMENSIONS AND
GAUGE CHECK PO
DATE
TITLE:
7/10/2020
SIZE: D
D
D
PART NUMBER
SCALE:
3